Description
Key Technical Specifications
| Parameter | Specification / Value |
| Model Number | KSY-464 (KSY 464.80 R6 / KSY 464.20) |
| Manufacturer | GEORGII KOBOLD GmbH & Co. KG (Made in Germany) |
| Motor Type | Permanent Magnet Brushless AC Synchronous Servomotor |
| Stall / Rated Torque (M_0 / M_n) | 2.10 Nm |
| Peak Current (I_0) | 7.20 A |
| Nominal Current (I_n) | 2.40 A RMS |
| Nominal / Max Speed (N_n) | Up to 8,000 RPM |
| Voltage Constant (K_e) | 26 mV/RPM |
| Insulation Class | Class F (VDE 0530 standard) |
| Ingress Protection | IP54 / IP65 sealed housing |
| Operating Voltage (U_n) | 210 V |
| Unit Weight | 6.0 kg (13.2 lbs) |
Product Introduction & Supply Chain Strategy
The GEORGII KOBOLD KSY-464 is a high-performance, German-engineered AC synchronous brushless servomotor designed for automated positioning, assembly systems, robotics, and industrial feeder axes. Operating with a 2.10 Nm torque density and speeds reaching up to 8,000 RPM, it delivers low rotor inertia and rapid acceleration under high thermal efficiency.
Because OEM lead times for legacy KSY-series motors can extend to months or face full discontinuation, securing authentic New Surplus inventory is vital for maintenance planning. Installing an old, rewound, or refurbished motor introduces severe risks, such as insulation breakdown, compromised internal resolver sync, and erratic position feedback. Procuring this New Surplus unit guarantees original factory magnetics, pristine bearing assemblies, and complete operational lifespan, shielding your facility from thousands of dollars per hour in unscheduled downtime.

KSY-464

KSY-464
Installation & Configuration Guide
High Voltage & Mechanical Energy Hazard
High-voltage power feeds (210V AC) drive this motor. Perform complete Lock-Out/Tag-Out (LOTO) on the parent servo controller before touch inspection or wiring changes. Always secure suspended loads or vertical axes mechanically before unbolting motor flanges.
1.Pre-Installation & Safety Controls:5 mins.
Enforce LOTO procedures at the main cabinet. Put on a grounded ESD wrist strap before handling encoder/resolver signal connectors. Record current axis positions and mechanical home offsets in the automation controller.
2.Demounting Failed Motor:10 mins.
Disconnect motor power, earth ground, and resolver cabling. Unbolt the flange mounting hardware carefully, making sure not to bind or side-load the motor shaft during removal. Inspect shaft couplings or planetary gear heads for wear.
3.Flange Mounting & Mechanical Coupling:10 mins.
Clean the mounting flange and check keyway tolerances. Slide the new KSY-464 motor into alignment without striking the drive shaft—axial hammer blows will fracture internal feedback disks or damage bearings. Torque flange bolts in a cross pattern to specification.
4.Wiring & Drive Commutation Calibration:15 mins.
Reattach heavy-duty power leads and resolver feedback connectors. Re-energize the logic circuit, check for phase-rotation faults on the drive board, and run an axis homing routine or electronic phase-angle commutation alignment.
Verification: The axis must execute smooth manual jogging (low speed) without excessive motor housing vibration, positioning lag, or overcurrent alarms on the drive amplifier.
Firmware/Software Versions & Upgrade Notes
- Drive Amplifier Mapping: Compatible with standard digital AC servo amplifiers supporting permanent magnet synchronous motor parameter sets (210V winding class, 26 mV/RPM voltage constant).
- Feedback Interface Integration: Motor parameter configuration (current limits, inductance, thermal constants) resides in the host controller or servo amplifier axis profile. The motor itself requires no firmware flashing.
- Commutation Offset Alignment: If replacing a unit on a system using absolute positioning encoders, always run the controller’s electronic zero/phase alignment routine after physical installation to match the new motor’s physical magnetic pole alignment with the feedback device.
Frequently Asked Questions (FAQ)
Is this GEORGII KOBOLD KSY-464 unit genuine new stock or refurbished?
This component is Brand New Surplus. It is not a rebuilt, rewound, or second-hand motor. It retains factory-original windings, unworn bearings, and pristine internal feedback components to deliver full OEM performance.
What are the operational risks of using a rewound or second-hand motor?
Rewound servo motors often suffer from uneven phase resistance, reduced insulation dielectric strength (Class F rating compromise), and misaligned feedback devices. A winding short during auto-mode operation can destroy the connected servo drive amplifier, turning a minor motor swap into an expensive drive replacement.
Does the KSY-464 motor include an integrated holding brake?
Depending on the exact sub-model extension (e.g., MS-R6 variants), selected units come equipped with an internal 24V holding brake (such as the MS 4 holding brake). Verify your existing part number suffix before ordering to ensure correct brake configuration.
What is the ingress protection (IP) rating of this motor?
The motor housing features IP54 to IP65 sealing, rendering it dust-tight and protected against water splashes standard in industrial automation environments.
What warranty coverage is included with this motor?
Every New Surplus GEORGII KOBOLD KSY-464 comes with a comprehensive 12-Month Replacement Warranty. Prior to dispatch, each motor undergoes rigorous quality control checks, including winding insulation resistance tests, phase balance checks, and physical shaft inspection.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626