Description
Key Technical Specifications
| Parameter | Value |
| Transducer Series | MRE Series (Vibro-Meter Pressure Sensors) |
| Measurement Type | Absolute / Gauge pressure monitoring |
| Output Signal | Standard industrial analog current/voltage loop |
| Operating Temperature | -40 to +125^\circC (application dependent) |
| Wetted Materials | Corrosion-resistant stainless steel construction |
| Enclosure Protection | IP67 / NEMA 4X hermetically sealed |
| Electrical Connection | Industrial multi-pin connector or integrated cable harness |
| Vibration Resistance | Designed for high-vibration turbomachinery environments |
| Compliance Standards | CE, ATEX/IECEx hazardous area certifications (variant dependent) |
Product Introduction & Supply Chain Strategy
The Meggitt Vibro-Meter MRE-256SP052FBB5 is an industrial-grade pressure transducer engineered for high-accuracy measurement in aggressive operating environments. It provides continuous, real-time pressure monitoring across critical turbomachinery systems, including gas turbines, industrial compressors, and high-pressure lubrication loops.
Procuring this sensor as a Brand New Surplus asset shields plant operations from unexpected measurement drift, calibration failure, and costly process trips. Sourcing genuine, factory-fresh hardware eliminates the internal diaphragm fatigue, strain-gauge degradation, and thermal stress inherent in used or repaired sensors, guaranteeing predictable Total Cost of Ownership (TCO) and absolute reliability across control and protection loops.
Installation & Configuration Guide
- Stage 1: Pre-Installation (Prep & Safety): Perform complete lock-out/tag-out (LOTO) and pressure-relief procedures on the target process line. Inspect the mounting port threads and sealing O-rings for cleanliness and structural integrity. Equip an ESD grounding strap if handling signal wiring interfaces.
- Stage 2: Removal: Disconnect the electrical connector and cable assembly from the legacy transducer. Unscrew the unit carefully from the process thread, ensuring zero residual pressure exists in the isolation manifold.
- Stage 3: Installation (Clone & Seat): Apply approved thread sealant or verify the condition of the metallic sealing ring/gasket. Thread the MRE-256SP052FBB5 manually into the process port to prevent cross-threading, then torque to manufacturer specifications. Reconnect the wiring harness, ensuring proper shield grounding and strain relief.
- Stage 4: Power-On & Testing: Pressurize the process line gradually while monitoring control system loop power. Verify zero-point calibration, span response, and analog output stability through the distributed control system (DCS) before returning the monitoring loop to active service.

MRE-256SP052FBB5

MRE-256SP052FBB5
Firmware/Software Versions & Upgrade Notes
- Recommended Baseline: Standard analog transducer configuration requiring no embedded firmware flashing; match controller scaling to sensor output range.
- Compatibility Notes: Ensure control system input cards (such as 4–20 mA or high-level voltage input modules) match the electrical output configuration and power loop requirements of the replacement sensor.
- Upgrade Warning: Avoid altering signal scaling parameters in the DCS without verifying actual physical calibration baselines. Always document range modifications during hardware replacements.
Frequently Asked Questions (FAQ)
- Are these pressure sensors truly new or refurbished?
This unit is a Brand New Surplus part, preserved in factory-original packaging, completely unused, and never installed or repaired.
- Why choose New Surplus over a cheaper refurbished unit?
Refurbished pressure transducers frequently suffer from over-ranged sensing diaphragms, fatigued internal strain gauges, and degraded electronic components. Saving nominal capital on a used sensor risks inaccurate readings, false safety trips, or catastrophic pressure boundary leakage.
- What is the strategic inventory plan for this part?
Because pressure transmitters are essential for maintaining safe operating envelopes on rotating equipment, keeping at least 1 spare unit of the MRE-256SP052FBB5 on-site as buffer stock ensures rapid mean-time-to-repair (MTTR) during unexpected failures.
- Is this sensor suitable for hazardous classified environments?
MRE series transducers are typically engineered for heavy-duty industrial applications; verify specific regional hazardous area approvals (ATEX/IECEx) against plant classification requirements prior to installation.
- What warranty terms are included?
Every New Surplus MRE-256SP052FBB5 unit is backed by a comprehensive 1-to-2 year operational warranty, assuring complete dependability for plant instrumentation architectures.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626