Sale!

Honeywell M9494F1003 Modutrol IV Actuator

  • Model: Honeywell M9494F1003
  • Brand: Honeywell
  • Series: Modutrol IV, Series 90
  • Core Function: Positions burner fuel valves and combustion-air dampers
  • Product Type: Electric proportional control motor / actuator
  • Key Specs: 24 VAC; 300 lb-in torque; 90° to 160° adjustable stroke; 60 to 170 second travel time
  • Condition: New Original / New Surplus, subject to confirmed stock
Categories: , , , , SKU: M9494F1003 Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer Honeywell
Model M9494F1003
Product family Modutrol IV
Actuator series Series 90
Supply voltage 24 VAC
Torque 300 lb-in
Fail-safe mode Non-spring return (NSR)
Control type Proportional / reversing control motor
Stroke range 90° to 160°
Travel time 60 to 170 seconds
Auxiliary switches 2 auxiliary switches
Feedback resistance 135 ohms
Typical application Industrial and commercial gas or oil burner firing-rate control, fuel valve positioning, and combustion-air damper control
Replacement note Listed as an upgraded replacement for Honeywell M9494D1000; verify shaft height, linkage, wiring, and control-signal compatibility before installation

 

Product Introduction

The Honeywell M9494F1003 is a 24 VAC Modutrol IV Series 90 non-spring-return proportional actuator for industrial and commercial burner systems. It drives firing-rate valves, combustion-air dampers, and similar final-control elements in flame-safeguard applications.

With 300 lb-in torque, adjustable 90° to 160° stroke, 60 to 170 second travel, and two auxiliary switches, it is suited to heavier burner linkage assemblies where a low-torque damper actuator is not appropriate. It is commonly used as the updated replacement path for the discontinued M9494D1000, but confirm mechanical mounting and control-interface compatibility before ordering.

M9494F1003

M9494F1003

M9494F1003

M9494F1003

M9494F1003

M9494F1003

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Actuator does not move No 24 VAC at actuator, blown transformer fuse, or open control circuit ❌ Low Measure 24 VAC at the actuator power terminals with the control calling for movement Restore control power and check transformer, fuse, and wiring before replacing the actuator
Motor hums but shaft does not turn Mechanical binding, seized damper/valve linkage, or overloaded actuator ✅ High Disconnect the actuator from the linkage and command it through its stroke If it travels freely uncoupled, repair or free the damper/valve linkage; do not keep forcing a bound actuator
Actuator reaches only one end of stroke Incorrect stroke adjustment, bad feedback potentiometer, or control-signal issue ✅ Medium Check the 135 ohm feedback resistance and observe shaft position during a commanded stroke Recalibrate stroke; replace the actuator if feedback is unstable or open
Position drifts or hunts Unstable control signal, poor ground, loose linkage, or worn feedback element ✅ Medium Monitor the controller output and actuator feedback while commanding a fixed position Stabilize the control signal and tighten linkage; replace the actuator if drift persists
Actuator moves in the wrong direction Reversed control wiring or incorrect stroke/end-switch configuration ✅ High Compare terminal wiring with the burner wiring diagram and observe direction during a low-fire command Correct wiring or control direction before startup; never reverse-engineer burner safety wiring
Auxiliary switch does not change state Incorrect cam setting, failed switch, or wiring fault ✅ Medium Measure switch continuity while manually commanding the actuator through its stroke Reset the cam; replace the actuator if the auxiliary switch remains faulty
No fail-safe movement on shutdown Expected for this model ✅ High Confirm the model suffix: M9494F1003 is non-spring return This actuator does not spring-return; use a spring-return Modutrol model if the safety design requires automatic shutdown positioning

❗ Burner safety warning: Do not bypass flame-safeguard interlocks, proof-of-closure switches, or purge sequencing to test actuator movement. Use the burner-management system’s designated test mode and qualified combustion personnel.

If the actuator still will not position correctly, send the burner wiring diagram, actuator nameplate photo, controller model, and a short video of the commanded stroke before ordering.

 

Frequently Asked Questions

Is the Honeywell M9494F1003 spring-return?
No. It is a non-spring-return (NSR) Modutrol IV actuator. On loss of power it remains in its last position; it does not drive to a safe shutdown position.

What does it drive?
It is intended for burner firing-rate valves, combustion-air dampers, and comparable final-control elements in commercial and industrial gas or oil burner systems.

Can it replace an M9494D1000?
Often yes—the M9494F1003 is commonly presented as the updated replacement for the discontinued M9494D1000. However, verify shaft height, bracket requirements, wiring, torque, stroke, and control compatibility; an adapter bracket may be needed in some installations.

What is its torque rating?
The M9494F1003 is rated for 300 lb-in of torque.

What supply voltage does it require?
It operates from 24 VAC. Confirm transformer capacity, wiring size, and control-circuit voltage before installation.

Does it include auxiliary switches?
Yes. This configuration includes two auxiliary switches, commonly used for low-fire/high-fire proving, interlocks, or status indication.

Why is it more expensive than a普通 HVAC damper actuator?
It is a high-torque Series 90 Modutrol IV actuator designed for industrial burner firing-rate duty, not a lightweight zone-damper actuator. The 300 lb-in rating, Series 90 control platform, auxiliary switches, and flame-safeguard application explain the cost difference.