Sale!

Emerson KJ3221X1-EA1 DeltaV Redundant AO Terminal Block

  • Model: KJ3221X1-EA1
  • Brand: Emerson
  • Series: DeltaV™ M-Series / S-Series (Redundant Analog Output Terminal Block)
  • Core Function: Redundant analog output (AO) signal termination
  • Product Type: Redundant AO Terminal Block
  • Key Specs: 30 VDC @ 200 mA; −40 to +70 °C; Class G3 contaminants
  • Condition: New Original / New Surplus — factory packaging varies by lot
  • Availability: In stock — ships in 3–5 working days (typical)
Categories: , , , , SKU: KJ3221X1-EA1 Brand:

Description

Key Technical Specifications

  • Part Number: KJ3221X1-EA1
  • Product Type: Redundant Analog Output (AO) Terminal Block for DeltaV DCS
  • Voltage Rating: 30 VDC
  • Current Rating: 200 mA maximum
  • Signal Type: Analog output, typically 4–20 mA (HART-capable when paired with HART AO cards)
  • Redundancy Support: Yes — dual-channel AO redundancy
  • Ambient Temperature Range: −40 °C to +70 °C
  • Relative Humidity: 5 to 95% non-condensing
  • Airborne Contaminants: ISA-S71.04–1985 Class G3
  • Shock: 10 g half-sine wave for 11 ms
  • Vibration: 1 mm p-p (2–13.2 Hz); 0.7 g (13.2–150 Hz)
  • Mounting: DIN rail
  • Dimensions (typical): ~114 × 38 × 120 mm
  • Weight: ~0.3 kg (net)
  • Certifications: CE, RoHS; ATEX/IECEx when used with certified DeltaV assemblies

 

Product Introduction

The Emerson KJ3221X1-EA1 is a redundant analog output (AO) terminal block for Emerson’s DeltaV™ DCS, used to terminate and distribute 4–20 mA AO signals in redundant I/O configurations. It pairs with redundant AO cards (e.g., KJ3221X1-BA1 Series 2 AO, 8-channel, 4–20 mA, HART) to provide dual-channel signal paths that can operate simultaneously or switch over seamlessly on primary channel failure.

This terminal block is chosen for its 30 VDC @ 200 mA rating, wide temperature range (−40 to +70 °C), and compatibility with DeltaV’s redundancy strategies, making it suitable for critical loops controlling valves, actuators, or VFDs where uptime matters. In the field, it shows up in safety-instrumented and process control applications where a single failed AO channel must not take the loop down.

 

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
No 4–20 mA at field device Field power missing or fused out; wiring error at terminal block ✅ High Measure 24 V field power at terminal block; check continuity from AO card to field device Verify field PSU and fuses; re-terminate per OEM diagram
One AO channel dead, other works Failed AO card channel; loose terminal screw on that channel ❌ Medium (card/channel) Swap field wiring to the other redundant channel temporarily; check DeltaV diagnostics If channel follows wiring, suspect AO card; if not, check terminal block connections
Intermittent signal under vibration Loose terminal screws or poor strain relief ✅ High Visually inspect terminals; gently tug-test wires; check for cracked insulation Re-secure terminals; add cable clamps; verify DIN rail is solid
AO signal noisy or unstable Ground loops; improper shielding; nearby VFD noise ✅ Medium Measure ground potential between panel and field device; check shield termination Terminate shield at one end only; add isolated signal conditioner if needed
Redundancy alarm in DeltaV One AO channel out of tolerance; mismatch between redundant channels ❌ Medium (system) Review DeltaV I/O diagnostics for channel mismatch or failure flags Investigate AO card health and loop calibration; terminal block rarely causes this alone

If you’re stuck, pull a photo of the wiring at the terminal block, a screenshot of the DeltaV I/O diagnostics, and a multimeter reading of field power and loop current, then send those to support.

KJ3221X1-EA1

KJ3221X1-EA1

KJ3221X1-EA1

KJ3221X1-EA1

Frequently Asked Questions (FAQ)

Q: Is the KJ3221X1-EA1 hot-swappable?
A: The terminal block itself is passive; however, Emerson and site procedures typically require de-energizing field power before working on redundant AO assemblies to avoid arcs or transient outputs. Follow your site’s MOC and LOTO rules.

Q: What signal types does this terminal block support?
A: It’s designed for analog output signals, typically 4–20 mA, and is used with HART-capable AO cards when HART communication is required.

Q: Is this new or refurbished?
A: We supply this as New Original / New Surplus unless otherwise noted. Factory packaging may vary by lot; traceability is maintained via OEM labels and packing docs.

Q: What AO cards does this pair with?
A: Commonly paired with KJ3221X1-BA1 (Series 2 AO, 8-channel, 4–20 mA, HART) and similar redundant AO cards in DeltaV M/S-Series architectures.

Q: What’s the lead time?
A: Typical ship time is 3–5 working days from stock. If you need a specific delivery date, tell us up front so we can stage it.

Q: What warranty do you offer?
A: 1-year warranty against DOA and functional defects. We’ll replace or refund if it fails under normal use within that period.

Q: Why is this cheaper than buying direct from Emerson?
A: This is surplus channel stock — genuine OEM hardware, but sourced via secondary distribution. Same part number, often with original factory labels and packaging.