WhatsApp: +86 16626708626
Email: 
Phone: +86 16626708626Description
Key Technical Specifications
| Parameter | Value |
| Manufacturer | General Electric (GE) |
| Part Number | IC3600LSRB1 |
| Logic Type | Shift Register / Sequencing |
| System Compatibility | Speedtronic Mark I and Mark II Control Systems |
| Circuit Construction | Discrete Resistors, Transistors, and Capacitors |
| Mounting | Slide-in Rack Mount |
| Connector | Gold-Plated Edge Connector |
| Input Logic Levels | Standard Mark I/II Logic Voltages |
| Operating Temperature | -30 to +70°C (-22 to 158°F) |
| Lead Time Status | Available for Immediate Shipping |
Product Introduction & Supply Chain Strategy
The GE IC3600LSRB1 is a foundational shift register board used in legacy Speedtronic Mark I and Mark II turbine control systems. It is engineered to manage sequential logic operations, ensuring that turbine start-up, shut-down, and protection sequences occur in the precise order required by the OEM. Its discrete component design reflects the robust, high-reliability engineering standards of early-generation automation.
From a procurement perspective, the IC3600LSRB1 is a “non-negotiable” spare. Because Mark I/II systems rely on hardware-based logic rather than modern software, a single component failure on a shift register can freeze an entire sequence. Sourcing this as New Surplus is a strategic necessity; used boards from this era often suffer from “dried out” electrolytic capacitors and brittle solder joints that fail under vibration. New Surplus inventory provides the only reliable bridge to maintain these systems until a full control migration is budgeted.
Installation & Configuration Guide
Stage 1: Pre-Installation (Prep & Safety)
Verify the system is in a safe, non-operational state. De-energize the control cabinet. Use a grounded ESD wrist strap, as even discrete components can be sensitive to high-voltage static discharge. Examine the old board for any manually added jumpers or “flying leads” that were common in field-modified Mark I/II systems.
Stage 2: Removal
Grasp the card by the front pull-handle or edges. Pull the board straight out of the rack guide. Use caution to avoid catching the components on adjacent cards. Inspect the backplane connector for dust or oxidation.
Stage 3: Installation (Clone & Seat)
Inspect the new IC3600LSRB1 to ensure it matches the physical layout of the unit being replaced. Slide the board into the designated slot, ensuring it tracks smoothly along the rails. Apply firm, even pressure to seat the edge connector fully into the backplane socket.
Stage 4: Power-On & Testing
Energize the control rack. Observe the sequence status on the operator panel. Manually step through the first few stages of the logic sequence (if permissible) to verify that the shift register is advancing the signals correctly. Ensure no “Logic Hang” alarms are triggered during the initialization phase.
- IC3600LSRB1
- IC3600LSRB1
Firmware/Software Versions & Upgrade Notes
- Hardware-Based Logic: This module does not contain firmware or software in the modern sense. Its logic is “hard-wired” via its discrete component layout.
- Revision Matching: Ensure the “B1” suffix matches your existing documentation. While some IC3600 series boards are interchangeable, the “LSRB” designation specifically refers to its shift-register function.
- Component Aging: For New Surplus boards stored for long periods, a visual inspection of the capacitors is recommended. Although unused, these components are the most likely point of failure in legacy hardware.
Frequently Asked Questions (FAQ)
What does “Shift Register” mean in this context?
In the Mark I/II systems, this board acts as a “memory” for the sequence of events. It “shifts” a logic signal from one stage to the next as specific field conditions (like pressure or speed) are met.
Are these boards tested before shipping?
Yes. Every IC3600LSRB1 undergoes a physical inspection and continuity check to ensure it meets original GE specifications. We verify that there is no shelf-degradation on the solder joints or connectors.
Can I replace this with a more modern GE board?
No. The Mark I/II architecture is unique to its era. There is no direct “plug-and-play” digital replacement; you must use the original IC3600 series hardware to maintain the integrity of the control loop.
Why is it called “New Surplus” if it was made decades ago?
“New Surplus” means the part was manufactured by GE as a spare but was never put into service. It has remained in protective packaging in a controlled environment, making it significantly more reliable than a “used” part pulled from a running machine.
Do you offer a warranty on such an old part?
Absolutely. We provide a 12-month warranty on this board. We stand behind the quality of our surplus inventory and its ability to restore your system to OEM functionality.
