Description
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Motor family | MP-Series MPL low-inertia servo |
| Voltage class | 460 V AC |
| Frame size | 165 mm |
| Magnet stack length | 101.6 mm (4.0 in.) |
| Rated speed | 4,000 rpm |
| Rated output power | 5.4 kW |
| Continuous stall torque | 19.4 N·m (172 lb-in) |
| Peak stall torque | Approximately 47.4 N·m (420 lb-in), as reported by distributor data |
| Continuous stall current | 20.5 A (0-peak), as reported by distributor data |
| Encoder | Single-turn high-resolution absolute encoder |
| Encoder protocol | Hiperface |
| Feedback resolution description | 1024 sin/cos, per distributor listing |
| Brake | 24 V DC |
| Shaft configuration | Keyed shaft, no shaft seal |
| Connector style | Circular bayonet connector, facing shaft |
| Mounting flange | IEC metric |
| Protection | Standard protection; verify the exact IP rating for the unit |
Catalog suffix .0023 |
Not independently verified in the public documentation reviewed |
The motor specifications above are for the base catalog number MPL-B540K-SJ24AA. Rockwell’s MP-Series documentation describes the relevant motor family, connector, encoder, brake, and installation requirements.
Product Introduction
The Allen-Bradley MPL-B540K-SJ24AA is a low-inertia brushless AC servo motor designed for industrial motion-control systems that require controlled speed, torque, and position. Its 5.4 kW rating, 4,000 rpm rated speed, single-turn Hiperface encoder, and integral 24 V DC brake make it suitable for compatible servo-driven machinery. Before replacing an installed motor, verify the drive’s voltage class, feedback compatibility, motor cabling, mechanical dimensions, and brake requirements.
Installation and Configuration Guide
Stage 1: Pre-Installation Checks
- Confirm the motor nameplate, complete catalog number, series, and any suffixes.
- Verify that the servo drive supports the motor’s 460 V class and Hiperface feedback.
- Check the mounting flange, shaft key, coupling dimensions, and allowable shaft loads.
- Confirm the correct power, feedback, and brake cables.
- Review the drive and motor manuals before disconnecting the existing unit.
Stage 2: Remove the Existing Motor
- Stop the machine using the approved shutdown procedure and isolate drive power.
- Apply lockout/tagout and verify that hazardous energy has been removed.
- Support the motor and driven load before removing mounting hardware.
- Mark cable connections and record the original drive configuration.
- Remove the coupling or pulley using appropriate tools; do not strike the motor shaft.
Stage 3: Install the Replacement
- Inspect the motor shaft, keyway, mounting pilot, and flange for damage.
- Align the motor carefully with the driven equipment.
- Tighten mounting fasteners to the values specified in the applicable installation manual.
- Connect motor power, encoder feedback, and the 24 V DC brake using compatible cables.
- Separate feedback wiring from motor power cables and ground the equipment according to Rockwell’s wiring guidance.
Stage 4: Configure and Commission
- Verify the motor catalog number and feedback type in the servo drive configuration.
- Check motor direction, encoder feedback, brake operation, and applicable drive parameters.
- Perform initial testing at reduced speed and with the machine in a safe state.
- Confirm that the motor reaches the required speed and responds correctly to position and torque commands.
- Check for abnormal noise, vibration, overheating, or drive faults before returning the machine to production.
Stage 5: Important Installation Warnings
- Never connect or disconnect motor power or feedback cables while the servo drive is energized. Unexpected motion or electrical arcing may occur.Manualzz
- Do not strike the shaft, coupling, or pulley during installation; impact can damage the bearings and feedback device.
- Verify axial and radial shaft loads against the manufacturer’s limits.
- Do not assume that a motor with the same power and speed is interchangeable if the encoder, brake, connector, or mounting configuration differs.

MPL-B540K-SJ24AA.0023

MPL-B540K-SJ24AA.0023
Frequently Asked Questions
Q1: What is the MPL-B540K-SJ24AA used for?
It is an industrial AC servo motor used in compatible servo motion-control systems for speed, torque, and position control.
Q2: What are its rated power and speed?
Distributor technical listings specify 5.4 kW and 4,000 rpm for the base catalog number.
Q3: Does this motor include a holding brake?
Yes. The listed configuration includes a 24 V DC brake. Confirm the brake wiring and drive-control requirements before commissioning.
Q4: Which feedback system does it use?
The listed motor uses a single-turn high-resolution absolute encoder with Hiperface protocol. The replacement servo drive must support the applicable feedback system.
Q5: Can I replace it with another MPL-B540K motor?
Not solely on the basis of the shared family name. Other versions may use different encoder types, connector styles, shaft configurations, or brake options. Match the complete catalog number and verify drive compatibility.
Q6: Is MPL-B540K-SJ24AA.0023 the complete manufacturer part number?
The base model MPL-B540K-SJ24AA is documented in distributor listings. I could not independently verify the additional .0023 suffix as a separate public catalog designation. Check the physical nameplate or manufacturer records before using that suffix for purchasing or replacement identification.
Q7: What should buyers verify before ordering?
Confirm the nameplate and suffix, motor condition, encoder type, brake function, shaft and flange dimensions, connector condition, and available inspection records. Ask the seller to specify whether the motor is new, surplus, or refurbished and to state the applicable warranty terms.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626