Description
Key Technical Specifications
| Parameter | Specification / Value |
| Model Number | LG1093AC01 |
| Manufacturer | Honeywell / GE Systems |
| Application | Industrial Flame Monitoring / Burner Safeguard Control |
| Operating Voltage | 120 V AC / 240 V AC (±10%, 50/60 Hz) |
| Flame Sensor Compatibility | Optical UV / IR / Flame Rod Sensor Inputs |
| Flame Failure Response Time (FFRT) | \le 1.0 s (Safety shutoff execution) |
| Output Contacts | Heavy-duty Form-C safety relay contacts (10 A @ 120 V AC) |
| Power Consumption | Approx. 15 VA |
| Enclosure / Mounting | Panel-mount sub-base or heavy-duty chassis sub-rack |
| Operating Temperature | −20 °C to +60 °C (−4 °F to +140 °F) |
| Humidity | 85% RH non-condensing |
| Unit Weight | 1.8 kg (3.97 lbs) |
Product Introduction & Supply Chain Strategy
The Honeywell / GE LG1093AC01 is an industrial flame detector relay module designed for burner management systems (BMS), industrial boilers, process heaters, and combustion furnaces. It continuously evaluates high-frequency optical or ionization flame sensor signals, executing immediate safety shutoff commands (\le 1.0 s) to fuel safety shutoff valves upon detecting flame failure, preventing unburned fuel accumulation and explosive hazards.
Because legacy flame safeguard modules are subject to long OEM manufacturing lead times or product line obsolescence, maintaining authentic New Surplus LG1093AC01 modules in stock is an essential plant reliability measure. Replacing a flame relay module with a non-identical or modified system requires extensive safety re-validation, flame response re-tuning, and re-inspection by boiler safety authorities. Utilizing factory-sealed New Surplus units preserves existing panel wiring and safety interlock logic while eliminating the severe risks of second-hand boards—such as degraded relay contacts, drift-prone flame signal amplifier circuits, or heat-fatigued power components. Keeping 1–2 New Surplus units as strategic buffer stock ensures zero measurement or burner outage during continuous thermal process runs.

LG1093AC01

LG1093AC01
Installation & Configuration Guide
Explosion & High Voltage Hazard
Flame safeguard systems control combustible fuel valves and high-voltage ignition circuits. Ensure main fuel supply lines are manually isolated and electrical power feeds undergo complete Lock-Out/Tag-Out (LOTO) before opening or servicing the burner control cabinet.
1.Pre-Installation & Safety Prep:5 mins.
Isolate main fuel valves and execute LOTO on 120/240 V AC power supplies. Wear an ESD-grounded wrist strap before handling internal signal wiring. Document terminal wiring layouts and DIP switch configurations on the outgoing module.
2.Demounting Outgoing Module:10 mins.
Unscrew chassis retaining hardware or release sub-base locking clips. Carefully pull the module straight forward from its wiring sub-base to disengage rear terminal spade connectors without damaging wiring harnesses.
3.Hardware Setup & Module Seating:10 mins.
Verify that all jumper blocks and sensitivity configuration switches on the new LG1093AC01 match the outgoing board configuration. Align the replacement module onto the guide tracks, press firmly into the terminal sub-base, and tighten retaining screws.
4.Power-On & Flame Signal Test:15 mins.
Restore control power. Observe front-panel status LEDs: verify that the power LED glows steady GREEN. Initiate a controlled burner trial-for-ignition cycle and measure the flame signal voltage at the test jacks to verify adequate flame signal strength before placing the burner into automatic modulation.
Verification: The relay must acknowledge flame presence during ignition, display stable flame signal readings on test points, and execute a immediate safe shutdown upon simulated flame loss.
Firmware/Software Versions & Upgrade Notes
- System Compatibility: Compatible with standard Honeywell / GE flame safeguard sub-bases and industrial optical/UV flame sensor arrays.
- Hardware Plug-and-Play: The LG1093AC01 operates as a hardware-level safety relay card and does not require software flashing during replacement.
- Flame Sensor Matching: Ensure the flame sensor type jumper (UV scanner vs. Flame Rod) on the side or rear board is configured correctly for your physical sensor hardware to prevent false “No Flame” alarm trips.
Frequently Asked Questions (FAQ)
Is this Honeywell / GE LG1093AC01 module brand new or refurbished?
This component is Brand New Surplus. It is not a pulled card, second-hand module, or refurbished unit. It features factory-original safety relays, pristine terminal connections, and un-degraded internal amplifier circuitry.
Why should our facility avoid buying refurbished flame safeguard modules?
Refurbished flame safeguard modules carry severe risks, including pitted safety relay contacts, dried-out capacitors in the flame amplifier stage, and altered flame response timing. In a combustion environment, a malfunctioning flame relay can fail to close fuel valves during a flameout, leading to dangerous unburned fuel accumulation inside the furnace box.
What is the Flame Failure Response Time (FFRT) for this module?
The LG1093AC01 features a high-speed Flame Failure Response Time of \le 1.0 s, ensuring rapid closure of safety shutoff valves upon loss of combustion.
Do I need to re-wire the control panel when replacing this module?
No. As long as the replacement unit is an authentic LG1093AC01, it plugs directly into your existing sub-base and connects to your established flame scanner cabling without modification.
What warranty is provided with this New Surplus module?
Every New Surplus Honeywell / GE LG1093AC01 module is backed by a standard 12-Month Replacement Warranty. Prior to shipment, each unit undergoes strict quality verification checks, including power-on self-test cycles, terminal continuity checks, and flame signal input response testing.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626