Sale!

Bosch Rexroth MKD090B-047-GP0-KN AC Servo Motor

  • Model: MKD090B-047-GP0-KN
  • Brand: Bosch Rexroth / Indramat
  • Series: MKD synchronous servo motors
  • Core Function: Closed-loop AC servo motion control
  • Product Type: Permanent-magnet synchronous servo motor
  • Key Specs: 12.0 Nm continuous standstill torque; 16.5 A continuous current; 5,000 rpm maximum speed
  • Condition: New Original / New Surplus
  • ⚠️ Obsolete Model – Limited Stock Available
Categories: , , , , SKU: MKD090B-047-GP0-KN Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer Bosch Rexroth Indramat
Model MKD090B-047-GP0-KN
OEM ordering number R911263529
Motor type Three-phase permanent-magnet synchronous servo motor
Frame size / length 090 / B
Winding code 047
Continuous standstill torque 12.0 Nm at 60 K temperature rise
Continuous standstill torque, 100 K rise 14.0 Nm
Continuous standstill current 16.5 A
Peak current 59.4 A
Peak stall torque 45 Nm
Maximum speed 5,000 rpm
Rated speed 3,500 rpm
Rated torque 9.9 Nm
Rated voltage 351 V
Torque constant 0.73 Nm/A
Winding resistance 0.69 Ω
Winding inductance 10.1 mH
Feedback Resolver, relative position feedback
Holding brake None
Shaft Keyed shaft per DIN 6885-1 with shaft sealing ring
Flange size 140 mm
Centering diameter 110 mm
Connection Connection box, Side B
Cooling Natural convection
Ingress protection IP65 motor housing; IP54 feedback connector
Insulation class F
Ambient temperature 0 to +40°C
Storage temperature −25 to +70°C
Weight 14 kg

The values above are based on the published MKD project-planning data and supplier specifications for this exact type code.

 

Product Introduction

The Bosch Rexroth MKD090B-047-GP0-KN is a brushless permanent-magnet synchronous servo motor for machine-tool axes, packaging equipment, printing machinery, and high-dynamic positioning applications. Its 047 winding delivers 12.0 Nm continuous standstill torque, 45 Nm peak torque, and up to 5,000 rpm.

The GP0-KN configuration uses resolver feedback, a keyed sealed shaft, and no holding brake. It is a strong fit for horizontal or mechanically braked axes, but it is not a direct replacement for a GP1 brake-equipped motor on a vertical load without adding external braking.

MKD090B-047-GP0-KN

MKD090B-047-GP0-KN

MKD090B-047-GP0-KN

MKD090B-047-GP0-KN

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Drive reports resolver or feedback fault Damaged feedback cable, loose connector, broken shield, or resolver failure ✅ High Inspect and reseat the feedback connector; check cable continuity and shield termination; substitute a known-good cable Replace the cable first; replace the motor only if the fault follows the motor
Motor will not develop torque Incorrect drive motor type code, phase wiring error, or damaged power cable ✅ High Verify the drive motor type is MKD090B-047-GP0-KN; measure U/V/W continuity and insulation to ground Correct the drive configuration and power wiring before condemning the motor
Motor overheats or trips thermal protection Excessive duty cycle, blocked cooling, mechanical binding, or high ambient temperature ⚠️ Medium Measure housing temperature; review drive current/torque trend; inspect coupling and load for drag Reduce duty cycle or load, clean cooling surfaces, and verify free mechanical travel
Position error or unstable operation Coupling misalignment, loose mounting, feedback noise, or incorrect drive tuning ⚠️ Medium Check flange bolts and coupling runout; review following error and diagnostics in the drive Correct mechanics and shielding before changing servo gains
Motor runs roughly at low speed Incorrect commutation angle, resolver signal issue, or mechanical disturbance ✅ High Run the drive’s commutation/feedback diagnostic; test uncoupled only with the load safely secured Recommission commutation and verify resolver signals; do not replace the motor first
Unexpected movement after power loss No holding brake in this GP0 configuration ✅ High Check whether the axis is vertical or back-drivable; inspect external brake or counterbalance Use an external mechanical brake or specify a GP1 brake-equipped variant for vertical loads
Bearing noise or excessive vibration Bearing wear, shaft overload, or misalignment ⚠️ Medium Rotate the shaft with power removed; check radial/axial play and listen at the bearing end Correct alignment and shaft loading; replace the motor if bearing damage is confirmed

If the fault remains, send the Rexroth drive diagnostic list, motor nameplate photo, cable part numbers, and a short fault video to technical support before ordering a replacement.

 

Frequently Asked Questions

Can I hot-swap the MKD090B-047-GP0-KN?
No. Disable the servo drive, remove mains and 24 V DC control power, and allow the DC bus to discharge before disconnecting power or resolver cables. This motor has no holding brake, so secure any movable load first.

Does this motor include a holding brake?
No. The GP0 suffix means no holding brake is installed. Do not use it as a direct replacement for a GP1 motor on a vertical axis unless an external mechanical brake is already fitted.

Is the resolver absolute or incremental?
The KN configuration uses resolver feedback for relative position and commutation. It does not include the integrated multiturn absolute encoder used in KG1 versions.

Can I replace it with an MKD090B-047-GP1-KN?
Not without reviewing the application. The GP1 version adds an 11 Nm holding brake and requires brake-supply wiring, drive configuration, and mechanical clearance checks. The 090B frame and 047 winding match, but the complete type code must be verified.

Which Rexroth drives work with this motor?
MKD motors are used with Rexroth Indramat DDS, DKS, DKC, HDS, and HDD servo drive families. Confirm that the installed drive supports the 047 winding and resolver feedback before ordering.

Why is the rated torque lower than the standstill torque?
The 9.9 Nm rated torque applies at 3,500 rpm, where thermal and back-EMF limits reduce available continuous torque. The 12.0 Nm value is the continuous standstill torque at a 60 K winding temperature rise.

What condition is this motor supplied in?
This is New Original / New Surplus stock, not used or refurbished. Each unit is inspected, function-tested, and shipped in ESD-safe packaging with a test report; photos and test documentation are available on request.