Sale!

Kollmorgen SERVOSTAR 610 10 A Digital Servo Amplifier

The Kollmorgen SERVOSTAR 610 is a digital servo amplifier from the SERVOSTAR 600 family, rated for 10 A RMS continuous output current per phase and 20 A peak current for up to five seconds. It operates from a three-phase 230–480 V AC supply and provides 7 kVA rated installed power for S1 operation.

Categories: , , , , SKU: SERVOSTAR 610 10 A Brand:

Description

Core Product Summary

The Kollmorgen SERVOSTAR 610 is a digital servo amplifier from the SERVOSTAR 600 family, rated for 10 A RMS continuous output current per phase and 20 A peak current for up to five seconds. It operates from a three-phase 230–480 V AC supply and provides 7 kVA rated installed power for S1 operation.

The SERVOSTAR 610 uses resolver feedback as its standard motor feedback interface and includes integrated CANopen communication, RS-232 commissioning, configurable analog and digital I/O, encoder emulation, and support for torque, velocity, position, electronic gearing, pulse-following, and motion-task operation. The standard order code is S61000-NA; the -AS option is ordered as S61001-NA.

 

Key Technical Specifications

Item Specification
Manufacturer / model Kollmorgen SERVOSTAR 610
Product type Digital servo amplifier
System family Kollmorgen SERVOSTAR 600
Continuous output current 10 A RMS per phase, ±3%
Peak output current 20 A RMS per phase, maximum 5 seconds, ±3%
Rated installed power 7 kVA for S1 operation
AC supply, 50 Hz 3 × 230 V AC -10% to 480 V AC +10%
AC supply, 60 Hz 3 × 208 V AC -10% to 480 V AC +10%
DC-link voltage 260 to 675 V DC
Motor feedback Resolver
Feedback connector X2 resolver
Internal power dissipation 90 W
Internal regeneration power 200 W
External regeneration power 1,500 W continuous
Switching frequency 8 kHz
Motor current ripple frequency 16 kHz
Velocity-loop bandwidth Up to 400 Hz
Velocity-loop update rate 250 µs (4 kHz)
Position-loop update rate 250 µs (4 kHz)
Commutation update rate 62.5 µs (16 kHz)
Analog inputs 2 configurable differential inputs, ±10 V, 12-bit and 14-bit resolution
Analog outputs 2 configurable outputs, ±10 V, 10-bit resolution
Digital inputs 4 configurable 24 V PLC-compatible inputs
Digital outputs 2 configurable 24 V open-collector PLC-compatible outputs
Communication RS-232 for PC setup; CANopen
Expansion interface Optional expansion card
Drive status relay BTB/RTO contact, 0.5 A at 24 V
Operating ambient temperature 0 to 45 °C; derated above 45 °C up to 55 °C
Storage temperature -25 to 55 °C
Relative humidity Up to 85%, non-condensing
Protection rating IP20
Dimensions without connectors 70 × 275 × 265 mm (W × H × D)
Depth with connectors 273 mm
Weight 4.0 kg

 

Detailed Product Overview

The Kollmorgen SERVOSTAR 610 is a compact, single-axis digital servo amplifier for brushless servo motors. It closes the torque, velocity, and position control loops and provides sine-wave commutation, space-vector modulation, and DQ current control through its digital power stage.

The SERVOSTAR 610 delivers 10 A RMS continuous current per phase and can supply 20 A peak current for five seconds. It accepts a three-phase supply from 230 V AC to 480 V AC at 50 or 60 Hz and operates with a DC intermediate circuit between 260 and 675 V DC. The drive dissipates 90 W at rated current and supports 200 W of internal regeneration or up to 1,500 W of continuous external regeneration power.

The standard drive uses resolver feedback through the X2 connector. Depending on hardware revision and firmware, it can also support sine encoders with BiSS, EnDat 2.1, or HIPERFACE interfaces through X1. The X5 connector provides an encoder-equivalent output, configurable as an incremental A quad B or SSI output, and supports master-slave or electronic-gearing connections.

The SERVOSTAR 610 includes two configurable ±10 V analog inputs, two ±10 V analog outputs, four 24 V digital inputs, and two 24 V open-collector digital outputs. These signals can be assigned to functions such as enable, stop, homing, operating-mode selection, motion-task selection, position capture, and status reporting. An optional I/O expansion card adds 14 optically isolated digital inputs and 8 optically isolated digital outputs.

Commissioning is performed through the X6 RS-232 interface using Kollmorgen MOTIONLINK. The drive includes a three-digit LED display, error history, internal variable monitoring, oscilloscope functionality, and storage for up to 180 motion tasks. The integrated CANopen interface supports multi-axis systems and parameterization of multiple SERVOSTAR 600 drives from a PC.

SERVOSTAR 610 10 A

SERVOSTAR 610 10 A

SERVOSTAR 610 10 A

SERVOSTAR 610 10 A

Dimensions, Mounting & Connection Notes

The SERVOSTAR 610 measures 70 mm wide, 275 mm high, and 265 mm deep without connectors. Its depth increases to 273 mm with connectors installed. The drive weighs 4.0 kg and has an IP20 enclosure rating.

