Sale!

HILSCHER NT100-RE-DP netTAP 100 Protocol Converter

  • Model: NT100-RE-DP (Part Number: 1712.180)
  • Brand: Hilscher
  • Series: netTAP 100 Series
  • Core Function: Protocol conversion between Real-Time Ethernet protocols and PROFIBUS DP networks.
  • Product Type: Fieldbus to Real-Time Ethernet Gateway
  • Key Specs: 24 V DC input | 2x RJ45 Real-Time Ethernet | 1x DB9 PROFIBUS-DP
  • Condition: New Original / New Surplus (Never refurbished).
  • Inventory Status: Essential communication interface spare; critical for preserving legacy fieldbus connectivity during network migrations.
Categories: , , , , SKU: NT100-RE-DP Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer Hilscher Gesellschaft für Systemautomation mbH
Model / Part Number NT100-RE-DP / 1712.180
Communication Processor netX 100 system-on-chip
Supply Voltage 24 V DC ± 6 V (18–30 V DC range)
Current / Power Consumption 130 mA typical at 24 V DC / 3.2 W
Real-Time Ethernet Protocols PROFINET, EtherCAT, EtherNet/IP, Modbus TCP, POWERLINK, Sercos III
Fieldbus Interface PROFIBUS DP (RS-485, optically isolated DB9 socket)
Ethernet Interface 2x RJ45 ports (100BASE-TX / 10BASE-T switched)
Configuration & Diagnostics SYCON.net via Mini-USB port / SD Card storage (up to 2 GB)
Operating Temperature 0 to +60°C
Mounting & Protection DIN Rail EN 60715 / IP20 enclosure

 

Product Introduction & Supply Chain Strategy

The Hilscher NT100-RE-DP (netTAP 100) is a high-performance protocol converter designed to bridge Real-Time Ethernet networks (PROFINET, EtherNet/IP, EtherCAT, Modbus TCP) with legacy PROFIBUS DP fieldbus segments. Powered by the netX 100 communication controller, it manages I/O data translation with sub-10 ms cycle times, allowing plant engineers to integrate existing PROFIBUS motor drives, valve manifolds, and sensors directly into modern Ethernet control topologies.

Procuring the NT100-RE-DP as New Surplus secures critical communication bridges while managing Total Cost of Ownership (TCO). Sourcing second-hand network gateways introduces severe risks, such as degraded internal flash memory, corrupted bootloaders, or intermittent PHY communication errors caused by continuous thermal stress. Stocking factory-pristine surplus units guarantees reliable data routing, avoiding costly multi-hour network outages while bypassing lengthy OEM distribution wait times.

 

Installation & Configuration Guide

1.Pre-Installation (Prep & Safety):Estimated time: 10 mins.

Disconnect 24 V DC power from the control cabinet terminal blocks. Put on a grounded ESD wrist strap. Use SYCON.net configuration software on your PC to back up the active network topology, device configuration file, and node addresses.

2.Removal:Estimated time: 5 mins.

Unplug the 2-pin COMBICON power connector, RJ45 Ethernet cables, and DB9 PROFIBUS connector. Release the DIN-rail locking latch at the bottom of the enclosure and remove the legacy gateway straight off the mounting rail.

3.Installation (Clone & Seat):Estimated time: 10 mins.

Snap the replacement NT100-RE-DP onto the DIN rail securely. If using SD card configuration transfer, insert the pre-programmed SD card into the memory card slot. Set the rotary address switches to match the node ID of the removed unit, then reattach all network and power connectors.

4.Power-On & Testing:Estimated time: 15 mins.

Apply 24 V DC power to the Mini-COMBICON connector. Monitor the front-panel SYS, APL, LINK, and COM LEDs. Verify that Ethernet LINK LEDs show steady activity and the COM/APL status indicators illuminate solid GREEN, confirming successful cyclic data exchange between the Ethernet master and PROFIBUS slaves.

NT100-RE-DP

NT100-RE-DP

NT100-RE-DP

NT100-RE-DP

Firmware/Software Versions & Upgrade Notes

  • Recommended Version: Load the exact firmware revision matching your required master/slave protocol profile (e.g., PROFINET IO-Device to PROFIBUS DP Master) using Hilscher’s SYCON.net configuration tool.
  • Compatibility Notes: The NT100-RE-DP uses loadable firmware architecture. Ensure the installed firmware license matches your network configuration profile to prevent protocol mismatch errors upon boot.
  • Risk Management: Never disconnect power or interrupt USB communication during a firmware load. Swapping matched hardware using an SD card backup preserves system mapping without requiring a full network re-commissioning cycle.

 

Frequently Asked Questions (FAQ)

Is this Hilscher NT100-RE-DP unit genuinely new or refurbished?

This product is a Brand New Surplus unit. It features original factory packaging, zero wear on terminal points, and has never been installed in a running production facility. We strictly reject second-hand, salvaged, or repaired hardware.

Can this gateway operate as a PROFIBUS Master and EtherNet/IP Adapter simultaneously?

Yes. Depending on the loaded firmware profile, the NT100-RE-DP can act as a PROFIBUS DP Master (controlling up to 125 slaves) while simultaneously functioning as an EtherNet/IP Adapter or PROFINET IO-Device on the primary PLC network.

How do I transfer parameters from a failed unit to the replacement?

If your legacy gateway utilized an SD memory card, simply move the card to the replacement NT100-RE-DP. The device will automatically read the configuration file on bootup. Alternatively, upload the saved .nxd project file via the SYCON.net USB interface.

What is the maximum cyclic data payload supported by this unit?

Payload capacities depend on the configured protocols. For PROFIBUS DP, it supports up to 488 bytes of I/O data in slave mode and up to 11,472 bytes in master mode across connected nodes.

What warranty coverage is included with this product?

Every NT100-RE-DP unit is backed by a comprehensive 1-year replacement warranty, validating our strict inbound functional testing and visual inspection standards.