Sale!

Control Techniques NTE-207-CONS-0000 2-inch NT Servo Motor

  • Model: NTE-207-CONS-0000 (MFG # 960750-06)
  • Brand: Control Techniques (Nidec / Emerson)
  • Series: NT
  • Core Function: 2-inch frame AC servo motor with incremental encoder
  • Product Type: Servo Motor
  • Key Specs: 7.5 lb-in continuous torque, 5000 RPM, 230 VAC, IP65
  • Condition: New Original / New Surplus
Categories: , , , , SKU: NTE-207-CONS-0000 Brand:

Description

3. Key Technical Specifications

Parameter Value
Frame Size 2 in (50.8 mm)
Continuous Stall Torque 7.5 lb-in (0.85 Nm)
Peak Torque 22.5 lb-in (2.54 Nm)
Rated Power 0.43 kW
Voltage 230 VAC
Rated / Max Speed 5000 RPM
Encoder Type Incremental
Encoder Resolution 14-bit (2048 lines typical)
Connectors MS style
Mounting Flange English
Brake None
Protection Rating IP65
Shaft Seal Yes
Inertia Low (0.000094 lb-in-sec²)
Number of Poles 8
Approvals cURus
Approx. Dimensions (H × W × D) 3.35 × 2.30 × 6.70 in
Net Weight Approx. 2.7–3.0 lb

4. Product Introduction

The Control Techniques NTE-207-CONS-0000 is a 2-inch frame NT-series AC servo motor designed for precision motion control. It delivers 7.5 lb-in continuous stall torque and peaks at 22.5 lb-in, with a maximum speed of 5000 RPM on 230 VAC.

The motor uses an English mounting flange, MS connectors, and an incremental encoder. It is rated IP65 with a shaft seal and is intended for pairing with Control Techniques / Emerson servo drives in packaging, robotics, and general automation applications that require compact size and low inertia.

NTE-207-CONS-0000

NTE-207-CONS-0000

NTE-207-CONS-0000

NTE-207-CONS-0000

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Motor does not enable Drive parameter mismatch or wiring ✅ High Verify motor model and encoder type in drive software Confirm NTE-207-CONS-0000 parameters and MS pinout
Excessive following error Incorrect torque or inertia values ✅ High Compare continuous/peak torque and inertia settings Enter correct 7.5 lb-in / 0.000094 lb-in-sec² values
Over-temperature fault Overload or insufficient cooling ✅ Medium Monitor continuous current vs. 1.7 A stall rating Reduce load or duty cycle; check ambient temperature
Encoder fault / loss of position Cable or connector issue ✅ High Inspect MS feedback connector and cable continuity Replace or reseat feedback cable
Motor runs but no torque Phase wiring error ✅ High Verify U/V/W connections at MS power connector Correct phase sequence per drive manual
Vibration or noise at speed Mechanical misalignment or bearing wear ❌ Low Check coupling alignment and shaft condition Inspect load mechanics before condemning motor

If the motor still fails after these checks, capture the drive fault log, note the exact error codes, photograph the connectors, and contact technical support with the motor serial number and drive firmware version.

6. Frequently Asked Questions (FAQ)

Q: Is the NTE-207-CONS-0000 compatible with modern Emerson or Nidec drives?
Yes, provided the drive supports the NT motor family and the correct motor data (torque, inertia, encoder resolution) is entered. Confirm compatibility with the specific drive model before installation.

Q: Does this motor include a holding brake?
No. The “CONS” configuration is the non-brake version. Brake models use a different suffix (e.g., CBNS or TONS).

Q: What is the difference between NTE and NTM versions?
NTE denotes the English (imperial) mounting flange. NTM is the metric flange version. Electrical performance is identical; only the mechanical interface differs.

Q: Can I hot-swap this motor?
No. Always power down the drive and wait for bus voltage to discharge before disconnecting or connecting the motor power and feedback cables.

Q: What encoder resolution does it use?
The standard configuration is an incremental encoder, typically 2048 lines (14-bit equivalent after quadrature). Exact resolution should be verified against the nameplate or drive configuration.

Q: Why is surplus stock priced lower than current list?
These are new original or new-surplus units that have not been previously installed. They are functionally tested and carry a standard warranty. OEM lead times for specific NT configurations can be extended; ready stock reduces machine downtime.

Q: Is a shaft seal included?
Yes. The NTE-207-CONS-0000 includes a shaft seal and is rated IP65 when properly installed with sealed connectors.