Description
Key Technical Specifications
- Part Number: KJ4001X1-CE1
- Product Type: 16-Pin Mass Terminal Block for DeltaV DCS
- Number of Pins: 16
- Terminal Type: Screw-clamp terminals
- Terminal Pitch: 5.08 mm (standard spacing)
- Supported Signal Types: Analog input/output, discrete input/output (depends on paired I/O card)
- Wiring Configuration: Supports 2-wire, 3-wire, or 4-wire I/O depending on card and application
- Dielectric Strength: >2000 V AC
- Insulation Resistance: >500 MΩ @ 1000 V DC (some sources cite >1000 MΩ @ 500 V DC)
- Flame Retardancy: UL94 V-0
- Ambient Temperature Range: −40 °C to +70 °C
- Storage Temperature Range: −40 °C to +85 °C
- Relative Humidity: 5 to 95% non-condensing
- Dimensions (L × W × H): ~120 × 70–72 × 25–26 mm
- Weight: ~0.09–0.15 kg (net)
- Mounting: DIN rail or panel mount
- Certifications: CE, UL, RoHS
- Common Pairings: VE4003S2B4 (KJ3222X1-BA1 AI, 4–20 mA, HART, Series 2) uses KJ4001X1-CE1
Product Introduction
The Emerson KJ4001X1-CE1 is a 16-pin mass terminal block for Emerson’s DeltaV™ DCS, used to terminate field wiring for analog and discrete I/O cards in M-Series and S-Series architectures. It provides screw-clamp terminals on a 5.08 mm pitch, supporting 2-wire, 3-wire, or 4-wire I/O configurations depending on the paired I/O card (e.g., 4–20 mA analog input, 24 VDC discrete input).
This terminal block is chosen for its UL94 V-0 flame rating, wide temperature range (−40 to +70 °C), and compatibility with common DeltaV I/O assemblies like VE4003S2B4 (KJ3222X1-BA1 AI, 4–20 mA, HART, Series 2). In the field, it shows up in process control panels where dense, reliable termination is needed for multiple I/O channels in a compact footprint.

KJ4001X1-CE1

KJ4001X1-CE1
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to this Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| One or more channels dead | Loose terminal screw; broken wire strand; cold joint | ✅ High | Visually inspect terminals; gently tug-test wires; check for discoloration or arcing marks | Re-terminate affected channels; torque screws to spec; verify continuity to I/O card |
| Intermittent signal under vibration | Loose terminals or poor strain relief | ✅ High | Visually inspect terminals; gently tug-test wires; check for cracked insulation | Re-secure terminals; add cable clamps; verify DIN rail is solid |
| Channel reads full-scale or zero unexpectedly | Wiring error (swapped +/−); open circuit; short to ground | ✅ High | Measure loop resistance and voltage at terminal block with multimeter; compare to expected values | Re-wire per OEM diagram; check for shorts or opens in field cable |
| Noise on analog signal | Ground loops; improper shielding; nearby VFD noise | ✅ Medium | Measure ground potential between panel and field device; check shield termination | Terminate shield at one end only; add isolated signal conditioner if needed |
| Multiple channels fail simultaneously | I/O card failure; backplane issue; fused field power out | ❌ Medium (card/system) | Check I/O card status LEDs; measure field power at terminal block; review DeltaV diagnostics | Investigate I/O card health and field power distribution; terminal block rarely causes multi-channel failure alone |
If you’re stuck, pull a photo of the wiring at the terminal block, a screenshot of the DeltaV I/O diagnostics, and a multimeter reading of loop resistance/voltage, then send those to support.
Frequently Asked Questions (FAQ)
Q: Is the KJ4001X1-CE1 hot-swappable?
A: The terminal block itself is passive; however, Emerson and site procedures typically require de-energizing field power before working on I/O assemblies to avoid arcs or transient outputs. Follow your site’s MOC and LOTO rules.
Q: What signal types does this terminal block support?
A: It supports analog input/output and discrete input/output signals, depending on the paired I/O card (e.g., 4–20 mA AI, 24 VDC DI).
Q: Is this new or refurbished?
A: We supply this as New Original / New Surplus unless otherwise noted. Factory packaging may vary by lot; traceability is maintained via OEM labels and packing docs.
Q: What I/O cards does this pair with?
A: Commonly paired with VE4003S2B4 (KJ3222X1-BA1 AI, 4–20 mA, HART, Series 2) and similar M/S-Series I/O cards that use a 16-pin mass terminal block.
Q: What’s the lead time?
A: Typical ship time is 3–5 working days from stock. If you need a specific delivery date, tell us up front so we can stage it.
Q: What warranty do you offer?
A: 1-year warranty against DOA and functional defects. We’ll replace or refund if it fails under normal use within that period.
Q: Why is this cheaper than buying direct from Emerson?
A: This is surplus channel stock — genuine OEM hardware, but sourced via secondary distribution. Same part number, often with original factory labels and packaging.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626