Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | KEBA |
| Model | CP 253/W |
| Model designation | CP253W |
| Platform | KEMRO K2-200 |
| Control system | KeControl C2 |
| Product type | Processor module / industrial computer |
| Supply voltage | 24 V DC |
| Application | Machine control / industrial automation |
| System architecture | Modular K2-200 |
| Approx. weight | 1.58 kg |
| Lifecycle | Discontinued |
| Installation | K2-200 modular control system |
The published component data identifies the CP 253/W as a processor module, rather than an I/O module or standalone general-purpose PC. The same source associates it specifically with KeControl C2 and KEMRO K2-200.
Important specification limitation
Publicly indexed documentation does not provide enough reliable evidence to assign a CPU clock speed, RAM capacity, storage capacity, operating system version, display interfaces, Ethernet configuration, or fieldbus configuration specifically to CP 253/W. Those values should not be copied from other K2-200 processor variants.
This distinction matters because KEBA produced several K2-200 processor variants. For example, available K2-200 documentation for other CPU modules lists different processor and memory configurations, so those specifications should not automatically be attributed to CP 253/W.
Product Introduction
The KEBA CP 253/W is a processor module used in the KEMRO K2-200 / KeControl C2 machine-control platform. It serves as the central computing component within the modular automation architecture rather than as a conventional discrete I/O module.
The unit is a legacy component and is now listed by industrial automation suppliers as discontinued. For replacement work, verify the complete K2-200 configuration, processor revision, application software, and stored machine parameters before installation.

K2-200 CP253W

K2-200 CP253W
Installation & Configuration Guide
Stage 1 — Verify the existing controller
- Record the complete marking from the existing processor.
- Confirm CP 253/W / CP253W on the identification label.
- Identify the KEMRO K2-200 rack and installed modules.
- Record the existing software, firmware, and application revision where accessible.
- Back up machine-specific configuration and application data.
- Apply LOTO procedures before accessing the controller cabinet.
Estimated preparation time: 30–60 minutes.
⚠️ Do not substitute another K2-200 CPU solely because its mechanical dimensions appear similar. Processor variants can differ in hardware resources and software compatibility.
Stage 2 — Remove the existing processor
- Shut down the machine through the normal control procedure.
- Isolate the 24 V DC control supply.
- Verify the absence of hazardous voltage before working inside the cabinet.
- Photograph the processor and all connected interfaces.
- Label connections before removal.
- Release the processor from its mounting position according to the K2-200 hardware configuration.
Estimated removal time: 15–30 minutes.
Stage 3 — Install CP 253/W
- Inspect the replacement processor for physical damage or corrosion.
- Verify the model marking and hardware revision.
- Install the processor in the original K2-200 position.
- Reconnect the original interfaces and power connections.
- Check connector seating and mechanical retention.
- Verify the 24 V DC supply polarity and wiring before energizing.
⚠️ Do not power the processor until the supply voltage and connector arrangement have been checked.
Stage 4 — Power-up and commissioning
- Restore the 24 V DC control supply.
- Observe processor diagnostics during startup.
- Confirm that the K2-200 system recognizes the processor.
- Restore the required application configuration.
- Check communication with connected I/O and machine subsystems.
- Test machine operation first without production load.
- Verify safety circuits and machine interlocks.
- Run a controlled production test.
Estimated commissioning time: 1–3 hours, depending on the machine and software configuration.
A processor replacement should be treated as a system-level maintenance operation, not simply a hardware swap. The application image, machine parameters, connected modules, and software revision can determine whether the replacement starts correctly.
FAQ
What is KEBA CP 253/W?
The CP 253/W is a processor module for the KEBA KEMRO K2-200 / KeControl C2 machine-control platform. It functions as the central processing component of the modular control system.
Is CP 253/W a PLC CPU?
It is best described as a processor module / industrial computer within the K2-200 machine-control system. Industrial component databases categorize it under PLC and machine-control equipment.
What power supply does CP 253/W use?
Available product references specify 24 V DC. Verify the actual cabinet power supply and connector wiring against the machine documentation before installation.
Is CP 253/W discontinued?
Yes. Current industrial automation listings identify the CP 253/W as discontinued by the manufacturer. Replacement units are therefore generally sourced from surplus, unused-stock, refurbished, or repair channels.
Can CP 252/W replace CP 253/W?
Do not assume direct interchangeability. Both belong to the KEMRO K2-200 family, but KEBA used different processor variants. The complete hardware configuration and application requirements should be checked before substitution.
Does replacing CP 253/W require software or parameter backup?
Yes. The safest procedure is to back up the machine application and configuration before removing the original processor. A replacement processor may require restoration of machine-specific software and parameters.
What should I verify before purchasing CP 253/W?
Verify the complete CP 253/W identification label, hardware revision, K2-200 system configuration, existing software version, and connector arrangement. If you send a photo of the CP 253/W nameplate, I can also help identify the exact revision and distinguish it from CP 252/W, CP 253/V, and other K2-200 processor variants.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626