Sale!

DDK NFT-401RM1A-S Industrial Servo Tool

  • Brand: DDK
  • Model: NFT-401RM1A-S
  • Product category: Listed by third-party suppliers as a servo-tool product.
  • Manufacturer identification: Associated in supplier listings with Japanese DDK / Daiichi-Dentsu.
  • Technical documentation: Exact manufacturer specifications have not been independently verified.
  • Replacement guidance: Match the full model number and suffix against the installed unit before ordering.
  • Procurement guidance: Request a nameplate photograph, product drawing, and applicable technical manual from the supplier before approving a replacement.
Categories: , , , , SKU: NFT-401RM1A-S Brand:

Description

Key Technical Specifications

The manufacturer’s AFC1500 product page lists the NFT-401RM1A-S as a straight-type nutrunner. The specifications below are confirmed by that product listing.

Parameter Specification
Manufacturer Daiichi Dentsu / DDK
Model NFT-401RM1A-S
Product type Servo nutrunner / tightening tool
Tool configuration Straight type
Maximum torque 39.2 N·m
Maximum speed 250 rpm
Tool weight 2.1 kg
Listed compatible controller SAN4-24
Product series AFC1500
Production status Listed as end of production by the manufacturer
Power supply details Confirm with the applicable controller and tool documentation
Connector and cable details Confirm against the original tool and manufacturer drawings

Compatibility note: The NFT-401RM1A-S and NFT-401RM1-S share the same listed maximum torque, speed, and weight. Do not assume every mechanical or electrical detail is interchangeable without checking the complete model suffix and the applicable drawings.

 

Product Introduction

The DDK NFT-401RM1A-S is a straight-type servo nutrunner designed for controlled screw-tightening operations in automated assembly equipment. Daiichi Dentsu lists a maximum torque of 39.2 N·m, a maximum speed of 250 rpm, and a tool weight of 2.1 kg, with the SAN4-24 controller specified as compatible. These characteristics make it relevant to assembly stations that require controlled fastening rather than conventional manual torque tools. The manufacturer lists the AFC1500 series as end of production, so replacement planning should include controller compatibility and spare-part availability.

NFT-401RM1A-S

NFT-401RM1A-S

NFT-401RM1A-S

NFT-401RM1A-S

Installation & Configuration Guide

Check the tool and controller

  • Confirm the full NFT-401RM1A-S model number on the nameplate.
  • Verify that the existing controller is the listed SAN4-24 or that the proposed controller is explicitly approved for this tool.
  • Check cable assemblies, connectors, tool accessories, and mechanical mounting requirements against the manufacturer’s drawings.

Prepare the workstation

  • Stop the machine and isolate electrical and pneumatic or other auxiliary energy sources where applicable.
  • Follow the facility’s lockout/tagout procedure before removing the tool.
  • Secure the tool and reaction-support arrangement so that tightening torque cannot cause uncontrolled movement.

Install the tool

  • Mount the nutrunner using the specified mechanical interface.
  • Inspect the output drive, fastener socket, cable routing, and strain relief.
  • Avoid side loading, misalignment, and cable bending beyond the limits stated in the installation documentation.
  • Use only the accessories approved for the exact tool configuration.

Configure tightening parameters

  • Use the approved controller and configuration procedure.
  • Set the target torque, tightening sequence, speed, and acceptance limits according to the fastener specification and process validation.
  • Do not treat the tool’s maximum torque as the recommended production setting; the appropriate operating range depends on the joint, fastener, and assembly process.

Validate operation

  • Perform a controlled trial using the approved commissioning procedure.
  • Verify tightening results with suitable calibrated measurement equipment.
  • Confirm repeatability, fastening traceability, and fault handling before releasing the station to production.
  • Record the final settings and controller/tool pairing for future maintenance.

Maintenance note: Follow Daiichi Dentsu’s technical documentation for calibration, service intervals, repairs, and any required tool-specific accessories. Do not disassemble the torque-sensing or drive assembly without the appropriate service procedure.

 

Frequently Asked Questions

Q1: What is the DDK NFT-401RM1A-S?

It is a straight-type servo nutrunner used for controlled tightening in industrial assembly systems. The manufacturer lists it in the AFC1500 product family.

Q2: What is its maximum torque?

The manufacturer’s listing specifies a maximum torque of 39.2 N·m. This is a maximum rating, not a universal target for every fastening application.

Q3: What is its maximum speed?

The listed maximum speed is 250 rpm.

Q4: Which controller is compatible with this model?

The manufacturer’s product listing identifies SAN4-24 as the applicable controller. Confirm the exact system configuration and required cables before replacing the tool.

Q5: Is NFT-401RM1A-S interchangeable with NFT-401RM1-S?

Both models appear in the manufacturer’s listing with the same maximum torque, maximum speed, and weight. However, those matching ratings alone do not prove full interchangeability. Check mechanical dimensions, connections, and controller requirements before substitution.

Q6: Is the NFT-401RM1A-S still in production?

The manufacturer’s AFC1500 page labels the product series End of Production. Buyers should confirm remaining stock, repair support, and replacement options with the manufacturer or an authorized supplier.

Q7: What should be checked when sourcing a replacement?

Verify the full model number, maximum torque and speed, controller compatibility, tool condition, cable assemblies, mechanical interfaces, and availability of service support. For used or refurbished equipment, request a condition report and functional test results.