Sale!

Emerson KJ3242X1-BA1 DeltaV FOUNDATION Fieldbus H1 Card

  • Model: KJ3242X1-BA1 (12P2471X052 / D803054X012)
  • Brand: Emerson
  • Series: DeltaV™ M-Series (FOUNDATION Fieldbus H1)
  • Core Function: FOUNDATION Fieldbus H1 segment interface card
  • Product Type: Fieldbus H1 Card
  • Key Specs: 12 VDC @ 300 mA local bus; 9–32 VDC @ 12 mA/Port fieldbus; −40 to +70 °C; D6 key
  • Condition: New Original / New Surplus — factory packaging varies by lot
  • Availability: In stock — ships in 3–5 working days (typical)
Categories: , , , , SKU: KJ3242X1-BA1 Brand:

Description

Key Technical Specifications

  • Part Number: KJ3242X1-BA1 (alternate ordering codes: 12P2471X052, D803054X012)
  • Product Type: FOUNDATION Fieldbus H1 Card for DeltaV M-Series I/O
  • Local Bus Power: 12 VDC at 300 mA
  • Fieldbus Power: 9 to 32 VDC at 12 mA per port
  • Number of Ports: 1 H1 segment port (simplex card)
  • Protocol: FOUNDATION Fieldbus H1 (IEC 61158-2 physical layer)
  • Ambient Temperature Range: −40 °C to +70 °C
  • Storage Temperature Range: −40 °C to +85 °C
  • Relative Humidity: 5 to 95% non-condensing
  • Airborne Contaminants: ISA-S71.04–1985 Class G3 (conformal coating)
  • Shock: 10 g half-sine wave for 11 ms
  • Vibration: 1 mm p-p (2–13.2 Hz); 0.7 g (13.2–150 Hz)
  • Protection Rating: IP20
  • Terminal Block Key Position: D6
  • Hazardous Area Ratings: II 3G Ex nA IIC Gc; FM12ATEX0090U; IECEx FMG 12.0035U; Nemko 02ATEX431U (EEx nL IIC)
  • Removal/Insertion: Cannot be removed/inserted with system power energized in hazardous areas; non-sparking field circuits must be de-energized before removal/insertion
  • Calibration: Not required; no user-serviceable parts

 

Product Introduction

The Emerson KJ3242X1-BA1 is a DeltaV™ M-Series FOUNDATION Fieldbus H1 card that provides a digital H1 segment interface between the DeltaV LocalBus and field devices (transmitters, valves, analyzers) on a FOUNDATION Fieldbus network. It carries process variables, device status, and diagnostics over the H1 segment, enabling faster fault isolation and device-level diagnostics compared to analog-only wiring.

This card is chosen for its protected fieldbus power circuits (9–32 VDC at 12 mA/port), G3 conformal coating for harsh environments, and D6 keying to prevent mis-installation. In the field, it’s typically deployed in VE4017P0-style H1 I/O assemblies (card + simplex terminal block) for process units that rely on FOUNDATION Fieldbus for critical control loops.

KJ3242X1-BA1

KJ3242X1-BA1

KJ3242X1-BA1

KJ3242X1-BA1

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
No H1 devices online Fieldbus segment power missing or out of range (9–32 VDC) ✅ High Measure segment voltage at terminal block with multimeter; check H1 power supply status Verify H1 PSU output and polarity; check fuses and segment terminators
All devices show “Bad” or “Comms Fail” Missing or incorrect segment termination (open circuit reflections) ✅ High Power down segment; measure resistance across A/B at terminal block (expect ~100 Ω if one terminator, ~50 Ω if two) Add/verify 100 Ω end-of-line terminators at both segment ends
Intermittent device dropouts Noise on segment; ground loops; damaged cable ✅ Medium Use fieldbus diagnostic tool (e.g., Tekmar, Pepperl+Fuchs) to view signal quality and noise floor Check cable routing away from VFDs; verify single-point grounding; replace damaged cable
Card not detected by DeltaV controller Slot fault; card inserted with power on; backplane issue ❌ Medium (carrier/backplane) Check DeltaV diagnostics for slot faults; inspect carrier LEDs Always power down before inserting/removing cards; try known-good slot
One or two devices offline, rest OK Device power or wiring issue; spur length too long ❌ Low (field device/wiring) Inspect device connections; measure voltage at device terminals; check spur length (<120 m total) Re-terminate device; shorten spur; verify device address and configuration

If you’re stuck, pull a screenshot of the DeltaV H1 segment diagnostics, a photo of the terminal block wiring, and a fieldbus diagnostic report (signal quality, noise, device list), then send those to support.

 

Frequently Asked Questions (FAQ)

Q: Is the KJ3242X1-BA1 hot-swappable?
A: No. Emerson specifies this card cannot be removed/inserted with system power energized in hazardous areas, and non-sparking field circuits must be de-energized before removal/insertion. Plan a short maintenance window.

Q: What fieldbus protocol does this card support?
A: FOUNDATION Fieldbus H1 (IEC 61158-2 physical layer). It does not support Profibus PA or HART-IP; those require different cards.

Q: Is this new or refurbished?
A: We supply this as New Original / New Surplus unless otherwise noted. Factory packaging and suffix codes (12P2471X052, D803054X012) may vary by lot.

Q: What terminal block does this pair with?
A: Commonly paired with KJ3242X1-EA1 (simplex H1 terminal block) or KJ3242X1-FA1 (redundant H1 terminal block) depending on the assembly (VE4017P0, VE4017P1, etc.).

Q: What’s the lead time?
A: Typical ship time is 3–5 working days from stock. If you need a specific delivery date, tell us up front so we can stage it.

Q: What warranty do you offer?
A: 1-year warranty against DOA and functional defects. We’ll replace or refund if it fails under normal use within that period.

Q: Why is this cheaper than buying direct from Emerson?
A: This is surplus channel stock — genuine OEM hardware, but sourced via secondary distribution. Same part number, often with original factory labels and packaging.