Sale!

Kollmorgen SERVOSTAR 620-AS S62001 20 A Digital Servo Amplifier

Item Specification
Manufacturer / model Kollmorgen SERVOSTAR 620-AS S62001
Product type Digital servo amplifier
System family Kollmorgen SERVOSTAR 600
Continuous output current 20 A RMS per phase
Peak output current 40 A per phase for 5 seconds
Continuous input power 14 kVA
AC supply 3 × 230 V AC -10% to 480 V AC +10%, 50 Hz; 3 × 208 V AC -10% to 480 V AC +10%, 60 Hz
DC intermediate circuit 290 to 675 V DC
Control supply 24 V DC, 1 A; 3 A with brake
Categories: , , , , SKU: SERVOSTAR 620-AS S62001 Brand:

Description

Core Product Summary

The Kollmorgen SERVOSTAR 620-AS S62001 is a fully digital servo amplifier from the SERVOSTAR 600 family. It is rated for 20 A RMS continuous current per phase, 40 A peak current for five seconds, and 14 kVA continuous input power on a three-phase 230–480 V AC supply.

The -AS configuration integrates the safety relay and master-slave functions. The drive provides resolver feedback, integrated power supply, RS-232 commissioning, CANopen communication, configurable analog and digital I/O, and support for torque, velocity, position, electronic gearing, pulse following, and motion-task operation. It is intended for single-axis or multi-axis servo systems using compatible Kollmorgen servo motors.

 

Key Technical Specifications

Item Specification
Manufacturer / model Kollmorgen SERVOSTAR 620-AS S62001
Product type Digital servo amplifier
System family Kollmorgen SERVOSTAR 600
Continuous output current 20 A RMS per phase
Peak output current 40 A per phase for 5 seconds
Continuous input power 14 kVA
AC supply 3 × 230 V AC -10% to 480 V AC +10%, 50 Hz; 3 × 208 V AC -10% to 480 V AC +10%, 60 Hz
DC intermediate circuit 290 to 675 V DC
Control supply 24 V DC, 1 A; 3 A with brake
Motor feedback Resolver
Feedback connector X2 resolver
Internal power dissipation 200 W
Internal regeneration power 200 W
External regeneration power 1,500 W
Switching frequency 8 kHz
Motor current ripple frequency 16 kHz
Velocity-loop bandwidth Up to 400 Hz
Velocity-loop update rate 250 µs (4 kHz)
Position-loop update rate 250 µs (4 kHz)
Commutation update rate 62.5 µs (16 kHz)
Analog inputs 2 configurable differential inputs, ±10 V, 12-bit and 14-bit resolution
Analog outputs 2 configurable outputs, ±10 V, 10-bit resolution
Digital inputs 4 configurable 24 V PLC-compatible inputs
Digital outputs 2 configurable 24 V open-collector PLC-compatible outputs
Communication RS-232 for PC setup; CANopen
Expansion interface Optional expansion card
Drive status relay BTB/RTO contact, 0.5 A at 24 V
Operating ambient temperature 0 to 45 °C; derated above 45 °C up to 55 °C
Storage temperature -25 to 55 °C
Relative humidity Up to 85%, non-condensing
Protection rating IP20
Height without connectors 275 mm
Width 120 mm
Weight 7.7 kg

 

Detailed Product Overview

The Kollmorgen SERVOSTAR 620-AS S62001 is the highest-current standard model in the SERVOSTAR 601 to 620 servo-amplifier range. It supplies a three-phase motor through a fully digital control architecture, with resolver feedback, sine-wave commutation, space-vector modulation, and DQ current control.

The S62001 is rated for 20 A RMS continuous current and 40 A peak current for five seconds. It accepts a three-phase supply from 230 V AC to 480 V AC at 50 or 60 Hz and operates with a DC intermediate circuit between 290 and 675 V DC. Its integrated power stage dissipates up to 200 W internally, while the drive supports 200 W of internal regeneration and up to 1,500 W of external regeneration power.

The -AS suffix identifies the integrated safety relay and master-slave option. The built-in safety relay switches off the power stage to prevent unintended restart, while allowing the DC bus to remain energized. The drive also supports DC-bus sharing, allowing regeneration energy to be shared among multiple SERVOSTAR 600 amplifiers.

The S62001 provides two configurable ±10 V analog inputs, two ±10 V analog outputs, four 24 V digital inputs, and two 24 V open-collector digital outputs. The I/O can be assigned to functions including enable, stop, homing, motion-task selection, operating-mode switching, position capture, and status reporting. An optional expansion card adds 14 optically isolated digital inputs and 8 optically isolated digital outputs.

For commissioning and diagnostics, the drive provides an RS-232 interface, a three-digit LED display, error history, internal variable monitoring, and PC-based oscilloscope functionality through Kollmorgen MOTIONLINK. The drive stores up to 180 motion tasks and supports linked motion-task sequences, ten homing methods, S-curve acceleration, absolute and relative moves, registration control, and configurable following-error windows.

