Description
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | Transition Networks, now associated with Lantronix |
| Part Number | JE-CX-TBT-02 |
| Product Family | Just Convert-IT |
| Product Type | Standalone Ethernet media converter |
| Conversion | 10BASE-T twisted pair to 10BASE-2 coaxial Ethernet |
| RJ-45 Interface | 1 × 10BASE-T port |
| BNC Interface | 1 × 10BASE-2 port |
| Data Rate | 10 Mbps |
| Duplex Mode | Half-duplex |
| RJ-45 Cable Distance | Up to 100 m / 328 ft |
| Coax Cable Distance | Up to 185 m / 607 ft |
| Coaxial Cable | 50 Ω RG-58-type coax |
| Coax Segment Length | 0.5 to 185 m, according to the user guide |
| Network Standard | IEEE 802.3 |
| MDI/MDI-X | Selectable |
| Maximum Coax Devices | Up to 24 devices per coax segment |
| Power Input | 5 V DC, 1.0 A external adapter |
| Status LEDs | PWR, BNC/ACT, TP/ACT, COL |
| Dimensions | 71 × 94 × 25 mm / 2.75 × 3.7 × 1.0 in |
| Operating Temperature | 0 to 50 °C |
| Humidity | 5% to 90%, non-condensing |
| Altitude | Up to 10,000 ft |
| Mounting | Standalone desktop or wall-mount; not rack-mountable |
| Included Accessory | BNC T-connector for daisy-chain applications |
| Compliance | FCC Class A, CE, CISPR22/EN55022 Class A |
| Warranty | Lifetime warranty stated in original product literature; verify seller terms |
The JE-CX-TBT-02 specifications are supported by the original product datasheet and user guide, including the 10BASE-T/10BASE-2 conversion, 5 V DC power requirement, cable distances, LED functions, dimensions, and environmental limits.
Product Introduction
The Lantronix JE-CX-TBT-02, originally marketed by Transition Networks, is a standalone Ethernet media converter that connects legacy 10BASE-2 coaxial networks to 10BASE-T twisted-pair Ethernet. It provides one RJ-45 port, one BNC interface, selectable MDI/MDI-X, and 10 Mbps half-duplex operation under IEEE 802.3.
This unit is used to keep legacy BNC-connected Ethernet devices operating with an RJ-45 hub, switch, workstation, or controller. It does not convert 10BASE-T to modern 100 Mbps or Gigabit Ethernet; confirm that the connected network equipment supports 10 Mbps operation and that the coax segment has correct 50 Ω termination.

JE-CX-TBT-02
Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to This Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| No PWR LED | Missing adapter, incorrect polarity, failed power supply, or converter fault | ✅ High | Measure 5 V DC at the converter power input and confirm the adapter rating | Use the specified adapter; do not substitute an unverified supply |
| TP/ACT LED remains OFF | RJ-45 cable, switch port, MDI/MDI-X setting, or remote device fault | ✅ High | Test the cable, verify switch-port link, and toggle MDI/MDI-X with power applied as directed | Confirm the RJ-45 device and cable before replacing the converter |
| BNC/ACT LED remains OFF | Open coax, missing T-connector, incorrect termination, or inactive coax device | ✅ High | Inspect the BNC T-connector, cable, 50 Ω terminators, and adjacent nodes | Restore the complete 10BASE-2 segment before replacing the converter |
| TP/ACT link works but coax devices are unreachable | Coax topology, termination, addressing, or half-duplex collision problem | ⚠️ Medium | Check both ends of the coax segment for 50 Ω termination and verify the device chain | Correct the physical bus; 10BASE-2 is not a star topology |
| COL LED flashes constantly | Excessive collisions, duplicate traffic, bad termination, or network loop | ⚠️ Medium | Observe collision activity, disconnect nodes one at a time, and inspect coax terminators | Isolate the offending node or repair the coax segment |
| Intermittent communication | Loose BNC connection, aging coax, damaged T-connector, or power instability | ✅ High | Flex-test connectors carefully, inspect BNC locking, and monitor the 5 V DC supply | Replace damaged coax hardware and verify supply stability |
| Network works only with one cable orientation | MDI/MDI-X mismatch or incorrect patch cable | ✅ High | Change the MDI/MDI-X selector and test with a known-good cable | Set the selector for the connected workstation, hub, or switch |
| Coax network fails after adding a device | Excessive segment length, missing terminator, bad T-connector, or more than 24 nodes | ⚠️ Medium | Measure total coax length, count nodes, and verify both terminators | Keep the segment within 185 m and 24 connected devices |
| Link drops when the cabinet warms up | Aging power adapter, thermal fault, or marginal converter electronics | ✅ Medium | Monitor adapter output and converter temperature from 0 to 50 °C ambient conditions | Replace the adapter first; then test the converter under continuous traffic |
| Modern switch does not recognize the link | Switch does not support 10 Mbps half-duplex or auto-negotiation behavior | ⚠️ Medium | Test with a known 10BASE-T-capable switch or manual port configuration | Use compatible legacy Ethernet equipment or an approved intermediary |
| Data errors occur under traffic | Coax reflections, incorrect impedance, shielding damage, or collision overload | ⚠️ Medium | Verify 50 Ω RG-58-type coax, terminators, cable length, and error counters | Repair the physical layer before replacing the converter |
| Converter passes no traffic after replacement | Incorrect model, damaged BNC port, wrong adapter, or defective unit | ✅ High | Test each port separately with a known-good cable and working 10BASE-2 node | Request a serial-number-specific test report or return the unit |
Critical warning: 10BASE-2 requires a properly terminated 50 Ω coax bus. Do not connect the BNC port to an arbitrary coax cable, leave a T-connector unterminated, or treat the segment like a modern point-to-point Ethernet link.
For technical support, provide photos of the BNC topology, terminators, T-connectors, RJ-45 switch port, LED status, power-adapter label, cable lengths, and the connected legacy device.
Frequently Asked Questions (FAQ)
What does the JE-CX-TBT-02 do?
It converts legacy 10BASE-2 coaxial Ethernet to 10BASE-T twisted-pair Ethernet. The RJ-45 side can connect to a compatible hub, switch, workstation, or controller, while the BNC side connects to the coaxial bus.
Is this converter compatible with 100 Mbps Fast Ethernet or Gigabit Ethernet?
The converter operates at 10 Mbps half-duplex. Do not assume that a modern switch will negotiate correctly. Use a switch with explicit 10 Mbps support or configure a compatible port manually where the switch permits it.
How far can the cables run?
The 10BASE-T side supports up to 100 m. The 10BASE-2 side supports up to 185 m using suitable 50 Ω RG-58-type coax. The total coax segment must also follow the topology and node-count limits.
How many devices can share one coax segment?
The product literature specifies up to 24 devices on one coax segment per twisted-pair segment. The segment also requires correct 50 Ω termination at both physical ends.
Does the unit include a power supply?
Confirm the sales package before ordering. The converter requires an external 5 V DC, 1.0 A supply, and some listings may sell the converter separately from the adapter. Verify connector polarity and included accessories.
Is the JE-CX-TBT-02 rack-mountable?
No. It is a standalone desktop or wall-mount converter. The original datasheet states that it is not rack-mountable. Use a suitable enclosure or mounting arrangement if installing it inside an industrial control cabinet.
Why is this part cheaper than a current Ethernet switch?
It is a legacy physical-layer converter, not a modern managed switch. Its value is maintaining a specific 10BASE-2 network segment without replacing connected legacy equipment. Confirm condition, included power adapter, BNC T-connector, warranty, and test results before purchase.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626