Description
Core Product Summary
The B&R X20DM9324 is an X20 System digital mixed I/O module with eight 24 VDC digital inputs and four 24 VDC digital outputs. The inputs use sink connections and EN 61131-2 Type 1 characteristics, while the outputs are current-sourcing FET outputs rated 0.5 A per channel and 2 A total.
The module uses 1-wire connections for both inputs and outputs. Its software input filter is configurable from 0 to 25 ms in 0.2 ms increments, and the outputs include thermal shutdown protection for overcurrent or short-circuit conditions, output monitoring, and internal freewheeling diodes for inductive loads. The X20DM9324 requires an X20 bus module and 12-pin X20 terminal block, both ordered separately.
Key Technical Specifications
| Category | Specification |
|---|---|
| Product type | X20 digital mixed I/O module |
| Digital inputs | 8 × 24 VDC, sink, 1-wire connection |
| Input characteristics | EN 61131-2 Type 1 |
| Input voltage | 24 VDC, −15% / +20% |
| Input current at 24 VDC | Typically 3.75 mA |
| Input resistance | Typically 6.4 kΩ |
| Switching thresholds | Low < 5 VDC; high > 15 VDC |
| Hardware input filter | 100 µs or less |
| Software input filter | Default 1 ms; configurable 0 to 25 ms in 0.2 ms increments |
| Digital outputs | 4 × 24 VDC, source, 1-wire connection |
| Output type | Current-sourcing FET |
| Output switching voltage | 24 VDC, −15% / +20% |
| Nominal output current | 0.5 A per output |
| Total nominal output current | 2 A |
| Switching delay | Less than 300 µs for 0 → 1 and 1 → 0 transitions |
| Switching frequency, resistive load | Maximum 500 Hz |
| Output protection | Thermal shutdown for overcurrent or short circuit; internal freewheeling diode |
| Output monitoring | Output monitoring with 10 ms delay |
| Peak short-circuit current | Less than 12 A |
| Off-state leakage current | 5 µA |
| Output on-resistance | 210 mΩ |
| Braking voltage, inductive load | Typically 50 VDC |
| Power consumption | 0.21 W bus; 0.5 W internal I/O |
| Electrical isolation | 500 V AC effective between channel and bus |
| Status indication | I/O function per channel, operating state, and module status |
| Diagnostics | Module run/error and output error status via LED and software |
| Module pitch | 12.5 + 0.2 mm |
| Degree of protection | IP20 |
| Approvals | CE, UKCA, ATEX Zone 2, cULus, cCSAus HazLoc, DNV, CCS, LR, KR, EAC, KC |
Engineering Selection Highlights
- The X20DM9324 combines eight digital inputs and four digital outputs in one X20 module, reducing the number of separate input and output modules needed for a mixed I/O point count.
- Its 24 VDC sink inputs suit field devices that switch the input to the positive supply, while the four source outputs supply 24 VDC loads.
- Each output is rated 0.5 A and the module total is 2 A, so actuator current must be planned within both limits.
- The configurable 0 to 25 ms software filter can be used to adapt input response to the application’s noise and speed requirements.
- Integrated thermal shutdown, output monitoring, and freewheeling diodes support protected switching of inductive loads within the documented operating limits.
- The module uses 1-wire connections and requires an X20 bus module plus a 12-pin X20 terminal block, both ordered separately.
- The IP20 housing and horizontal or vertical mounting options should be matched to the cabinet’s temperature and installation conditions.

X20DM9324

X20DM9324
System Compatibility & Integration Requirements
| Item / Dependency | Verified Compatibility or Requirement | Practical Note |
|---|---|---|
| Automation system | B&R X20 System | The module is an X20 I/O module for an X20 I/O station. |
| Bus module | X20BM11 required; X20BM15 or coated X20cBM11 are documented compatible alternatives | The bus module is ordered separately and provides the module’s bus connection. |
| Terminal block | 1 × X20TB12, 12-pin, 24 VDC keyed | Required for field wiring and ordered separately. |
| Digital inputs | 8 × 24 VDC sink inputs | Field devices must provide a signal compatible with a sink input. |
| Digital outputs | 4 × 24 VDC source outputs | Loads are supplied with positive 24 VDC from the module outputs. |
| Output load | 0.5 A nominal per output; 2 A total | Verify actuator current against both per-channel and total limits. |
| Input filtering | Configurable from 0 to 25 ms in 0.2 ms steps | Configure the software filter for the required response and noise behavior. |
| Inductive loads | Internal freewheeling diode provided | Observe the manufacturer’s inductive-load switching guidance. |
| Mounting | Horizontal or vertical | Ambient temperature limits differ by mounting orientation. |
Dimensions, Mounting & Connection Notes
| Item | Verified data |
|---|---|
| Module pitch | 12.5 + 0.2 mm |
| Mounting orientation | Horizontal or vertical |
| Operating temperature, horizontal | −25 to 60°C |
| Operating temperature, vertical | −25 to 50°C |
| Installation altitude | No limitation from 0 to 2,000 m; above 2,000 m, reduce ambient temperature by 0.5°C per 100 m |
| Degree of protection | IP20 |
| Required terminal block | 1 × X20TB12, 12-pin, 24 VDC keyed |
| Required bus module | 1 × X20BM11; X20BM15 or X20cBM11 are documented compatible alternatives |
| Connection type | 1-wire connections for inputs and outputs |
| Electrical isolation | 500 V AC effective between channel and bus |
Detailed Product Overview
The B&R X20DM9324 is a digital mixed module for the X20 System, combining eight digital inputs and four digital outputs in a single 12.5 mm-wide module. The inputs are designed as 24 VDC sink connections with EN 61131-2 Type 1 behavior. At a nominal 24 VDC input, each input draws approximately 3.75 mA and presents approximately 6.4 kΩ input resistance. A low input state is below 5 VDC, while a high input state is above 15 VDC.
