Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Motor type | Digital synchronous AC servo motor, electronic commutation (brushless) |
| Motor size / length code | MKD 025 / B |
| Standstill torque (continuous) | 0.9 Nm at standstill |
| Rated speed / Max speed | 2,000 rpm rated · up to 9,000 rpm maximum |
| Rated voltage | 94.7 V (at 60 K overtemperature) / 98.4 V (at 100 K) |
| Continuous current | 5.1 A |
| Winding code | 144 |
| Feedback system | Integrated motor feedback, multiturn absolute encoder |
| Holding brake | 1 Nm holding brake (24 V DC brake coil) |
| Shaft design | Plain shaft with shaft sealing ring |
| Flange / centering diameter | 54 mm / 40 mm |
| Protection rating | IP65 |
| Connector orientation | Power and encoder connectors rotatable 270° |
| Weight | Approx. 2 kg |
| Ambient temperature range | 0 to +40 °C |
| Drive compatibility | Rexroth IndraDrive, HCS, ECOdrive, DIAX family converters |
| Insulation class | Per MKD standard (EN 60034-1) |
Verify precise mounting, brake, and feedback details against the Rexroth MKD Project Planning Manual before ordering. The “-UN” and “-KN” suffixes differ in electrical connection design — they are not always drop-in interchangeable on the same cable set.
Product Introduction
The MKD025B-144-KG1-UN is a compact brushless synchronous servo motor from Bosch Rexroth’s Indramat MKD series, built for packaging lines, CNC auxiliary axes, food processing, textiles, and general automation. Its low-inertia rotor and electronic commutation handle high-cycle start-stop duty without brush wear.
Engineers choose this frame for one reason: it’s a workhorse. The 54 mm flange fits tight machine footprints, the multiturn absolute feedback eliminates homing runs after power loss, and the 1 Nm holding brake locks vertical axes during e-stops. It pairs directly with IndraDrive-era converters, which is exactly why plants keep buying this obsolete unit instead of re-engineering an entire axis around a newer motor line.

MKD025B-144-KG1-UN

MKD025B-144-KG1-UN
Installation & Configuration Guide
Stage 1: Pre-Installation Preparation (~10 min)
- ⚠️ Safety First: Notify operations of the downtime window. Drive the axis to a safe position. Lock out/tag out the drive cabinet. Kill the 24 V brake circuit separately — vertical axes will drop when the brake releases. Wait 5 minutes for DC bus capacitors to discharge, then verify the bus reads below 60 V DC with a meter.
- Tools Required: Grounded ESD wrist strap, multimeter (a Fluke 115 or equivalent), hex key set, torque wrench, thread-locker, cable labels, smartphone for photos.
- Data Backup: In IndraWorks/DriveTop, read the drive’s motor configuration block and save it. Photograph the connector orientation and the cable entry position. If the axis uses a vertical load, note the brake control wiring.
Stage 2: Removing the Old Motor (~10 min)
- Verify the drive is in a safe torque-off state and the DC bus is dead.
- Disconnect the power connector, encoder connector, and brake connector. Label all three — they look similar and miswiring the brake into the encoder line will cook the feedback board.
- Loosen the coupling or release the clamping set. Never force a friction-locked shaft-hub connection; use a puller if it’s seized.
- Unbolt the flange (4 bolts) and withdraw the motor straight out.
- Inspect the mounting face for burrs and check the shaft sealing ring on the new motor for damage in transit.
- ⚠️ Keep the old motor on the bench until the replacement runs clean. You may need its connector pinout as a reference.
Stage 3: Installing the New Motor (~10 min)
- ESD strap on before you touch the connector pins. Verify the nameplate reads MKD025B-144-KG1-UN exactly — the KG0 variant has no brake and will not hold a vertical axis.
- Rotate the connectors to match the cable entry direction of the old unit (270° range) before mounting. Doing this after mounting on a tight machine is miserable.
- Mount to the flange, torque bolts evenly in a cross pattern to the value in the MKD manual. Apply thread-locker.
