Description
Key Technical Specifications
- Part Number: KJ3242X1-FA1 (alternate ordering code: 12P2575X032)
- Product Type: Redundant H1 Fieldbus Terminal Block for DeltaV DCS
- Input Power Rating: 35 VDC @ 500 mA
- Communication Type: FOUNDATION Fieldbus H1 (IEC 61158-2 physical layer), redundant paths
- Redundancy Support: Dual independent H1 communication paths for high availability
- Ambient Temperature Range: −40 °C to +70 °C
- Storage Temperature Range: −40 °C to +85 °C
- Relative Humidity: 5 to 95% non-condensing
- Airborne Contaminants: ISA-S71.04–1985 Class G3
- Shock: 10 g half-sine wave for 11 ms
- Vibration: 1 mm p-p (2–13.2 Hz); 0.7 g (13.2–150 Hz)
- Protection Rating: IP20
- Terminal Block Key Position: D8 (typical for redundant H1 assemblies)
- Hazardous Area Ratings: II 3G Ex ec IIC Gc; FM19ATEX0173U; IECEx FMG 19.0067U; when used with certified DeltaV H1 cards and assemblies
- Dimensions (typical): ~100 × 120 × 45 mm
- Weight: ~0.25 kg (net)
- Certifications: CE, UL, CSA; ATEX/IECEx when used in certified assemblies
Product Introduction
The Emerson KJ3242X1-FA1 is a redundant H1 Fieldbus terminal block for Emerson’s DeltaV™ DCS, used to terminate and distribute FOUNDATION Fieldbus H1 signals in redundant I/O configurations. It pairs with redundant H1 card assemblies (e.g., dual KJ3242X1-BA1 or KJ3242X1-BA2 H1 cards) to provide two independent H1 segment paths that can operate simultaneously or switch over seamlessly on primary path failure.
This terminal block is chosen for its 35 VDC @ 500 mA rating, wide temperature range (−40 to +70 °C), and compatibility with DeltaV’s redundancy strategies, making it suitable for critical H1 segments controlling valves, transmitters, or analyzers where uptime matters. In the field, it shows up in VE4017P1-style redundant H1 I/O assemblies where a single failed H1 path must not take the segment down.

KJ3242X1-FA1

KJ3242X1-FA1
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to this Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| No H1 devices online on either path | Fieldbus segment power missing or out of range (9–32 VDC) | ✅ High | Measure segment voltage at terminal block with multimeter; check H1 power supply status | Verify H1 PSU output and polarity; check fuses and segment terminators |
| All devices show “Bad” or “Comms Fail” on both paths | Missing or incorrect segment termination (open circuit reflections) | ✅ High | Power down segment; measure resistance across A/B at terminal block (expect ~100 Ω if one terminator, ~50 Ω if two) | Add/verify 100 Ω end-of-line terminators at both segment ends |
| One path works, other path dead | Failed H1 card or wiring error on that path | ❌ Medium (card/wiring) | Swap field wiring to the other redundant path temporarily; check DeltaV diagnostics | If path follows wiring, suspect H1 card; if not, check terminal block connections |
| Intermittent device dropouts on both paths | Noise on segment; ground loops; damaged cable | ✅ Medium | Use fieldbus diagnostic tool (e.g., Tekmar, Pepperl+Fuchs) to view signal quality and noise floor | Check cable routing away from VFDs; verify single-point grounding; replace damaged cable |
| Redundancy alarm in DeltaV | One H1 path out of tolerance; mismatch between redundant paths | ❌ Medium (system) | Review DeltaV I/O diagnostics for path mismatch or failure flags | Investigate H1 card health and segment configuration; terminal block rarely causes this alone |
If you’re stuck, pull a screenshot of the DeltaV H1 segment diagnostics, a photo of the terminal block wiring, and a fieldbus diagnostic report (signal quality, noise, device list), then send those to support.
Frequently Asked Questions (FAQ)
Q: Is the KJ3242X1-FA1 hot-swappable?
A: The terminal block itself is passive; however, Emerson and site procedures typically require de-energizing field power before working on redundant H1 assemblies to avoid arcs or transient outputs. Follow your site’s MOC and LOTO rules.
Q: What fieldbus protocol does this terminal block support?
A: FOUNDATION Fieldbus H1 (IEC 61158-2 physical layer). It does not support Profibus PA or HART-IP; those require different terminal blocks and cards.
Q: Is this new or refurbished?
A: We supply this as New Original / New Surplus unless otherwise noted. Factory packaging may vary by lot; traceability is maintained via OEM labels and packing docs.
Q: What H1 cards does this pair with?
A: Commonly paired with dual KJ3242X1-BA1 or KJ3242X1-BA2 (Series 2) H1 cards in redundant VE4017P1-style assemblies.
Q: What’s the lead time?
A: Typical ship time is 3–5 working days from stock. If you need a specific delivery date, tell us up front so we can stage it.
Q: What warranty do you offer?
A: 1-year warranty against DOA and functional defects. We’ll replace or refund if it fails under normal use within that period.
Q: Why is this cheaper than buying direct from Emerson?
A: This is surplus channel stock — genuine OEM hardware, but sourced via secondary distribution. Same part number, often with original factory labels and packaging.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626