Sale!
PP885R
PP885R
PP885R

ABB PP885 3BSE069276R1 Panel 800 15.4″ HMI Operator Panel

  • Model: ABB PP885 3BSE069276R1
  • Brand: ABB
  • Series: Panel 800 High Performance
  • Core Function: Advanced process visualization HMI
  • Product Type: Operator panel (15.4″ widescreen touchscreen)
  • Key Specs: 1280×800 TFT; Intel Atom; 3x USB; IP65 front
  • Condition: New Original / New Surplus
Get a Quote
Categories: , , , , , Brand:

Description

Key Technical Specifications

Parameter Value
Display type 15.4″ TFT-LCD with LED backlight
Resolution 1280 x 800 pixels (WXGA), 262k colors
Brightness 450 cd/m²
Touch screen Resistive analog, 1 million operations
Processor Intel Atom
Memory RAM 1 GB DDR3
Storage 1 x SD card slot (up to 2 GB FAT32)
Ethernet ports 2x (1x 10/100/1000 Mbps, 1x 10/100 Mbps)
USB ports 3 x USB 2.0 Host (500 mA max total)
Serial ports 4x RS232/RS422/RS485 (COM1-4)
Power supply 24 V DC (18-32 V), 3.15 A slow fuse
Power consumption 24 W max
Operating temperature -10 to +50 °C
Front protection IP65 NEMA 4X
Rear protection IP20
Dimensions (W x H x D) 410 x 286 x 83 mm
Cutout dimensions 394 x 270 mm
Weight 3.85 kg
Backlight lifetime 50,000 hours
PP885R
PP885 3BSE069276R1
  1. Product Introduction
    The ABB PP885 3BSE069276R1 is a 15.4-inch high-performance widescreen operator panel from Panel 800 Version 6, designed for System 800xA and AC 800M HMI applications. The Intel Atom processor drives complex vector graphics, trends, and alarms across dual Ethernet and four serial ports for multi-device connectivity.

Control room operators rely on its 1280×800 display for detailed process mimicry and diagnostics, while the IP65 front survives washdown environments. The wide -10 to +50 °C range and galvanic isolation make it suitable for harsh plant floors where larger HMIs replace multiple smaller panels.

  1. Troubleshooting Quick Reference
Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
No display or power LED 24 V reversed or fuse blown ✅ High Measure 18-32 V DC polarity (+24V to 0V); check 3.15 A fuse continuity Correct wiring first; replace fuse then panel if shorted.
Touch calibration drift Surface wear or USB config lost ✅ High Run Panel Builder touch calibration; test multi-point response Recalibrate via USB PC; replace if resistive layer fails edge detection.
Ethernet Port 1/2 no link Gigabit cable issue or IP conflict ✅ Medium Check shielded RJ45 LEDs; ping 192.168.0.250 default Use Cat5e+ for gigabit; reset network via Panel Builder before swap.
Project fails to load from SD Corrupt SD card or 2 GB format limit ✅ High Test FAT32 <2 GB SD; reload via Ethernet from engineering station Reformat SD; use Ethernet download if card slot dead.
Backlight dim after 20k hours LED degradation or thermal overload ✅ High Verify case <50 °C; note total hours counter Confirm ventilation; backlight failure requires full panel replacement.
USB ports drop devices 500 mA total limit exceeded ✅ Medium Test single device <500 mA; check Panel Builder USB power settings No hubs; power cycle if enumeration fails repeatedly.
Serial COM dropout under load RS485 termination missing or baud wrong ✅ Low Add 120Ω terminator at bus ends; loopback test each port Match controller baud/parity; test cable shielding before panel blame.
Random reboots in high EMI areas Poor ground or 24 V noise pickup ✅ Medium Check chassis ground bond <1Ω; add ferrite on power leads 360° shield clamp; separate 24 V from AC power runs by 12 inches minimum.

Capture power polarity photo, Ethernet LEDs, SD slot status, and error dialogs—traces most HMI failures to installation slop rather than hardware death.

  1. Frequently Asked Questions (FAQ)

Q1: What PLCs and systems connect to ABB PP885 3BSE069276R1?
Full Panel 800 driver suite: AC 800M native, Modbus TCP/RTU, Ethernet/IP, Profinet, Profibus, CANopen, plus 100+ PLC brands. Runs Panel Builder .NET projects for complex graphics on Intel Atom hardware.

Q2: Panel cutout tolerances and mounting depth?
394 x 270 mm cutout (±1 mm, max 4 mm corner radius); 76 mm depth (176 mm clearance recommended). IP65 seal requires flat panel <1 mm overall—warped doors leak. Torque M4 screws to 1.0 Nm max.

Q3: SD card and firmware update process?
FAT32 format, 2 GB maximum. Insert formatted SD with Panel Builder project—auto loads on boot (8 minutes). Backup via Ethernet first; mismatch bricks the unit until hard reset via service mode.

Q4: Dual Ethernet port differences?
Port 1: 10/100/1000 Mbps gigabit for engineering; Port 2: 10/100 Mbps for runtime. Both shielded RJ45 with galvanic isolation—use Cat5e+ for gigabit stability over long runs.

Q5: +50 °C limit with IP65 seal realistic?
Intermittent duty only. Sealed cabinets hit thermal wall fast—needs rear fan or ventilation. Direct sunlight or steam drops backlight from 50k to 15k hours; derate to +40 °C continuous.

Q6: New Surplus PP885 quality verification?
OEM from panel builder overruns—bench test confirms full brightness (450 nits), touch matrix, SD slot, all USB/serial ports, dual Ethernet links. Firmware must match your Panel Builder version.

Q7: Warranty scope and test deliverables?
12 months after complete validation: power-up through all screens, touch calibration pass, SD project load, USB enumeration, serial loopbacks, network ping response. Serial-specific test video required.

Related products