- Align the coupling; check shaft runout with a dial indicator if you have precision requirements.
- Reconnect power, feedback, and brake connectors. Seat them fully until the locking tabs engage.
- Self-Checklist: [ ] Nameplate matches, [ ] Connectors locked, [ ] Coupling aligned, [ ] Brake lead separated from feedback lead.
Stage 4: Power-Up & Testing (~10 min)
- Restore cabinet power with the drive in disabled state. Brake circuit should energize and audibly release.
- Enable the drive. On the IndraDrive, check for motor feedback errors in the diagnostic block.
- Because this motor carries a multiturn absolute encoder in the connector head, the drive should read position immediately — no homing required. If the drive demands a homing run, the feedback data didn’t transfer: power-cycle the drive with the encoder connected.
- Jog the axis at 10% speed first. Listen for bearing noise and verify rotation direction.
- Run a slow full-travel move, then restore the application program and release to production.
- ⚠️ Troubleshooting Note: If the drive throws an encoder error immediately, power off completely before reseating the feedback connector — hot-plugging the encoder line can damage the feedback electronics. If the motor runs rough, verify you didn’t swap any two motor phase leads.
Frequently Asked Questions (FAQ)
Q1: Can I hot-swap this motor under power?
No. The DC bus on IndraDrive converters holds several hundred volts after shutdown, and the motor connectors are not rated for disconnect under load. Kill the drive power, wait for the bus to discharge below 60 V, then disconnect. On vertical axes, lock the load mechanically first — the holding brake only holds 1 Nm, and it releases the moment the 24 V circuit drops.
Q2: Is this model obsolete? Is what you’re selling actually new?
Yes, the MKD series is discontinued — Rexroth moved successors into the MSM and MKS lines. What we sell is New Original / New Surplus: genuine Rexroth stock, factory packaging, never energized in service. We document the source (OEM packing lists, customs declarations) and verify serial numbers against Rexroth’s database as an anti-counterfeit check. Photos of the exact unit and serial number are available before you commit.
Q3: What’s the direct replacement if this exact unit is out of stock?
Within the MKD family, check MKD025B-144-KG1-KN — same motor, different connection housing, which may require a cable set change. For new machine designs, the MSM series covers this torque class, but it needs a modern IndraDrive Cs/Ms converter and new cables. It’s a redesign, not a swap. Call us with your drive firmware version before cross-ordering anything.
Q4: Will I lose my position data or program when I swap the motor?
No. The drive stores the motion logic and parameters, not the motor. This motor’s multiturn absolute encoder is powered through the feedback connector with its own data memory, so position is retained. One caveat: after the swap, power the drive up once with the encoder connected before enabling the axis — the drive needs to read the new motor’s data memory on that first cycle.
Q5: Why is your price lower than Rexroth’s original list price?
Because Rexroth no longer makes it. Our stock comes from liquidated projects, OEM spares programs, and factory overruns purchased years ago. We’re not an authorized Rexroth distributor, and we say so plainly: warranty is ours, 12 months, not Rexroth’s. The trade-off is price and availability today versus factory support on a motor line that no longer exists.
Q6: Does the holding brake need a separate power supply?
Yes. The brake runs on 24 V DC and must be wired through the drive’s brake control output, not a hard-wired supply. Wire it direct and you lose the controlled brake release — the axis stops hard on every disable, which hammers the coupling and gearbox. And keep the brake leads physically separated from the encoder cable; induced voltage on the feedback line causes phantom position faults that will eat a full afternoon to find.
Q7: What quality checks do you run before shipping?
Every unit passes an inbound inspection (serial verification, anti-counterfeit checks, visual and accessory audit), then a live bench test on a genuine IndraDrive rack: power-up, encoder handshake, brake release/engage test, and a continuous-run burn-in exceeding 24 hours with thermal monitoring. We log the results in a Test Report and repackage in ESD bagging with a QC Passed label and date. Test videos and photos are available on request. We won’t tell you it’s failure-proof — we’ll tell you exactly what we verified.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626