The drive must be mounted vertically with sufficient ventilation and clearance for cooling. It is designed for installation in an electrical enclosure, and the manufacturer specifies that installation, commissioning, and maintenance should be performed only by qualified personnel.

The main power connection is at X0, using three-phase 230–480 V AC and protective earth. The 24 V DC control supply connects at X4 and requires 1 A normally, or 3 A when a motor holding brake is controlled. The motor and brake connect at X9, while the resolver connects at X2.

The X3 connector provides analog and digital I/O. The X5 connector provides encoder emulation, master-slave, and electronic-gearing interfaces. The X6 connector provides RS-232 and CANopen communication. Shielded cables should be terminated at the drive’s front-panel shield connection, and motor cables should use the motor connector with shield plate.

The SERVOSTAR 610 includes an internal brake circuit and supports internal regeneration, an external brake resistor at X8, or DC-bus sharing through X7. Before electrical work, isolate the supply and observe the drive’s discharge requirements; hazardous voltage can remain present after power removal.

 

System Compatibility & Integration Requirements

Item / Dependency Verified Compatibility or Requirement Practical Note
Drive family Kollmorgen SERVOSTAR 600 SERVOSTAR 610 is part of the 601–620 standard servo-amplifier series
Motor feedback Resolver through X2 Standard feedback interface for the SERVOSTAR 610
Optional encoder feedback BiSS, EnDat 2.1, HIPERFACE, or sine encoder through X1 Availability depends on hardware revision and firmware
Motor connection X9 motor/brake connector Supports motor power and optional 24 V motor holding-brake control
Supply connection X0 mains input Three-phase 230–480 V AC, 50 or 60 Hz
Control supply X4 24 V DC auxiliary input 1 A without brake; 3 A when controlling a brake
DC-bus sharing X7 DC-circuit connection Connects multiple SERVOSTAR 600 drives for shared DC-bus operation
External regeneration X8 external brake-resistor connection Supports external regenerative braking
Analog command X3 I/O connector Two configurable ±10 V differential analog inputs
Digital command X3 I/O connector Four 24 V PLC-compatible inputs and two open-collector outputs
Encoder emulation X5 connector Configurable as incremental A quad B or SSI output
Master-slave operation X5 or X3, depending on signal level Supports electronic gearing, pulse following, and connection to up to 16 slave amplifiers
PC setup X6 RS-232 interface Supports PC connection and multi-drop communication to multiple SERVOSTAR 600 drives
CANopen X6 CANopen interface Integrated in the standard drive
Expansion card Optional plug-in expansion card Adds 14 digital inputs and 8 digital outputs
Setup software Kollmorgen MOTIONLINK Used for setup, tuning, monitoring, diagnostics, and motion-task configuration
Firmware Version 8.50 or higher for BiSS/EtherCAT support; 9.00 or higher for standard hardware revision 05.30/05.40 use Firmware requirement depends on hardware revision and selected feedback/interface features

 

FAQ

What is the Kollmorgen SERVOSTAR 610?
It is a 10 A digital servo amplifier in the Kollmorgen SERVOSTAR 600 family, used to control brushless servo motors with resolver feedback.

What is the continuous and peak current rating?
The SERVOSTAR 610 is rated for 10 A RMS continuous current per phase and 20 A RMS peak current per phase for up to five seconds.

What supply voltage does it require?
It requires a three-phase supply of 230 V AC -10% to 480 V AC +10% at 50 Hz, or 208 V AC -10% to 480 V AC +10% at 60 Hz.

What is the standard order code?
The standard SERVOSTAR 610 order code is S61000-NA. The version with the -AS option is S61001-NA.

What motor feedback does the SERVOSTAR 610 use?
The standard feedback interface is a resolver connected at X2. Sine encoder options, including BiSS, EnDat 2.1, and HIPERFACE, are available through X1 depending on hardware revision and firmware.

What communication interfaces are built in?
The drive includes RS-232 for PC setup and CANopen communication through the X6 interface.

Can multiple SERVOSTAR 610 drives share a DC bus?
Yes. The X7 DC-circuit connection supports DC-bus sharing so regeneration energy can be distributed among multiple SERVOSTAR 600 drives.

What I/O does the base drive provide?
It provides two ±10 V analog inputs, two ±10 V analog outputs, four 24 V digital inputs, and two 24 V open-collector digital outputs.

 

Documented Performance Data

Metric Value / Range Test / Operating Condition
Continuous output current 10 A RMS per phase, ±3% SERVOSTAR 610
Peak output current 20 A RMS per phase, ±3% Maximum 5 seconds
Rated installed power 7 kVA S1 operation
Internal power dissipation 90 W At rated current
Internal regeneration power 200 W Internal regenerative circuit
External regeneration power 1,500 W continuous External regenerative resistor
Switching frequency 8 kHz SERVOSTAR 600 power stage
Motor current ripple frequency 16 kHz SERVOSTAR 600 power stage
Velocity-loop bandwidth Up to 400 Hz SERVOSTAR 600 servo control
Position-loop update rate 250 µs (4 kHz) SERVOSTAR 600 servo control
Commutation update rate 62.5 µs (16 kHz) SERVOSTAR 600 servo control
Long-term speed regulation 0.01% SERVOSTAR 600 servo control
Motion-task capacity Up to 180 tasks Stored in permanent memory