Description
Key Technical Specifications
| Parameter | Specification / Value |
| Model Number | LB444W / LB 444 W |
| Manufacturer | Berthold Technologies GmbH & Co. KG |
| Measurement Principle | Microwave absorption / Radiometric concentration & moisture evaluation |
| Power Supply Input | 115 V AC / 230 V AC (±10%, 50/60 Hz) or 24 V DC |
| Power Consumption | Approx. 30 VA |
| Analog Outputs | 2x 0/4–20 mA (galvanically isolated, max. 500 Ω load) |
| Digital Output / Relays | 4x SPDT relay outputs (configurable for system fault, min/max threshold alarms) |
| Communication Interface | HART Protocol, RS-232 / RS-485 serial interface |
| Display & User Interface | Illuminated LCD graphics screen with membrane keypad |
| Enclosure Rating | IP65 (NEMA 4X) wall-mount housing |
| Operating Temperature | −20 °C to +60 °C (−4 °F to +140 °F) |
| Unit Weight | 6.2 kg (13.7 lbs) |
Product Introduction & Supply Chain Strategy
The Berthold LB444W Micro-Gamma is an industrial-grade process evaluation unit engineered for real-time, non-contact measurement of water content, moisture percentage, dry substance, and suspension concentration. Utilizing high-precision microwave attenuation and phase-shift evaluation, it delivers continuous online process monitoring across slurries, bulk materials, chemical suspensions, and food production pipelines without contacting the medium.
Because Berthold has updated its process instrumentation portfolio to newer transmitter platforms (such as the Micro-GTR and LB 568 series), sourcing original New Surplus LB444W units is critical for facilities relying on validated measurement loops. Replacing an existing unit with an entirely new platform requires costly pipe spool modifications, recalculation of calibration curves, and DCS re-integration. Utilizing New Surplus inventory preserves exact physical mounting and signal compatibility while eliminating the severe risks of second-hand units—such as degraded microwave sensor front-ends, dried-out power supply capacitors, and drift prone ADC circuits. Maintaining 1–2 New Surplus units as strategic buffer stock ensures zero measurement outage during production runs.
Installation & Configuration Guide
High Voltage & Process Interlock Hazard
Ensure main power feeds (115/230 V AC or 24 V DC) are isolated using strict Lock-Out/Tag-Out (LOTO) procedures before opening the IP65 enclosure. If the transmitter connects to radioactive source detectors, ensure source containers are locked in the OFF/Shielded position prior to servicing adjacent cabling.
1.Pre-Installation & Safety Setup:5 mins.
Execute LOTO on the cabinet supply breaker. Wear a grounded ESD wrist strap before touching internal terminal boards. Record wiring positions for power, 4–20 mA loop outputs, and sensor horn/antenna coaxial feeds.
2.Demounting Outgoing Controller:10 mins.
Disconnect terminal strips for signal I/O, relay contacts, and power. Unplug high-frequency coaxial microwave cables carefully without straining connectors. Loosen wall-mounting bracket hardware and lift the unit clear.
3.Mounting & Cable Termination:10 mins.
Mount the new LB444W onto the wall-mount bracket using M6 hardware. Insert cables through IP65 cable glands. Re-terminate high-frequency microwave sensor cables, 4–20 mA current loops, and mains power wires according to the terminal diagram.
4.Power-On & Calibration Transfer:15 mins.
Restore power and verify LCD initialization. Enter system setup via the keypad to verify attenuation parameters, product calibration tables, and 4–20 mA span values. Perform a dry-run baseline zero check to confirm sensor resonance before placing the unit in AUTO control.
Verification: The display must show a stable moisture/density readout without error codes (e.g., “E01: Microwave Signal Loss” or “E04: ADC Saturation”), and 4–20 mA outputs must match the process variable on the central DCS console.

LB444W

LB444W
Firmware/Software Versions & Upgrade Notes
- System Compatibility: Compatible with standard Berthold microwave horn antennas, transmission sensors, and radiometric detector arrays designed for the LB444 series.
- Calibration Data Transfer: Calibration coefficients (slope, offset, temperature compensation factors) reside in internal EEPROM memory. When replacing an LB444W unit, manually transcribe or transfer through HART/RS-232 the specific product calibration data from the old unit to maintain measurement accuracy.
- Communication Interface Note: Ensure the onboard HART modem or RS-485 termination resistors are enabled via internal DIP switches if the unit is installed at the end of a serial communication multidrop network.
Frequently Asked Questions (FAQ)
Is this Berthold LB444W evaluation unit factory original new or refurbished?
This product is Brand New Surplus. It is not a pulled unit, second-hand monitor, or refurbished assembly. It features pristine internal circuit boards, factory-original power supplies, and un-degraded microwave signal front-ends.
Why should our plant avoid buying used or refurbished Berthold evaluation units?
Refurbished process monitors from aggressive plant environments often suffer from environmental seal degradation, moisture ingress in terminal compartments, and thermal drift on analog converter components. In continuous process lines, an inaccurate moisture reading can lead to out-of-spec product batches costing exponentially more than the price of a genuine New Surplus transmitter.
Can the LB444W measure water content in both liquids and bulk solids?
Yes. Depending on the connected sensor configuration (e.g., flow-through cell, horn antenna over a conveyor belt, or insertion probe), the LB444W evaluates moisture across liquids, slurries, powders, and granulates.
Is re-calibration required after swapping the transmitter unit?
Yes. While the new unit operates with factory precision, you must enter the product-specific calibration matrix (attenuation/phase shift constants versus laboratory moisture samples) stored from your existing process line setup to ensure true concentration accuracy.
What warranty covers this New Surplus LB444W unit?
Every New Surplus Berthold LB444W transmitter is backed by a standard 12-Month Replacement Warranty. Prior to dispatch, each unit passes rigorous quality control inspections—including power supply stability checks, display/keypad validation, and analog current loop accuracy verification.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626