Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Catalog number | OS9-GNI-C20L |
| Associated hardware part number | 902434 |
| Brand | Alcatel-Lucent |
| Platform | OmniSwitch 9000 modular chassis |
| Copper ports | 20 × RJ45, auto-negotiating 10Base-T / 100Base-TX |
| Copper-port upgrade | 1000Base-T available with OS9-C20L-UPG software license, one license per module |
| Fiber/SFP ports | 2 × SFP, 100/1000Base-X |
| SFP media | Requires compatible SFP transceivers; verify fiber type, wavelength, and distance |
| Chassis compatibility | OmniSwitch 9000-series chassis; installs in available NI slots |
| Hot-swap capability | Yes; module is hot-swappable |
| Typical power consumption | Less than 56 W |
| Operating temperature | 0 to 45°C (32 to 113°F) |
| Switching features | Layer 2 switching, QoS, security, and port-based egress shaping through OmniSwitch 9000 software |
| ASIC revision note | OS9-GNI-C20L with ASIC B2, part 902434, is supported in AOS 6.1.3.R01 and 6.1.5.R01; not supported in 6.1.1.R01 or 6.1.2.R03 |
| Physical form | Modular chassis line card |
The OS9-GNI-C20L provides 20 auto-sensing RJ45 ports plus 2 SFP ports for an OmniSwitch 9000 chassis. The copper ports ship as 10/100 Ethernet and can be upgraded to 1000Base-T only with the OS9-C20L-UPG license; the two SFP ports operate at 100/1000Base-X.
Product Introduction
The Alcatel-Lucent OS9-GNI-C20L is a hot-swappable network interface card for OmniSwitch 9000 modular chassis switches. It adds 20 RJ45 access ports and 2 SFP uplink ports, making it suitable for enterprise aggregation, wiring-closet expansion, and legacy OmniSwitch 9000 network maintenance.
Its main value in an existing installation is direct chassis compatibility and port-density continuity. The 20 copper ports are 10/100 by default; enabling Gigabit Ethernet on those ports requires the separate OS9-C20L-UPG license, so buyers must verify whether their network design requires 10/100 or licensed 1000Base-T operation.

OS9-GNI-C20L

OS9-GNI-C20L
Installation & Configuration Guide
Stage 1: Pre-Installation Preparation
Estimated time: 10 minutes.
- ⚠️ Confirm the OmniSwitch 9000 chassis is running an AOS release that supports the installed OS9-GNI-C20L ASIC revision. Part 902434 with ASIC B2 requires AOS 6.1.3.R01 or 6.1.5.R01 according to the release notes.
- Back up the running configuration using the chassis CLI or management interface.
- Record the target slot number, VLAN assignments, port descriptions, spanning-tree settings, link aggregation, and QoS configuration.
- Verify that the replacement card is OS9-GNI-C20L, not OS9-GNI-C24, OS9-GNI-U24, or OS9-GNI-P24.
- Confirm SFP transceiver compatibility and have labeled fiber patch cords available.
- Wear an ESD wrist strap and work at an ESD-safe bench or use a grounded chassis handle.
Stage 2: Removing the Old Line Card
Estimated time: 5–10 minutes.
- ⚠️ Although the card is hot-swappable, disable or administratively shut down its ports before removal if the network permits.
- Label every copper and fiber cable by chassis slot and physical port number.
- Disconnect the two SFP fiber links first, then remove copper Ethernet cables.
- Release the line-card captive screws or ejector mechanism.
- Pull the card straight out along the chassis guide rails.
- Inspect the chassis connector cavity, card guides, and replacement card edge connector for bent pins, debris, or damage.
⚠️ Keep the removed OS9-GNI-C20L until the replacement has passed link, VLAN, and redundancy testing.
Stage 3: Installing the New Line Card
Estimated time: 5 minutes.
- Verify the replacement card’s model label and hardware part number.
- Confirm the target slot is empty and compatible with a GNI-class network interface card.
- Align the card with the chassis guides and insert it firmly until the connector fully seats.
- Secure the captive screws or locking mechanism.
- Reinstall the labeled copper patch cords.
- Install the same SFP transceivers or verified equivalents, then reconnect the fiber links.
Self-checklist:
- Correct OS9-GNI-C20L model confirmed
- Chassis slot and connector fully seated
- Captive screws secured
- Copper and fiber cables labeled and connected
- SFP transceivers compatible with the installed fiber plant
Stage 4: Power-On & Testing
Estimated time: 10–15 minutes.
- Observe chassis and line-card status LEDs after insertion.
- Log in to the OmniSwitch CLI and confirm that the chassis recognizes the card in the expected slot.
- Verify the AOS software version and card status.
- Apply or restore the saved port configuration.
- Test each copper link for correct speed, duplex, VLAN membership, and Spanning Tree state.
- Test both SFP uplinks for optical link status, negotiated speed, and end-to-end connectivity.
- If 1000Base-T is required, confirm the OS9-C20L-UPG license is installed and active; without it, the RJ45 ports remain 10/100.
⚠️ If the card is not recognized, do not force reseating repeatedly. Check chassis compatibility, AOS release support, card part number, and connector seating first.
Frequently Asked Questions (FAQ)
Can I hot-swap the OS9-GNI-C20L?
Yes. Alcatel-Lucent designed OmniSwitch 9000 modules as hot-swappable, and this card can be replaced with the chassis powered. In production, administratively disable affected ports first to avoid unnecessary network disruption.
Are the 20 RJ45 ports Gigabit Ethernet?
Not by default. They are 10/100Base-T ports; 1000Base-T operation requires the OS9-C20L-UPG software upgrade license, with one license required per module.
Do the SFP ports support 1 Gbps only?
The two SFP ports support 100/1000Base-X. Actual capability depends on the installed SFP transceiver and the connected fiber plant.
Which OmniSwitch chassis accepts this card?
It is intended for Alcatel-Lucent OmniSwitch 9000-series modular chassis platforms. Confirm the exact chassis model and available NI slot type before ordering.
Is the OS9-GNI-C20L obsolete?
It is a legacy OmniSwitch 9000 line card. Alcatel-Lucent Enterprise still provides documentation and support pathways, but new-original availability is limited; tested refurbished or surplus units are common in the secondary market.
Will replacing the card erase my switch configuration?
No. The configuration resides in the chassis control module and its storage, not on the GNI line card. Back up the configuration anyway before the replacement.
Why do prices vary so much for this module?
Condition drives the price: new sealed surplus, tested refurbished, or exchange units command different prices. Also verify whether SFP transceivers, licenses, and warranty are included; those items materially affect total replacement cost.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626