Sale!

KUKA KSD1-16 Robot Servo Drive Controller

  • Model: KSD1-16 (Part Number: 00-122-285 / OEM Part Number: E93DA552I4B531)
  • Brand: KUKA Robotics / Lenze
  • Series: KUKA Servo Drive (KSD) Series / KR C2 Controller Architecture
  • Core Function: Controls field-oriented current and speed regulation for an individual robot axis motor.
  • Product Type: Single-Axis Servo Drive Module
  • Key Specs: 8.0 A rated current | 16.0 A peak acceleration current | 0–770 VDC intermediate circuit voltage
  • Condition: New Original / New Surplus (Never refurbished)
  • Inventory Status: Legacy EOL component; critical buffer stock required for line continuity on KR C2 controller fleets.
Categories: , , , , Brand:

Description

Key Technical Specifications

Parameter Specification / Value
Part Number KSD1-16 (Alternate P/N: 00-122-285, 00-105-350, E93DA552I4B531)
Controller Compatibility KUKA KR C2 / KR C2 Edition 2005 (KR C2 ed05)
Intermediate Circuit Voltage 0 to 770 VDC (Nominal DC bus input: 565–675 VDC)
Rated Output Current 8.0 A RMS
Peak Acceleration Current 16.0 A RMS (max acceleration current limit)
Output Voltage Range 3-phase AC 0 to 480 VAC
Output Frequency 0 to 480 Hz
Communication Interface Internal Interbus drive bus system
Cooling & Enclosure External heatsink convection / IP54 cabinet mounting
Dimensions & Weight 88 mm (W) x 240 mm (H) x 180 mm (D)
Protection Features Short-circuit protection, motor overcurrent, heatsink over-temperature

 

Product Introduction & Supply Chain Strategy

The KUKA KSD1-16 (00-122-285) Single-Axis Servo Drive Module regulates power and motion execution across individual robot axes within KUKA KR C2 controller cabinets. Operating on field-oriented current control with high-speed Interbus communication, the drive translates trajectory commands from the robot controller into high-precision AC power for servo motors. Industrial production lines rely on the KSD1-16 to drive robot arm axes (Axes 1 through 6) across automotive body shops, material handling, and automated palletizing cells.

Securing the KSD1-16 as New Surplus is a vital supply-chain insurance policy for plants maintaining legacy KR C2 controller installations. Because KUKA has transitioned newer robot generations to the KSP/KSC drive architecture, obtaining factory-new drive modules from traditional channels becomes difficult. Buying used or refurbished drives carries severe operational risks: aging power IGBTs, degraded electrolytic capacitors, and thermal stress on drive gates frequently cause premature failure under high peak acceleration. A single axis drive crash halts the entire robot cell, costing upwards of $20,000 per hour in production downtime. Maintaining genuine New Surplus KSD1-16 inventory guarantees immediate plug-and-play replacement with OEM design life.

KSD1-16

KSD1-16

KSD1-16

KSD1-16

Installation & Configuration Guide

Stage 1: Pre-Installation (Prep & Safety)

  1. Enforce Lock-Out/Tag-Out: Disconnect all main power sources to the KR C2 controller cabinet. Wait at least 10 minutes for internal DC link capacitors (KPS-600) to fully discharge below 50 VDC.
  2. Static Protection: Strap on a grounded ESD wrist band before touching or handling internal drive modules.
  3. Inspect the Replacement Unit: Remove the new KSD1-16 from its anti-static bag and verify that backplane pin headers, top Interbus connector blocks, and power terminal screws are clean and undamaged.

Stage 2: Removal

  1. Disconnect Wiring: Mark and disconnect the Interbus communication ribbon cable, resolver/feedback connections, and motor power plug from the front face of the faulty KSD1-16.
  2. Unfasten Mounting Screws: Loosen the top and bottom retaining screws securing the drive chassis to the KR C2 rack frame.
  3. Extract Module: Carefully pull the module forward out of the drive rack, guiding the rear heatsink out of the enclosure channel without contacting adjacent drive modules.

Stage 3: Installation (Clone & Seat)

  1. Align Module: Slide the new KSD1-16 module along the guide rails into the vacant rack position.
  2. Secure Fasteners: Tighten top and bottom mounting screws firmly to guarantee solid earth ground continuity and flush thermal contact with the cabinet mounting rail.
  3. Reconnect Terminal Cables: Reattach the Interbus cable ribbon connectors and power plug assembly, tightening terminal lock screws to recommended torque settings.

Stage 4: Power-On & Testing

  1. Bus Power Check: Restore main 3-phase power to the KR C2 cabinet and confirm the 24 VDC control power rail operates within tolerance.
  2. LED Diagnostics: Verify the KSD status LEDs. A steady green LED indicates active Interbus synchronization and healthy DC bus pre-charge.
  3. Motion Verification: Clear emergency stop circuits on the KCP2 teach pendant. Jog the corresponding axis manually in T1 mode to verify smooth current draw, encoder tracking, and zero axis fault codes.

 

Firmware/Software Versions & Upgrade Notes

  • System Compatibility: The KSD1-16 is designed for KUKA System Software (KSS) versions 4.1 through 5.6 operating on KR C2 and KR C2 ed05 controllers.
  • Plug-and-Play Parameterization: The KSD1-16 does not require onboard firmware flashing during replacement. Drive motor parameters, current loop gains, and encoder offsets are automatically pushed down to the drive via the Interbus master upon controller boot.
  • Mix-and-Match Caution: Ensure you replace like-for-like drive current ratings. Replacing a KSD1-16 (16A peak) with a lower-rated drive (e.g., KSD1-08) or higher-rated drive (e.g., KSD1-32/48) without modifying the cabinet machine data configuration ($TRAFO_DAT / $MACHINE.DAT) will cause driver mismatch faults or trigger overcurrent trips on heavy axis maneuvers.

 

Frequently Asked Questions (FAQ)

Q: Why buy a New Surplus KUKA KSD1-16 instead of a refurbished or repaired module?

A: Refurbished servo drives frequently suffer from thermal fatigue, micro-cracking in PCB solder joints, and dried-out electrolytic capacitors due to years of exposure to cabinet heat. A refurbished drive may pass basic bench tests but fail under full motor acceleration. Our New Surplus units are 100% genuine, unused modules that deliver original OEM reliability and a complete operating lifespan.

Q: How do I confirm that the KSD1-16 unit I receive is genuinely unused?

A: Every unit passes strict inbound quality verification. The KSD1-16 arrives with pristine terminal screws, unblemished backplane bus pins, zero dust build-up inside the heatsink fins, and sealed anti-static protective packaging.

Q: Can I hot-swap the KSD1-16 while the KR C2 controller is powered on?

A: No. Never remove or insert a KSD1-16 drive while the intermediate DC link circuit (up to 770 VDC) is energized. Pulling a drive module under load creates destructive electrical arcing that damages backplane connectors and adjacent drives.

Q: What is the difference between part numbers 00-122-285 and E93DA552I4B531?

A: 00-122-285 is the official KUKA spare part ordering number, whereas E93DA552I4B531 is the OEM manufacturer (Lenze) part number stamped on the drive side label. Both designations refer to the identical 16A KSD1 drive module used in KR C2 cabinets.

Q: What warranty coverage applies to this drive?

A: We provide a comprehensive 1-Year Warranty on all New Surplus KUKA automation stock. If the module exhibits any hardware defect under standard operating conditions within 12 months, we provide an immediate direct replacement or full repair service.