Sale!

MEDC PBEB4B6B5DSM7R PB Manual Call Point

  • Model: PBEB4B6B5DSM7R
  • Brand: MEDC (Crouse-Hinds / Eaton)
  • Series: PB Manual Call Point Range
  • Core Function: Manual initiation of fire/alarm systems in hazardous areas
  • Product Type: Explosion-Proof Manual Call Point (Pushbutton)
  • Key Specs: ATEX/IECEx certified, GRP body, DC, single changeover, red finish
  • Condition: New Original / New Surplus
Categories: , , , , SKU: PBEB4B6B5DSM7R Brand:

Description

3. Key Technical Specifications

Parameter Value
Manufacturer MEDC (Eaton / Crouse-Hinds)
Model Number PBEB4B6B5DSM7R
Product Type PB Manual Call Point
Certification ATEX / CENELEC Ex de (EB code)
Entries 4B6B – 2 × M20 bottom
Labels 5 – Tag label required
Voltage D – DC
Switches S – Single changeover
Options M – Self-reset (momentary) or related option
Terminals 7 – 7 × 2.5 mm (standard)
Finish R – Red (standard)
Enclosure Corrosion-free GRP
Ingress Protection IP66 / IP67
SIL Rating SIL 2
Typical Ambient –40 °C to +70 °C (model dependent)

4. Product Introduction

The MEDC PBEB4B6B5DSM7R is a GRP (glass-reinforced polyester) manual call point from the PB series, designed for hazardous area fire and alarm systems. It provides a latched or momentary pushbutton interface for operators to initiate an alarm under ATEX/IECEx certified conditions.

This unit is used in oil & gas, chemical, marine, and industrial plants where an explosion-proof, corrosion-resistant call point is required. The specific configuration includes dual M20 bottom entries, DC operation, single changeover contacts, and a red finish with tag label provision.

5. Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Call point does not activate alarm Open circuit or failed switch ✅ High Continuity test across changeover contacts Replace unit if contacts do not change state
No indication after activation Missing or failed LED option ✅ Medium Check if LED option is fitted and powered Verify wiring to LED if fitted; replace if defective
Difficult to operate / stuck button Mechanical damage or debris ✅ High Visual inspection of pushbutton and lift flap Clean or replace unit
Moisture ingress Damaged seal or incorrect gland ✅ High Inspect IP66/67 seals and cable entries Replace if seals compromised
System sees continuous alarm Contact welded or shorted ✅ High Isolate and measure contact resistance Replace call point

Always isolate power and verify hazardous area permits before working on the unit. If the problem persists after basic checks, provide photos of the unit and terminal wiring to technical support.

PBEB4B6B5DSM7R

PBEB4B6B5DSM7R

PBEB4B6B5DSM7R

PBEB4B6B5DSM7R

6. Frequently Asked Questions (FAQ)

Q: What does the full code PBEB4B6B5DSM7R mean?
A: It is a configured MEDC PB series manual call point: EB certification (ATEX Ex de), 4B6B entries (2 × M20 bottom), tag label, DC voltage, single changeover switch, M option (typically self-reset/momentary related), 7 terminals, red finish.

Q: Is this suitable for hazardous areas?
A: Yes. It carries ATEX/IECEx (and other) certifications for use in Zone 1/2 and equivalent hazardous locations when installed correctly.

Q: Is the button latching or momentary?
A: The “M” in the code indicates a self-reset (momentary) option is included. Confirm exact behavior against the specific datasheet revision.

Q: Can I replace this with a different color or switch configuration?
A: Yes, but the full ordering code must match the required certification, entries, voltage, switches, and options. Do not substitute without verifying the complete specification.

Q: Why is new-surplus pricing lower than list?
A: These units often come from project surplus or excess stock. They are unused original MEDC product and carry a 1-year warranty when supplied as new surplus.

Q: Any installation notes?
A: Use appropriate certified cable glands for the M20 entries. Maintain the IP66/IP67 rating. Follow the manufacturer’s torque and wiring diagrams. Tag labels should be fitted as specified.