 SERVOSTAR 620-AS S62001

SERVOSTAR 620-AS S62001

 SERVOSTAR 620-AS S62001

SERVOSTAR 620-AS S62001

Dimensions, Mounting & Connection Notes

The SERVOSTAR 620-AS S62001 has a 120 mm width, 275 mm height without connectors, and weighs 7.7 kg. The drive must be installed vertically with adequate ventilation and clearance for cooling.

The main power connection is at X0, using three-phase 230–480 V AC and protective earth. The 24 V DC control supply connects at X4 and requires 1 A normally, or 3 A when a motor holding brake is controlled. The motor and brake connect at X9, the resolver connects at X2, and the DC-bus link connects at X7.

The drive provides X3 for analog and digital I/O, X5 for encoder-equivalent output or master/slave encoder input, and X6 for RS-232 and CANopen communication. Shielded cables should be connected to the front-panel shield connection, and motor cables should use the motor connector with shield plate.

The drive includes an internal brake circuit and supports either internal regeneration, an external brake resistor at X8, or DC-bus sharing through X7. Before electrical work, isolate the supply and observe the drive’s discharge requirements; the manual specifies that hazardous voltage may remain present after power removal.

 

System Compatibility & Integration Requirements

Item / Dependency Verified Compatibility or Requirement Practical Note
Drive family Kollmorgen SERVOSTAR 600 S62001 belongs to the SERVOSTAR 601–620 digital servo-amplifier series
Motor feedback Resolver X2 resolver input; resolver feedback is the documented SERVOSTAR 600 feedback type
Motor connection X9 motor/brake connector Supports motor power and optional 24 V motor holding-brake control
Supply connection X0 mains input Three-phase 230–480 V AC, 50 or 60 Hz
Control supply X4 24 V DC auxiliary input 1 A nominal; 3 A when controlling a brake
DC-bus sharing X7 DC-circuit connection Allows DC-bus connection between multiple SERVOSTAR 600 drives
External regeneration X8 external brake-resistor connection Supports external regenerative braking
Analog command X3 I/O connector Two configurable ±10 V analog inputs
Digital command X3 I/O connector Four 24 V PLC-compatible inputs and two open-collector outputs
Encoder emulation X5 encoder-equivalent output Configurable as encoder-equivalent ROD or SSI output
PC setup X6 RS-232 interface Supports PC connection and multi-drop communication to multiple SERVOSTAR 600 drives
CANopen X6 CANopen interface Provides CANopen communication
Expansion card Optional plug-in expansion card Adds 14 digital inputs and 8 digital outputs
Setup software Kollmorgen MOTIONLINK Used for setup, tuning, monitoring, diagnostics, and motion-task configuration
Firmware Version 8.50 or higher for BiSS/EtherCAT support; 9.00 or higher for standard hardware revision 05.30/05.40 use Firmware requirement depends on hardware revision and selected feedback/interface features
Multi-axis operation Up to 16 slave amplifiers on master/slave connection Configurable input ratio; supports electronic gearing and pulse following

 

FAQ

What is the Kollmorgen SERVOSTAR 620-AS S62001?
It is a 20 A digital servo amplifier in the Kollmorgen SERVOSTAR 600 family, designed for three-phase servo motor control with resolver feedback.

What is the continuous and peak current rating?
The S62001 is rated for 20 A RMS continuous current per phase and 40 A peak current per phase for five seconds.

What supply voltage does it require?
It requires a three-phase supply of 230 V AC -10% to 480 V AC +10% at 50 Hz, or 208 V AC -10% to 480 V AC +10% at 60 Hz.

What does the -AS suffix mean?
The -AS configuration includes an integrated safety relay and master-slave function.

What motor feedback does the S62001 use?
It uses resolver feedback through the X2 connector.

What communication interfaces are built in?
The drive provides RS-232 for PC setup and CANopen communication through the X6 interface.

Can multiple S62001 drives share a DC bus?
Yes. The X7 DC-circuit connection supports DC-bus sharing so regeneration energy can be distributed among multiple SERVOSTAR 600 drives.

What I/O does the base drive provide?
It provides two ±10 V analog inputs, two ±10 V analog outputs, four 24 V digital inputs, and two 24 V open-collector digital outputs.

 

Documented Performance Data

Metric Value / Range Test / Operating Condition
Continuous output current 20 A RMS per phase SERVOSTAR S620
Peak output current 40 A per phase for 5 seconds SERVOSTAR S620
Continuous input power 14 kVA SERVOSTAR S620
Internal power dissipation 200 W SERVOSTAR S620
Internal regeneration power 200 W SERVOSTAR S620
External regeneration power 1,500 W External regeneration resistor
Switching frequency 8 kHz SERVOSTAR 600 power stage
Motor current ripple frequency 16 kHz SERVOSTAR 600 power stage
Velocity-loop bandwidth Up to 400 Hz SERVOSTAR 600 servo control
Position-loop update rate 250 µs (4 kHz) SERVOSTAR 600 servo control
Commutation update rate 62.5 µs (16 kHz) SERVOSTAR 600 servo control
Long-term speed regulation 0.01% SERVOSTAR 600 servo control
Motion-task capacity Up to 180 tasks Stored in permanent memory