Description
Key Technical Specifications
| Parameter | Value |
| Valve Function | 3/2-way, Normally Closed (NC) |
| Pilot Technology | Integrated Piezoelectric Pilot Valve |
| Operating Pressure Range | 1.5 to 8.0 bar |
| Nominal Pressure | 6.0 bar |
| Nominal Flow Rate | > 50 L/min |
| Operating Medium | Filtered Compressed Air (ISO 8573-1 compliant) |
| Ambient & Medium Temperature | -25 to +60 °C |
| Protection Class | IP65 (DIN EN 60529) |
| Electrical Characteristics | Self-heating free operation, microcontroller compatible |
| Materials of Construction | Anodized aluminum, brass, spring steel, NBR, ARCAP |
Product Introduction & Supply Chain Strategy
The Hoerbiger P8 385RF-NG-SPT63-B is an advanced piezo-pneumatic 3/2-way switch valve engineered for precise regulation of compressed air and neutral gases in hazardous or sensitive industrial automation environments. By utilizing a low-energy piezoelectric ceramic pilot instead of a conventional magnetic coil, the unit offers virtually zero self-heating, high switching accuracy, and direct compatibility with standard electronic control cards and microcontrollers.
Securing this specialized valve as a certified New Surplus component is vital for maintaining high plant reliability and avoiding protracted downtime in pneumatic control loops. Because industrial process instrumentation often features strict certification requirements and long factory lead times, maintaining factory-sealed surplus inventory eliminates the hidden failure risks associated with second-hand or repaired alternatives, protecting Total Cost of Ownership (TCO) across continuous-run facilities.

P8 385RF-NG-SPT63-B

P8 385RF-NG-SPT63-B
Installation & Configuration Guide
1.Pre-Installation (Prep & Safety):Prerequisite.
Isolate pneumatic supply lines and bleed downstream pressure completely. Disconnect electrical power inputs to the valve interface module. Ensure proper ESD protection is worn before handling connector pins. Inspect the mounting subplate surface for foreign particles or oil contamination.
Verification: Confirm zero pressure on the supply gauge and check that the electrical interface connector shows no active voltage signals.
2.Removal:Mechanical Extraction.
Unplug the electrical connection plug from the valve housing. Remove the mounting screws securing the valve block to its subplate or manifold interface, lifting the unit straight up to avoid damaging alignment pins or internal O-ring seals.
Verification: Check that the manifold gasket seats and interface ports are clean and free of old seal fragments or debris.
3.Installation (Clone & Seat):Hardware Setup.
Place new, clean sealing O-rings into the designated groove channels on the base interface. Position the Hoerbiger P8 385RF-NG-SPT63-B unit squarely onto the manifold block and tighten mounting screws evenly to recommended torque limits. Reconnect the electrical harness securely.
Verification: Visually inspect the mounting gap to guarantee a flush, uniform seal between the valve body and the base plate.
4.Power-On & Testing:Commissioning.
Restore clean, dry compressed air supply lines and re-energize the electrical control circuit. Command a test actuation cycle from the host control system while monitoring pilot response and verifying downstream pressure delivery.
Verification: Listen for clean switching acoustics and confirm that the valve transitions states accurately without pneumatic leakage at the manifold interface.
Firmware/Software Versions & Upgrade Notes
- Electrical Interface Baseline: Ensure that control output cards providing signals to the piezo driver meet the voltage and impedance requirements specified for the P8 series.
- Compatibility Warnings: Do not substitute standard magnetic solenoid drivers directly onto piezo-driven valve architectures without verifying signal conditioning compatibility, as piezoelectric actuators require distinct driving characteristics.
- Maintenance Best Practice: Always maintain dry, filtered instrument air (maintaining a pressure dew point 10K below ambient temperature) to prevent moisture condensation from affecting internal pneumatic channels and electronic components.
Frequently Asked Questions (FAQ)
- Why is this Hoerbiger valve categorized as New Surplus rather than standard factory direct?
This unit is an authentic, original OEM-manufactured product procured from verified surplus reserves following plant inventory rationalization. It has never been installed, field-tested, or subjected to operational media wear.
- How do I know this unit has not been refurbished or repaired?
We maintain a strict zero-tolerance policy against second-hand, rebuilt, or modified parts. Every valve arrives in its original factory packaging with unblemished electrical contacts, pristine port threads, and immaculate internal seals.
- What are the operational dangers of utilizing refurbished pneumatic valves in critical loops?
Refurbished or used valves often suffer from fatigued internal diaphragms, degraded piezo elements, and micro-contaminants stuck in narrow pilot nozzles. These hidden wear factors lead to sluggish response times, erratic switching, and unexpected process interruptions.
- Does this valve require special electrical handling due to its piezo design?
Yes, the unit relies on energy-efficient piezoelectric actuation technology. Ensure control circuits match the specified low-power signal profile to guarantee optimal switching performance.
- What warranty protection comes with this New Surplus unit?
This product is backed by a comprehensive 1-year replacement warranty, matching standard factory assurance parameters and providing complete operational security.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626