Sale!

Bosch Rexroth MSK040C-0600-NN-M1-UG1-NNNN IndraDyn S Servo Motor

  • Model: MSK040C-0600-NN-M1-UG1-NNNN
  • Brand: Bosch Rexroth (Indramat)
  • Series: IndraDyn S / MSK
  • Core Function: Permanent-magnet synchronous servo motor with holding brake
  • Product Type: Compact AC Servo Motor
  • Key Specs: Size 040, length C, natural convection, multiturn absolute optical encoder (Hiperface, 128 periods), plain shaft with seal, 4 Nm electrically released holding brake
  • Condition: New Original / New Surplus

Description

3. Key Technical Specifications

  • Motor size / length: 040 / C
  • Winding code: 0600
  • Cooling: Natural convection (NN)
  • Encoder: Optical multiturn absolute, Hiperface interface, 128 signal periods (M1)
  • Shaft: Plain shaft with shaft sealing ring
  • Holding brake: Electrically released, 4 Nm (UG1)
  • Maximum speed: 7500 rpm
  • Maximum torque: 8.1 Nm
  • Continuous torque at standstill (60 K): approx. 2.7 Nm
  • Continuous current at standstill (60 K): approx. 3.1 A
  • Continuous torque at 100 K: approx. 3.1 Nm
  • Peak current: 12.4 A
  • Rotor inertia: approx. 0.00014 kg·m² (without brake)
  • Weight: approx. 3.9 kg (with brake)
  • Protection: IP65 typical (with shaft seal)
  • Connectors: Rotatable (power and encoder)
  • Design: Standard (NNNN)
  • Typical material number: R911306061
  • Note: Exact continuous ratings depend on ambient temperature, installation, and drive settings. Always verify against the motor nameplate and Rexroth project planning data.

4. Product Introduction

The Bosch Rexroth MSK040C-0600-NN-M1-UG1-NNNN is a compact IndraDyn S synchronous servo motor equipped with a 4 Nm electrically released holding brake. It features natural convection cooling, a multiturn absolute optical encoder with Hiperface interface, and a sealed plain shaft.

This motor is widely used in packaging, assembly, handling, and general automation applications that require precise positioning, absolute feedback, and the ability to hold position when power is removed. It is designed for seamless integration with Rexroth IndraDrive systems.

 MSK040C-0600-NN-M1-UG1-NNNN

MSK040C-0600-NN-M1-UG1-NNNN

 MSK040C-0600-NN-M1-UG1-NNNN

MSK040C-0600-NN-M1-UG1-NNNN

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Motor does not hold position when stopped Brake not engaging or brake circuit fault ✅ High Check brake voltage and diagnostic status Verify brake control wiring and parameters; replace motor if brake fails
Overtemperature fault Overloaded or restricted cooling ✅ High Monitor motor temperature and ambient conditions Ensure free air circulation; reduce duty cycle if necessary
Position error or loss of absolute data Encoder or cable issue ✅ High Check Hiperface communication and multiturn status Inspect encoder cable/connector; replace motor if encoder is faulty
Drive reports brake error Brake feedback or wiring problem ✅ High Review brake diagnostics in the drive Confirm brake is correctly parameterized and wired
Excessive noise or vibration Mechanical misalignment or bearing wear ✅ Medium Check coupling, mounting, and shaft run-out Verify mechanical installation; replace motor if bearings are damaged
Motor not identified by drive Incorrect parameter set ✅ High Compare nameplate type code with drive motor data Load the correct MSK040C-0600 parameters

If the issue cannot be isolated, photograph the nameplate (full type code and material number) and contact technical support with drive diagnostics.

6. Frequently Asked Questions (FAQ)

Q: What type of motor is the MSK040C-0600-NN-M1-UG1-NNNN?
A: It is a Bosch Rexroth IndraDyn S permanent-magnet synchronous servo motor, size 040, length C, with an integrated holding brake.

Q: Does this motor have a holding brake?
A: Yes. It includes a 4 Nm electrically released holding brake (UG1 option).

Q: What encoder is installed?
A: Optical multiturn absolute encoder with Hiperface interface and 128 signal periods (M1).

Q: How is the motor cooled?
A: Natural convection (NN). Adequate free air circulation around the motor is required.

Q: What is the maximum speed and torque?
A: Maximum speed is 7500 rpm; maximum torque is 8.1 Nm.

Q: Is the shaft keyed?
A: No. This version has a plain shaft with shaft sealing ring.

Q: What condition and warranty do you offer?
A: We supply New Original / New Surplus stock. Units are inspected for basic functionality. Standard coverage is a 1-year warranty against defects. Always provide the complete type code MSK040C-0600-NN-M1-UG1-NNNN (and material number if available) when ordering or requesting support.