Sale!

Bosch Rexroth MSK030B-0900-NN-M1-UG0-NNNN IndraDyn S Servo Motor

  • Model: MSK030B-0900-NN-M1-UG0-NNNN
  • Brand: Bosch Rexroth (Indramat)
  • Series: IndraDyn S / MSK
  • Core Function: Permanent-magnet synchronous servo motor
  • Product Type: Compact AC Servo Motor
  • Key Specs: Size 030, length B, natural convection, multiturn absolute optical encoder (Hiperface, 128 periods), plain shaft with seal, no holding brake
  • Condition: New Original / New Surplus
Categories: , , , , SKU: MSK030B-0900-NN-M1-UG0-NNNN Brand:

Description

3. Key Technical Specifications

  • Motor size / length: 030 / B
  • Winding code: 0900
  • Cooling: Natural convection (NN)
  • Encoder: Optical multiturn absolute, Hiperface, 128 signal periods (M1)
  • Shaft: Plain shaft with shaft sealing ring (UG0)
  • Holding brake: None
  • Maximum speed: 9000 rpm
  • Maximum torque: 1.8 Nm
  • Continuous current at standstill (100 K): approx. 1.7 A
  • Maximum current: 6.8 A
  • Insulation class: 155
  • Protection: IP65 (with shaft seal) typical for this configuration
  • Connectors: Rotatable (encoder connector typically 240°)
  • Design: Standard (NNNN)
  • Material number (typical): R911308681
  • Note: Exact continuous torque, thermal data, and voltage constant depend on the drive and ambient conditions. Always verify against the motor nameplate and Rexroth project planning data.

4. Product Introduction

The Bosch Rexroth MSK030B-0900-NN-M1-UG0-NNNN is a compact IndraDyn S synchronous servo motor designed for high-speed, low-torque precision applications. It combines a small frame size with natural convection cooling, a multiturn absolute optical encoder, and a sealed plain shaft.

This motor is commonly used in robotics, packaging machines, small positioning axes, and other automated systems where high dynamic response and absolute position feedback are required in a limited space. It pairs with Rexroth IndraDrive controllers for plug-and-play operation.

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Motor does not turn or follows poorly Encoder fault or wrong parameterization ✅ High Check encoder communication and drive diagnostics Verify encoder wiring and motor data set in the drive
Overtemperature fault Overloaded or insufficient cooling ✅ High Monitor motor temperature and ambient conditions Reduce duty cycle or improve airflow; natural convection requires free air circulation
Position error or loss of absolute position Encoder or cable issue ✅ High Check multiturn absolute feedback status Inspect encoder cable and connector; replace motor if encoder fails
Excessive noise or vibration Mechanical misalignment or bearing wear ✅ Medium Check coupling, mounting, and run-out Verify mechanical installation; replace motor if bearings are damaged
Drive reports “motor not identified” Incorrect type code or parameter mismatch ✅ High Compare motor nameplate with drive motor data Load correct MSK030B-0900 parameters
No holding torque when stopped No brake present (by design) ✅ Low Confirm model has no holding brake Use external brake or holding torque from the drive if required

If the issue cannot be isolated, photograph the nameplate (including the full type code and material number) and contact technical support with drive diagnostics.

MSK030B-0900-NN-M1-UG0-NNNN

MSK030B-0900-NN-M1-UG0-NNNN

MSK030B-0900-NN-M1-UG0-NNNN

MSK030B-0900-NN-M1-UG0-NNNN

6. Frequently Asked Questions (FAQ)

Q: What type of motor is the MSK030B-0900-NN-M1-UG0-NNNN?
A: It is a Bosch Rexroth IndraDyn S permanent-magnet synchronous servo motor, size 030, length B.

Q: Does this motor have a holding brake?
A: No. The “NNNN” configuration indicates no holding brake. Holding torque must be provided by the drive or an external brake if required.

Q: What encoder is installed?
A: Optical multiturn absolute encoder with Hiperface interface and 128 signal periods (M1 option).

Q: How is the motor cooled?
A: Natural convection (NN). Ensure adequate free air circulation around the motor.

Q: What is the maximum speed?
A: 9000 rpm.

Q: Is the shaft keyed?
A: No. This version has a plain shaft with shaft sealing ring (UG0).

Q: What condition and warranty do you offer?
A: We supply New Original / New Surplus stock. Units are inspected for basic functionality. Standard coverage is a 1-year warranty against defects. Always provide the complete type code MSK030B-0900-NN-M1-UG0-NNNN (and material number if available) when ordering or requesting support.