The module includes a hardware input filter of 100 µs or less and a configurable software input filter. The software filter defaults to 1 ms and can be set from 0 to 25 ms in 0.2 ms increments. This allows the input response to be adjusted for the application’s required balance between fast signal detection and rejection of short electrical disturbances.
The four outputs are current-sourcing FET outputs for 24 VDC loads. Each output is rated at 0.5 A, with a total module output current of 2 A. Switching delay is below 300 µs in either direction, and the documented maximum switching frequency for resistive loads is 500 Hz. The outputs include thermal shutdown protection in response to overcurrent or short-circuit conditions, output monitoring with a 10 ms delay, and internal freewheeling diodes for inductive loads. The documented peak short-circuit current is below 12 A.
The X20DM9324 uses 1-wire connections for both inputs and outputs. It requires an X20 bus module and an X20TB12 terminal block, both ordered separately. The bus is electrically isolated from the channel circuits by 500 V AC effective insulation.
The module is IP20 rated, has a fanless design, and can be mounted horizontally or vertically. The permitted operating temperature is −25 to 60°C when mounted horizontally and −25 to 50°C when mounted vertically. At elevations above 2,000 m, the allowable ambient temperature is reduced by 0.5°C for every additional 100 m.
The X20DM9324 carries CE and UKCA approvals and is documented with ATEX Zone 2, cULus industrial control equipment, and cCSAus hazardous-location process control equipment approvals. Marine and regional approvals include DNV, CCS, LR, KR, EAC, and KC. Approval applicability should be assessed against the complete X20 installation and applicable system documentation.
Applications & System Role
The X20DM9324 is a mixed digital I/O module within a B&R X20 I/O station. Its eight inputs acquire 24 VDC discrete field signals, while its four source outputs switch 24 VDC loads such as indicators, relays, contactors, solenoids, or other devices within the 0.5 A per-channel and 2 A total current limits.
The configurable input filter makes the module suitable for applications where input signals require a defined debounce or noise-filtering delay. The output protection and monitoring functions provide status feedback for output faults, supporting fault identification in the connected control system.
Typical fit scenarios include machine panels and automation cells that require a combination of sensor inputs and low-voltage DC actuator outputs in the same X20 I/O group. The module’s suitability depends on the field devices matching its 24 VDC sink-input and source-output electrical characteristics.
FAQ
What is the B&R X20DM9324?
The B&R X20DM9324 is an X20 System digital mixed I/O module with eight 24 VDC digital inputs and four 24 VDC digital outputs.
What type of inputs does the X20DM9324 have?
It has eight 24 VDC sink inputs with EN 61131-2 Type 1 characteristics and 1-wire connections.
What type of outputs does the X20DM9324 have?
It has four 24 VDC current-sourcing FET outputs with 1-wire connections.
How much current can each output supply?
Each output is rated for 0.5 A nominal current. The total nominal output current for the module is 2 A.
Can the input filter be configured?
Yes. The software input filter defaults to 1 ms and can be configured from 0 to 25 ms in 0.2 ms increments.
Does the X20DM9324 protect its outputs?
Yes. The outputs include thermal shutdown for overcurrent or short-circuit conditions, output monitoring with a 10 ms delay, and internal freewheeling diodes for inductive loads.
Which accessories are required for installation?
The module requires one X20 bus module, such as the X20BM11, and one 12-pin X20TB12 terminal block; both are ordered separately.
What are the environmental limits?
The module is IP20 rated and operates from −25 to 60°C horizontally or −25 to 50°C vertically. Storage and transport temperatures are −40 to 85°C.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626