Sale!

Bosch Rexroth MKD071B-061-KP0-KN AC Servo Motor

  • Model: MKD071B-061-KP0-KN
  • Brand: Bosch Rexroth / Indramat
  • Series: MKD synchronous servo motors
  • Core Function: Closed-loop AC servo motion control
  • Product Type: Permanent-magnet synchronous servo motor
  • Key Specs: 8.0 Nm continuous standstill torque; 11.2 A continuous current; resolver feedback
  • Condition: New Original / New Surplus
  • ⚠️ Obsolete Model – Limited Stock Available
Categories: , , , SKU: MKD071B-061-KP0-KN Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer Bosch Rexroth Indramat
Model MKD071B-061-KP0-KN
OEM ordering number R911262599
Motor type Three-phase permanent-magnet synchronous servo motor
Frame size / length 071 / B
Winding code 061
Continuous standstill torque 8.0 Nm at 60 K temperature rise
Continuous standstill torque, 100 K rise 9.0 Nm
Continuous standstill current 11.2 A
Peak current 50.4 A
Peak stall torque 36 Nm
Torque constant 0.77 Nm/A
Winding resistance 1.45 Ω
Winding inductance 7.2 mH
Nominal characteristic speed 4,500 rpm
Feedback Resolver, relative position feedback
Holding brake None
Shaft Keyed solid shaft, DIN 6885-1, with radial shaft sealing ring
Flange 115 mm square flange
Centering diameter 95 mm
Connection direction Side B
Cooling Natural convection
Ingress protection IP65 motor housing; IP54 feedback connector
Insulation class F
Ambient temperature 0 to +40°C
Storage temperature −25 to +70°C
Weight Approximately 8.7 kg

The electrical and mechanical values are based on published MKD project-planning data and verified listings for this exact type code.

 

Product Introduction

The Bosch Rexroth MKD071B-061-KP0-KN is a brushless, permanent-magnet synchronous servo motor for machine-tool feeds, packaging machinery, printing lines, and general motion-control axes. Its 061 winding delivers 8.0 Nm continuous standstill torque and 36 Nm peak torque, with a 4,500 rpm nominal characteristic speed.

This KP0-KN configuration uses resolver feedback, a keyed shaft, and no holding brake. That makes it a direct fit for horizontal axes where the drive performs commutation and position control, but it is not a substitute for a brake-equipped KP1/KP3 motor on a vertical axis.

MKD071B-061-KP0-KN

MKD071B-061-KP0-KN

MKD071B-061-KP0-KN

MKD071B-061-KP0-KN

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Drive reports feedback or commutation fault Damaged resolver cable, loose connector, broken shield, or resolver failure ✅ High Inspect the feedback connector and cable; check shield continuity and connector seating; substitute a known-good cable Repair or replace the feedback cable first; replace the motor only if the alarm follows the motor
Motor will not produce torque Incorrect drive motor type code, phase sequence error, or power-cable fault ✅ High Confirm the drive motor type is MKD071B-061-KP0-KN; measure U/V/W continuity and insulation resistance to ground Correct drive configuration and power wiring before replacing the motor
Motor overheats Excessive duty cycle, mechanical binding, blocked cooling surface, or high ambient temperature ⚠️ Medium Measure housing temperature; review drive torque/current trend; check for coupling drag or contaminated cooling fins Reduce load or duty cycle, clean cooling surfaces, and verify free mechanical travel
Position error or unstable axis Coupling misalignment, loose mechanics, gain tuning, or feedback noise ⚠️ Medium Check coupling runout and flange bolts; observe following error in the drive diagnostics Correct mechanical alignment and cable shielding before changing drive gains
Motor runs but has poor low-speed smoothness Incorrect commutation angle, resolver signal issue, or mechanical cogging/load disturbance ✅ High Run the drive’s commutation/encoder diagnostic; compare behavior with the motor uncoupled if safe Recommission commutation and verify feedback signals; do not replace the motor first
Unexpected axis movement after power loss No holding brake installed in this KP0 configuration ✅ High Check whether the axis is vertical or back-drivable; inspect counterbalance or mechanical brake Use an external mechanical brake or select a KP1/KP3 brake-equipped variant for vertical loads
Bearing noise or vibration Bearing wear, shaft-load overload, or coupling misalignment ⚠️ Medium Rotate the shaft with power removed; inspect radial/axial play and listen at the bearing end Correct alignment and shaft loading; replace the motor if bearing damage is confirmed

If the alarm persists, send the Rexroth drive diagnostic list, motor nameplate photo, power and feedback cable part numbers, and a short video of the fault to technical support before ordering.

 

Frequently Asked Questions

Can I hot-swap the MKD071B-061-KP0-KN?
No. Disable the servo drive, remove mains and 24 V DC control power, and allow the DC bus to discharge before disconnecting the power or resolver cables. This motor has no holding brake, so secure any movable load before shutdown.

Does this motor include a holding brake?
No. The KP0 suffix means the motor is supplied without a holding brake. Do not use it as a direct replacement for a KP1 or KP3 brake-equipped motor on a vertical axis unless an external brake is already installed.

Is the resolver absolute or incremental?
This KN configuration uses resolver feedback for relative position and commutation. It does not provide the integrated multiturn absolute encoder found on KG1 versions.

Can I replace it with an MKD071B-061-KP1-KN?
Not without reviewing the application. The KP1 variant adds a holding brake, changes the connector arrangement, and may require different brake-supply wiring and drive configuration. The 071B frame and 061 winding match, but the complete type code must be verified.

Which Rexroth drives are compatible?
MKD motors are used with Rexroth Indramat DDS, DKS, DKC, HDS, and HDD servo drive families. Confirm that the installed drive supports the 061 winding and resolver feedback before ordering.

Why does the motor have two torque ratings?
The 8.0 Nm rating applies to a 60 K winding temperature rise; 9.0 Nm applies to a 100 K rise. Use the 60 K value for continuous-duty sizing unless your thermal design explicitly permits the higher winding temperature.

What condition is this motor supplied in?
This is New Original / New Surplus stock, not used or refurbished. Each unit is inspected, function-tested, and packed in ESD-safe packaging with a test report; photos and test documentation are available on request.