Sale!

ELAU iSH0706001700000001000 70 mm Servo Motor

  • Model: iSH070/60017/0/0/00/0/00/10/00
  • Compact Part Number: ISH0706001700000001000
  • Brand: ELAU / Schneider Electric
  • Series: PacDrive M iSH
  • Core Function: Integrated servo motor and drive-axis operation
  • Product Type: Integrated servo motor
  • Key Specs: 70 mm flange; 6,000 RPM; 1.7 Nm standstill torque
  • Feedback: SinCos SKM 36 encoder
  • Connection: Hybrid connector
  • Condition: Verify New Original, New Surplus, or Refurbished status
  • ⚠️ Obsolete Model: Limited stock available
Categories: , , , , SKU: iSH0706001700000001000 Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer ELAU, now part of Schneider Electric
Full Model iSH070/60017/0/0/00/0/00/10/00
Compact Part Number ISH0706001700000001000
Alternate Reference VIA0702D02A0000, supplier-reported
Product Family PacDrive M iSH
Product Type Integrated servo motor and drive electronics
Flange Size 70 mm
Rated Speed 6,000 RPM
Standstill Torque 1.7 Nm
Peak Torque Approximately 7.6 Nm, supplier-reported
Rated Power Approximately 0.72 kW, supplier-reported
Main DC Bus 560 V DC nominal; verify system range
Auxiliary Supply 24 V DC
Feedback Device SinCos SKM 36 encoder
Shaft Smooth shaft
Brake No brake
Cooling Self-cooled
Protection Rating IP65, supplier and marketplace reported
Connector Hybrid connector
Sealing Without sealing option
Coating Standard coating
Mounting Flange-mounted
Drive Compatibility PacDrive M architecture; verify PS-5/DB-5 configuration
Status Legacy / discontinued; condition varies by supplier

The compact part number and slash-format designation identify the same ELAU iSH servo configuration in supplier records. The VIA0702D02A0000 reference is also associated with this configuration, but confirm the actual nameplate before approving a substitute.

 

Product Introduction

The ELAU iSH070/60017/0/0/00/0/00/10/00, also identified as ISH0706001700000001000, is a PacDrive M iSH integrated servo motor for machine-axis motion control. This configuration uses a 70 mm flange, 6,000 RPM rated speed, 1.7 Nm standstill torque, smooth shaft, SinCos SKM 36 feedback, and a hybrid connector.

It is used where an installed PacDrive M axis requires the same motor, feedback, shaft, brake, sealing, and connector configuration. Do not approve a replacement from the iSH070 family alone; the complete type code controls mechanical and electrical compatibility.

