WhatsApp: +86 16626708626
Email: 
Phone: +86 16626708626Description
Key Technical Specifications
- Part Number: 810-046015-010
- Revision: C (confirm this matches your tool’s required revision)
- Internal Designation: VOIP III
- Manufacturer: Lam Research
- Function: Not independently documented — do not assume signal type, voltage rails, or board function from the part number or the “VOIP III” label alone
- Documentation Status: No public datasheet, system manual cross-reference, or reseller technical description located beyond confirming this is a genuine Lam Research board designation
- Source Condition: Sourced as a used/pulled part from decommissioned or serviced Lam Research tools
Product Introduction
The Lam Research 810-046015-010 is a PCB board assembly internally labeled “VOIP III,” pulled from Lam Research semiconductor process equipment. Beyond confirming this is a genuine Lam Research part number at Revision C, there isn’t published documentation on this specific board’s function circulating publicly — which is typical for Lam’s internal board families.
If your tool calls out this exact part number and revision in its spares list, this is a straightforward like-for-like sourcing situation. If you’re trying to identify a failed board by symptom rather than part number, this listing alone won’t get you there — you’ll need your tool’s wiring prints or a call to Lam field service to confirm function before you buy.
810-046015-010
810-046015-010
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to this Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| Tool fault log references this specific part number or slot | Board failure at the referenced location | ✅ High | Cross-reference your tool’s fault code against the parts manual to confirm this board is implicated | Confirm the fault genuinely points to this board before ordering a replacement |
| Board pulled for preventive replacement, no active fault | N/A — proactive spares stocking | N/A | Verify revision compatibility against your tool’s current BOM | Confirm revision match; this isn’t a diagnostic scenario |
| Uncertain whether this board is the cause of an observed fault | Function of this specific board isn’t independently documented | ❌ Unknown | Consult your tool’s wiring prints or Lam field service before purchasing on a guess | Don’t buy this part speculatively without confirming it’s the actual failure point |
| Board installed but fault persists | Wrong board, wrong revision, or fault lies elsewhere in the system | ✅ High | Recheck your original diagnosis against tool documentation | Revisit the diagnosis rather than continuing to swap boards on a guess |
Because this board’s function isn’t independently documented, the most useful troubleshooting step is confirming with your tool’s own service documentation or Lam field service that this exact part number is the correct failure point before ordering — swapping an unconfirmed board on a guess is the costliest mistake here.
Frequently Asked Questions (FAQ)
What does this board actually do?
Honestly, that’s not something I can confirm from public sources — there’s no published datasheet or system manual excerpt describing this specific board’s function. If your tool’s parts manual calls out this exact part number for a specific subsystem, trust that over any generic description you find in a listing.
Is “VOIP III” related to voice-over-IP telephony?
Almost certainly not — that would be an unusual function for a semiconductor tool board. “VOIP III” is most likely an internal Lam Research board family designation with a different meaning specific to their engineering naming conventions. Don’t assume a networking/telephony function based on the acronym alone.
Can I confirm compatibility before I buy?
Match the full part number and revision letter against your tool’s bill of materials or a fault reference from your tool’s diagnostic log. That’s a more reliable compatibility check than trusting any description attached to a for-sale listing.
Is this new or used?
Sourcing for boards like this is almost entirely used/pulled equipment. Ask the seller directly about their test status — “used, working” and “used, untested” are very different risk levels on a part with this little independent documentation.
Can I hot-swap this while the tool is running?
No. Power down the affected subsystem before removing or installing any control board on a semiconductor process tool. This applies regardless of what the board’s specific function turns out to be.
What’s the safest way to use a listing like this?
Treat it as confirmation that the part number and revision are genuine, not as a technical reference for function or compatibility. Cross-check against your own tool documentation, or contact Lam field service, before committing to the purchase — especially since a wrong guess here means paying twice.
