Description
Key Technical Specifications
| Parameter | Value |
| Manufacturer | ITT Torque Systems |
| Model Number | MT2130-230AF |
| Input Voltage | 230 V AC |
| Motor Type | Brushless AC Servo |
| Insulation Class | Class F |
| Enclosure Rating | TENV / TEFC (Application Dependent) |
| Feedback Device | Encoder / Resolver compatible |
| Operating Temperature | 0 to +40 °C |
| Mounting Type | Flange Mount |
| Bearing Type | Sealed High-Speed Ball Bearings |
Product Introduction & Supply Chain Strategy
The ITT Torque Systems MT2130-230AF is a high-performance brushless servo motor engineered for precise velocity and position control in automated industrial machinery, robotics, and multi-axis CNC systems. It delivers rapid acceleration profiles and steady torque output under demanding duty cycles, ensuring tight synchronization across high-speed manufacturing lines.
Sourcing this unit as a New Surplus asset optimizes your Total Cost of Ownership (TCO) while neutralizing obsolescence risks. Because ITT has phased out active production of this legacy line, relying on refurbished parts introduces severe failure risks that can trigger catastrophic line stoppages. Securing an authenticated, factory-sealed reserve unit guarantees OEM performance, protects your capital investment, and avoids expensive unplanned downtime.

MT2130-230AF

MT2130-230AF
Installation & Configuration Guide
Stage 1: Pre-Installation (Prep & Safety)
- Execute strict lock-out/tag-out (LOTO) procedures on the main drive amplifier and associated power distribution panels.
- Put on a grounded electrostatic discharge (ESD) wrist strap before handling connectors or feedback cables.
- Photograph the existing motor cable pinout, terminal connections, and mechanical alignment markings to ensure exact replication.
Stage 2: Removal
- Disconnect the power plug and feedback cable connectors carefully, avoiding lateral strain on the housing pins.
- Unbolt the mechanical mounting flange evenly in a crisscross pattern to prevent binding.
- Extract the motor straight back from the mating gearbox or coupling to protect the drive shaft from scoring.
Stage 3: Installation (Clone & Seat)
- Inspect the mechanical coupling and mating shaft for wear, burrs, or contamination before mounting.
- Align the new MT2130-230AF flange with the mounting interface and secure bolts to manufacturer torque specs.
- Reconnect the feedback and power harnesses, ensuring locking rings or retaining screws are fully engaged.
Stage 4: Power-On & Testing
- Verify insulation resistance and ground continuity on the power leads prior to energizing the drive.
- Release LOTO and power up the system control rack at a reduced bus voltage if diagnostic modes permit.
- Monitor drive status LEDs for normal handshaking, check for motor cogging or abnormal acoustic noise, and run a low-speed jog test before resuming full production.
Firmware/Software Versions & Upgrade Notes
- Recommended Version: Match the existing motion controller firmware baseline associated with the legacy MT series drives.
- Compatibility Warnings: Upgrading motion controller firmware without verifying drive loop tuning parameters can cause severe tracking errors or resonance issues. Avoid arbitrary firmware upgrades on legacy hardware loops.
- Replacement Strategy: When replacing this motor, keep the exact feedback resolution settings in the drive parameter table. Altering encoder pulses per revolution without updating the axis configuration file will trigger immediate following error faults.
Frequently Asked Questions (FAQ)
Are these units genuinely new, or are they refurbished?
This unit is a Brand New Surplus item. It is entirely unused, originating from factory-sealed OEM inventory reserves. It has never been installed in a live plant, pulled from a decommissioned asset, or subjected to third-party repairs.
Why is New Surplus priced lower than current direct-from-OEM parts?
New Surplus pricing reflects secondary market acquisition channels for discontinued lines. While it may carry a slight premium over used or refurbished alternatives, it remains significantly below current OEM custom-run prices while delivering 100 percent of original factory reliability.
What are the risks of buying a refurbished alternative instead?
Refurbished servo motors frequently conceal degraded winding insulation, worn bearings, and fatigued feedback devices. Saving capital on a used part often results in premature failure, leading to costly emergency downtime that rapidly eclipses any initial savings.
What is the obsolescence status of this motor?
The MT2130-230AF is an end-of-life (EOL) component no longer in active production by ITT. Maintaining a strategic buffer stock of 1-2 new units on-site is vital to prevent extended lead-time delays during unexpected component failures.
What warranty is provided with this unit?
We back this New Surplus unit with a comprehensive 1-year operational warranty, ensuring complete confidence and risk-free integration into your plant automation architecture.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626