iSH0706001700000001000

iSH0706001700000001000

iSH0706001700000001000

iSH0706001700000001000

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to This Part Quick Check Method Recommendation
Motor does not enable Missing 24 V control supply, drive inhibit, safety circuit, or network fault ⚠️ Medium Measure 24 V DC at the specified auxiliary supply terminals and check the drive diagnostic code Verify the PacDrive controller, safety chain, and drive before replacing the motor
Motor does not rotate Incorrect enable sequence, drive fault, open motor circuit, or mechanical jam ⚠️ Medium Check drive status, enable command, phase continuity, and shaft freedom with power isolated Isolate the motor from the machine load and test according to Schneider Electric procedures
Encoder feedback fault Damaged hybrid cable, connector contamination, wrong encoder type, or encoder failure ✅ High Inspect the hybrid connector and cable; review the drive’s feedback diagnostic and continuity readings Replace the motor only after confirming the cable and drive feedback interface
Position error or following error Incorrect motor data, mechanical overload, coupling problem, or feedback mismatch ✅ High Check motor parameters, actual-versus-commanded position, load movement, and coupling alignment Confirm the complete motor code and parameter set before commissioning
Motor overheats Excessive load, blocked ventilation, high duty cycle, phase-current issue, or winding fault ✅ High Measure phase current, inspect the machine load, and compare temperature with the application limit Correct overload or cooling problems before replacing the motor
Motor trips at acceleration Acceleration too aggressive, load inertia too high, DC-bus issue, or incorrect tuning ⚠️ Medium Review drive current, DC-bus voltage, acceleration profile, and overload history Check sizing and tuning; do not assume a motor failure
Brake-related alarm Incorrect parameterization or a brake fitted to a different motor variant ❌ Low Verify the nameplate configuration; this listed variant is reported without a brake Do not apply brake wiring or brake parameters to this no-brake configuration
Mechanical interference after replacement Wrong shaft, flange, sealing, or connector variant ✅ High Compare dimensions, shaft style, mounting pattern, and connector orientation with the removed unit Match the full type code and inspect the actual replacement before installation
Intermittent drive faults Loose hybrid connector, cable flex damage, grounding issue, or encoder noise ⚠️ Medium Inspect cable routing, shield termination, connector locking, and fault timing during motion Repair the cable or grounding path before condemning the motor
Motor insulation fault Moisture, contamination, damaged winding, or cable fault ✅ High Isolate the motor and perform an insulation-resistance test using the manufacturer-approved method Compare readings with OEM limits; do not megger connected drive electronics
Excessive vibration or noise Bearing wear, misalignment, coupling damage, or mechanical resonance ✅ High Run uncoupled only when safe, inspect bearing noise, and check alignment and shaft runout Investigate the mechanical train before ordering an electrical replacement
No response from the drive Network, controller, power-stage, or commissioning problem ❌ Low to medium Check PacDrive network status, drive DC bus, enable chain, and diagnostic history A nonresponsive drive does not prove the iSH motor is defective

Installation warning: This is an integrated servo-axis component with configuration-sensitive feedback and connector details. Verify the 70 mm flange, smooth shaft, no-brake design, SinCos encoder, IP65 requirement, hybrid connector, and PacDrive M compatibility before installation.

If the fault remains unresolved, contact technical support with photos of the motor nameplate, complete type code, connector, shaft, and mounting face, plus the PacDrive diagnostic code, motor parameters, cable part number, and measured supply voltage.

 

Frequently Asked Questions (FAQ)

 

What is the difference between ISH0706001700000001000 and iSH070/60017/0/0/00/0/00/10/00?

They are compact and slash-format representations of the same ELAU iSH configuration. Use the complete slash-format code for purchasing and compatibility checks because each segment identifies a mechanical, feedback, connector, or option detail.

 

Is this an ELAU motor or a Schneider Electric motor?

The product originates from ELAU, which became part of Schneider Electric. Older equipment may carry ELAU branding, while replacement documentation or supplier listings may use Schneider Electric references. The brand relationship does not remove the need to match the complete model code.

 

Is this unit a complete servo drive?

It is an integrated iSH servo-axis unit with motor and drive electronics, not a standalone PacDrive controller or separate cabinet-mounted drive. Confirm the installed system architecture, compatible power components, network interface, and required cables before ordering.

 

Can I replace it with any 70 mm iSH motor?

No. The 70 mm flange identifies only one mechanical dimension. This listed configuration also specifies 6,000 RPM, 1.7 Nm standstill torque, a smooth shaft, no brake, SinCos SKM 36 feedback, hybrid connection, and specific sealing and coating options. A different iSH070 variant can fit mechanically and still fail commissioning.

 

Does this model include a holding brake?

The listed configuration is reported without a brake. Verify the actual nameplate and rear-end construction before installation. Do not connect brake wiring or configure a brake output unless the replacement documentation explicitly confirms a brake-equipped variant.

 

Is the ISH0706001700000001000 obsolete?

Marketplace and supplier records identify this as a discontinued or legacy PacDrive M component. New original stock may exist, but many available units are refurbished, used, or service-exchange parts. Request the exact condition, serial number, photos, test scope, warranty, and return terms in writing before purchase.

 

Why is a refurbished unit cheaper than a factory replacement?

Refurbished units typically come from recovered industrial inventory or repaired service stock rather than current factory production. A lower price is acceptable only when the supplier states the condition clearly and provides a documented test report. Ask whether testing includes encoder feedback, drive enable, motor rotation, insulation, connector inspection, and load or simulated-load operation.