Description
Key Technical Specifications
Bosch Rexroth part number R911291332 corresponds to MHD093A-035-PG0-BA. The details below are listed by product-reference sources; verify ratings, mounting, and drive compatibility against the motor nameplate and applicable Rexroth documentation before installation.
- Manufacturer: Bosch Rexroth Indramat.
- Model: MHD093A-035-PG0-BA.
- Rexroth part number: R911291332.
- Motor family: MHD permanent-magnet synchronous motor.
- Frame size: 093.
- Cooling: Natural convection.
- Continuous torque at standstill: 12.0 Nm.
- Feedback: Digital servo feedback with absolute position detection.
- Shaft: Plain shaft with shaft seal.
- Flange size: 140/150 mm.
- Centering diameter: 130 mm.
- Winding code: 035, as encoded in the model number; confirm electrical ratings from the motor data sheet.
- Brake: PG0 configuration; do not assume a holding brake is included. Confirm from the nameplate and order documentation.
- Operating limits, dimensions, and weight: Confirm from the applicable Rexroth documentation for this exact configuration.
- Condition and warranty: Seller-specific; request written confirmation for the exact unit.
Product Introduction
Bosch Rexroth Indramat MHD093A-035-PG0-BA (R911291332) is a size-093 MHD permanent-magnet synchronous servo motor for closed-loop industrial motion axes. Product references list natural-convection cooling, 12.0 Nm continuous torque at standstill, absolute digital feedback, a plain sealed shaft, and a 140/150 mm flange with a 130 mm centering diameter.
Match the complete type code before replacing an installed motor. In particular, verify the winding, feedback interface, mounting dimensions, shaft, and brake configuration; the PG0 suffix should not be treated as proof that a brake is supplied.

MHD093A-035-PG0-BA
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Motor will not start | Drive not enabled, supply issue, safety interlock, or drive fault | Possible | Read the drive fault history and verify the motor circuit against the machine wiring diagram with power isolated | Check drive status, interlocks, and supply before replacing the motor |
| Drive reports feedback fault | Feedback cable, connector, drive setup, or encoder problem | High | Inspect the feedback connector and cable; compare the configured feedback type with the exact MHD motor documentation | Confirm the drive supports this motor’s feedback interface before installing a replacement |
| Position reference is lost or inaccurate | Feedback setup, cable issue, or mechanical coupling problem | Possible | Review drive feedback diagnostics and inspect coupling alignment and cable connections | Check configuration and mechanical alignment before condemning the motor |
| Motor overheats | Excess load, poor airflow, high ambient temperature, or incorrect drive parameters | Relevant | Check load and motor-temperature data; confirm required clearances and cooling conditions from the machine documentation | This version is listed as naturally cooled; clear obstructions and verify the application duty before replacement. |
| Shaft or seal shows damage | Misalignment, contamination, impact, or bearing wear | High | With the axis safely isolated, inspect shaft condition, seal, and coupling per site procedure | Do not install a motor with damaged shaft or seal surfaces |
| Replacement does not fit or commission | Wrong type-code suffix, winding, mounting, or feedback configuration | High | Compare the full nameplate code, part number, flange, centering diameter, shaft, and connector arrangement | Stop commissioning until every configuration detail matches |
Support note: If the fault remains unresolved, contact technical support with the complete motor nameplate, drive model and fault history, connector photos, and the machine wiring diagram.
Frequently Asked Questions (FAQ)
What is the MHD093A-035-PG0-BA?
It is a Bosch Rexroth Indramat MHD-series permanent-magnet synchronous servo motor. Its Rexroth part number is R911291332.
What does the motor’s cooling designation mean?
Product references list this configuration as naturally cooled. Check installation clearances, ambient conditions, and duty requirements in the documentation for the machine and motor.
Does this model include a holding brake?
Do not assume it does. Confirm the brake configuration from the motor nameplate and seller’s written parts description before ordering.
Is it a direct replacement for another MHD093 motor?
Not necessarily. Match the full model code, winding, feedback, brake, shaft, and mounting dimensions. Similar frame size alone does not guarantee electrical or mechanical compatibility.
Will the absolute encoder retain position if I swap the motor?
The motor is listed with absolute position feedback, but whether the machine retains its reference after replacement depends on the drive and commissioning procedure. Back up parameters and follow the machine builder’s instructions before commissioning.
What condition is the motor in, and what warranty applies?
That depends on the seller and the specific unit. Request written confirmation of condition, serial number, test scope, warranty coverage, and return terms. Do not interpret a reseller warranty as OEM warranty coverage.
What should I verify before ordering?
Send the seller a clear nameplate photo and confirm the exact code MHD093A-035-PG0-BA / R911291332, winding, feedback interface, brake configuration, mounting dimensions, and condition.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626