Description
3. Key Technical Specifications
- Motor size / length: 101 / D
- Winding code: 0200
- Cooling: Natural convection (NN)
- Encoder: Optical multiturn absolute, Hiperface interface, 128 signal periods (M1)
- Shaft: Plain shaft with shaft sealing ring
- Holding brake: None (AG0)
- Power connector: A-side
- Continuous torque at standstill (100 K): 57.0 Nm
- Continuous current at standstill (100 K): 26.8 A
- Maximum torque: 160.0 Nm
- Maximum current: 99.9 A
- Winding inductivity: 6,000 mH
- Maximum speed: approx. 3400 rpm (0200 winding)
- Protection: IP65
- Design: Standard (NNNN)
- Typical material number: R911312450
- Note: Exact continuous ratings depend on ambient temperature, mounting orientation, and drive settings. Always verify against the motor nameplate and Rexroth project planning data.
4. Product Introduction
The Bosch Rexroth MSK101D-0200-NN-M1-AG0-NNNN is a high-torque IndraDyn S synchronous servo motor designed for demanding industrial applications. It features natural convection cooling, a multiturn absolute optical encoder with Hiperface interface, a plain sealed shaft, and an A-side power connector.
This motor is commonly used in machine tools, large packaging systems, material handling, and other automation equipment that require substantial continuous torque and precise absolute position feedback. It integrates directly with Rexroth IndraDrive controllers for high-performance motion control.

MSK101D-0200-NN-M1-AG0-NNNN

MSK101D-0200-NN-M1-AG0-NNNN
5. Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to this Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Overtemperature fault | Overloaded or restricted cooling | ✅ High | Monitor motor temperature and ambient conditions | Ensure free air circulation; reduce duty cycle if necessary |
| Position error or loss of absolute data | Encoder or cable issue | ✅ High | Check Hiperface communication and multiturn status | Inspect encoder cable/connector; replace motor if encoder is faulty |
| Motor does not produce expected torque | Incorrect parameterization or phase fault | ✅ High | Verify motor data set and current measurements | Load correct MSK101D-0200 parameters; check power wiring |
| Excessive noise or vibration | Mechanical misalignment or bearing wear | ✅ Medium | Check coupling, mounting, and shaft run-out | Verify mechanical installation; replace motor if bearings are damaged |
| Drive reports motor not identified | Type code or parameter mismatch | ✅ High | Compare nameplate with drive motor data | Confirm full type code and load matching parameters |
| No holding torque when stopped | No brake present (by design) | ✅ Low | Confirm model has no holding brake | Use external brake or drive holding torque if required |
If the issue cannot be isolated, photograph the nameplate (full type code and material number) and contact technical support with drive diagnostics.
6. Frequently Asked Questions (FAQ)
Q: What type of motor is the MSK101D-0200-NN-M1-AG0-NNNN?
A: It is a Bosch Rexroth IndraDyn S permanent-magnet synchronous servo motor, size 101, length D.
Q: Does this motor have a holding brake?
A: No. The AG0 configuration indicates no holding brake. Holding torque must be provided by the drive or an external brake if required.
Q: What encoder is installed?
A: Optical multiturn absolute encoder with Hiperface interface and 128 signal periods (M1).
Q: How is the motor cooled?
A: Natural convection (NN). Adequate free air circulation around the motor is required.
Q: What are the continuous and maximum torque values?
A: Continuous torque at standstill (100 K) is 57.0 Nm; maximum torque is 160.0 Nm.
Q: Is the shaft keyed?
A: No. This version has a plain shaft with shaft sealing ring.
Q: What condition and warranty do you offer?
A: We supply New Original / New Surplus stock. Units are inspected for basic functionality. Standard coverage is a 1-year warranty against defects. Always provide the complete type code MSK101D-0200-NN-M1-AG0-NNNN (and material number if available) when ordering or requesting support.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626