Sale!

Alstom MMLG01 Standard Test Block

  • Model: MMLG01
  • Brand: Alstom (now GE Grid Solutions / GE Vernova)
  • Series: Midos / MMLG series
  • Core Function: Isolation and secondary injection testing of protection schemes
  • Product Type: Standard Test Block
  • Key Specs: 14 circuits; 20 A continuous; make-before-break CT shorting; used with MMLB01 plug
  • Condition: New Original / New Surplus
Categories: , , , , Brand:

Description

. Key Technical Specifications

  • Number of circuits: 14 independent circuits (paired rear terminals)
  • Current rating: 20 A continuous / 400 A for 1 s (MMLG01 / MMLB01 combination)
  • Voltage rating: 300 V AC or DC continuous
  • Contact design: Spring-loaded normally closed contacts; open on insertion of MMLB01 multi-finger test plug
  • Safety feature: Automatic shorting of CT secondaries (make-before-break) before isolation
  • Special terminals: Terminals 13 and 14 – short contact fingers; not for CT connections; used for trip-circuit isolation via cover probe
  • Mounting: Flush panel / modular case, mounts adjacent to Midos relays
  • Compatible test plugs: MMLB01 (multi-finger), MMLB02 (single-finger)
  • Operating temperature: Typically –25 °C to +55 °C
  • Insulation: 1 kV rms for 1 minute between finger contacts (typical)
  • Note: Exact dimensional drawings, weight, and full type-test data should be confirmed from the GE/Alstom technical publication before installation.

4. Product Introduction

The Alstom MMLG01 is a standard test block from the Midos range, designed for safe monitoring, isolation, and secondary injection testing of power-system protection schemes. It mounts adjacent to modular relays and carries 14 circuits that remain closed under normal service.

When the matching MMLB01 multi-finger test plug is inserted, the internal contacts open cleanly, allowing injection and measurement without disturbing permanent wiring. The design incorporates make-before-break shorting for current-transformer circuits, preventing open-circuit CT hazards during testing.

MMLG01

MMLG01

MMLG01

MMLG01

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Relay trips when test-block cover is removed Trip circuit not routed through terminals 13–14 ✅ High Verify DC auxiliary / trip supply is wired through terminals 13 and 14 Correct wiring so cover removal isolates the trip circuit
CT circuit remains open or high voltage appears Failed make-before-break shorting contacts ✅ High Measure continuity across CT terminals before and during plug insertion Replace the test block; never operate with open CT secondaries
No continuity through a circuit with plug removed Contaminated or worn spring contacts ✅ Medium Check resistance of each closed contact pair with a low-ohm meter Clean or replace the block if resistance is elevated
Test plug will not insert fully Misaligned fingers or damaged guide ✅ Medium Inspect plug and block for bent contacts or debris Use only genuine MMLB01 plug; do not force insertion
Intermittent readings during secondary injection Poor contact pressure or oxidized sockets ✅ Medium Wiggle test leads and re-measure; check 4 mm socket condition Clean sockets and verify plug finger integrity
Cover will not seat or probe fails to engage Incorrect cover orientation or broken probe ✅ High Confirm cover orientation marks and probe length Fit correct cover; never leave cover off in service

If diagnostics remain unclear, photograph the block, wiring, and any labels, then contact technical support with the full model string.

6. Frequently Asked Questions (FAQ)

Q: What is the primary purpose of the Alstom MMLG01?
A: It provides a safe interface for isolating a protection relay or scheme and performing secondary injection tests without disconnecting permanent wiring. It is not a protection relay itself.

Q: Which test plug do I need?
A: Use the MMLB01 multi-finger test plug for simultaneous access to all circuits. The MMLB02 single-finger plug is available for monitoring individual circuits.

Q: Can terminals 13 and 14 be used for CT connections?
A: No. These terminals have short contact fingers and are intended for the auxiliary DC / trip-circuit isolation function. Using them for CTs creates a safety hazard.

Q: Is the MMLG01 still supported?
A: The original Alstom version is discontinued by the manufacturer, but New Surplus and equivalent GE-branded units (often with updated livery) remain available for maintenance of existing installations.

Q: Does the block short CT secondaries automatically?
A: Yes. The design provides make-before-break shorting so that CT circuits are shorted before they are isolated from the relay when the test plug is inserted.

Q: Can I leave the cover off after testing?
A: No. The cover must be correctly replaced and oriented. It provides both electrical isolation of the trip circuit (via the internal probe) and protection against accidental contact.

Q: What condition and warranty apply to units you supply?
A: We supply New Original / New Surplus stock. Each unit is inspected for contact integrity and mechanical condition. Standard coverage is a 1-year warranty against defects. Provide the full model MMLG01 (and any suffix if present) when ordering or requesting support.