WhatsApp: +86 16626708626
Email: 
Phone: +86 16626708626Description
Key Technical Specifications
- Model: 330780-50-05
- Manufacturer: Bently Nevada
- Product family: 3300 XL Proximitor Sensor
- Sensor size: 11 mm
- System length: 5 m
- Mounting style: DIN rail mount
- Primary use: Shaft displacement and vibration measurement
- Compatibility: 3300 XL 11 mm transducer system
- Output: Proximity transducer signal to monitor input
- Installation note: Verify probe and extension cable match the 11 mm system
Product Introduction
Bently Nevada 330780-50-05 is a 3300 XL 11 mm Proximitor Sensor used for shaft displacement and vibration monitoring on rotating machinery. It is part of the 3300 XL proximity transducer system and supports machine protection setups that depend on accurate gap and vibration signals.
This sensor is commonly chosen for retrofit and replacement work where the installed machine already uses a Bently 3300 XL 11 mm architecture. The DIN mount and 5 m system length make it a straightforward fit when the original wiring and probe family are matched correctly.
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| No output signal | No power, open loop, or failed sensor | ✅ High | Measure supply at the sensor terminals and check loop continuity | Verify power and wiring before replacing the sensor |
| Offset voltage out of range | Probe gap set wrong or sensor not matched to probe | ✅ High | Check the air gap and compare output to the original installed value | Re-set the probe gap and confirm system calibration |
| Signal noisy or unstable | Poor grounding, loose DIN mount, or cable issue | ✅ High | Inspect shield termination and tighten mounting hardware | Fix grounding and cable routing before condemning the unit |
| Reading drops at vibration | Connector or cable intermittency | ✅ High | Wiggle-test the cable and monitor output on a scope or meter | Replace damaged cable or connector set |
| Monitor alarm after swap | Wrong system length or incorrect probe family | ✅ High | Confirm probe type, extension cable length, and sensor model | Match the full 3300 XL transducer chain exactly |
| Sensor seems fine but machine trips | Monitor configuration issue | ❌ Low | Check alarm setpoints and monitor scaling | Review monitor settings before replacing hardware |
If the fault stays unclear, contact technical support with photos of the label, probe, cable, mounting, and diagnostic trend data.
- 330780-50-05
Frequently Asked Questions (FAQ)
Q: Is 330780-50-05 the probe or the sensor?
A: It is the Proximitor sensor, not the probe tip. The probe, extension cable, and sensor have to match as a system.
Q: Is this a direct replacement for any 3300 XL 11 mm setup?
A: Usually yes, but only if the probe family, cable length, and mounting style match the original installation. Always confirm the full transducer chain before ordering.
Q: Can I use it with a different probe length?
A: Not without checking compatibility. To be honest, that is where people get into trouble. Mismatched system lengths can distort the output and trigger false alarms.
Q: What is the biggest installation mistake?
A: Swapping the sensor without checking the probe family and extension cable length. Take a photo of the old setup before removal and mirror the exact configuration.
Q: Is it hot-swappable?
A: I would not treat it as casually hot-swappable. Follow site lockout and machine protection procedures before changing it, because a bad swap can cause nuisance trips.
Q: Why is this part often sold as surplus?
A: Because it is a legacy industrial part that many plants keep as a spare rather than buying direct from factory channels. Surplus pricing is usually lower, but traceability and test records matter.
Q: What should I ask the seller for?
A: Ask for clear label photos, system length confirmation, connector photos, and any test evidence. For critical spares, demand serial traceability and a short functional warranty.
