Description
Core Product Summary
The MOOG D136-001-007 is an MSC I programmable motion controller within the MOOG M3000 automation-system family. It combines PLC logic, closed-loop motion-control functions, analog and digital I/O, position-feedback interfaces, and industrial communication in a DIN-rail-mounted controller.
The controller provides eight 16-bit analog inputs, two 16-bit analog outputs, eight individually configurable digital I/O points, and two position-transducer interfaces that support incremental encoder or SSI feedback. Communication includes 10BASE-T Ethernet, two independent CAN interfaces, two EIA-232 serial ports, and a PROFIBUS-DP slave interface rated up to 12 Mbit/s. The D136-001-007 is programmed and configured through MOOG Axis Control Software (MACS), which supports IEC 61131 programming.
Key Technical Specifications
| Parameter | Value |
|---|---|
| Manufacturer | MOOG |
| Exact model | D136-001-007 |
| Product type | MSC I Motion Controller |
| System family | MOOG M3000 automation system |
| Digital I/O | 8 points, individually configurable as inputs or outputs |
| Analog inputs | 8 channels, 16-bit resolution |
| Analog input signal ranges | ±10 V, ±10 mA, or 4–20 mA |
| Analog outputs | 2 channels, 16-bit resolution |
| Analog output signal ranges | ±10 V; configurable current-output modes |
| Position-transducer interfaces | 2 |
| Supported feedback types | Incremental encoder or SSI |
| Ethernet | 1 × 10BASE-T, RJ-45 |
| CAN interfaces | 2 independent CAN interfaces |
| PROFIBUS-DP | 1 slave interface, up to 12 Mbit/s |
| Serial communication | 2 × EIA-232 |
| Expansion bus | E-Bus |
| Supply voltage | 24 V DC nominal; 18–36 V DC range |
| Electronics current consumption | 0.5 A at idle; 2 A at full load |
| Mounting | NS 35/7.5 DIN rail |
| Enclosure protection | IP20 |
| Dimensions (W × D × H) | 160 × 170 × 85.5 mm |
| Operating temperature | +5 to +55 °C |
| Storage temperature | -25 to +70 °C |
| Relative humidity | 10–95%, non-condensing |
| Engineering software | MOOG Axis Control Software (MACS), based on CODESYS and supporting IEC 61131 programming |
Engineering Selection Highlights
- The D136-001-007 belongs to the MOOG MSC I controller family and the M3000 automation-system architecture, so it should be selected against the installed MOOG motion-control configuration rather than as a generic PLC.
- Its PROFIBUS-DP slave interface supports communication up to 12 Mbit/s, making the exact ordering number important where the machine uses a PROFIBUS-DP master.
- The two position-transducer interfaces support incremental encoder or SSI feedback, so sensor type, signal format, and wiring must match the configured application.
- Eight 16-bit analog inputs with selectable voltage and current ranges allow the controller to interface with field instrumentation; the configured input mode must match the connected signal.
- Two 16-bit analog outputs provide command signals for compatible control equipment; output mode and electrical requirements should be checked before connection.
- Eight digital I/O points can be individually assigned as inputs or outputs, allowing the channel allocation to follow the machine-control requirement.
- The E-Bus connection supports expansion with compatible MOOG modules, so any installed expansion hardware should be included in the system configuration.

D136-001-007

D136-001-007
System Compatibility & Integration Requirements
| Item / Dependency | Verified Compatibility or Requirement | Practical Note |
|---|---|---|
| Controller family | MOOG MSC I Motion Controller | Match the exact ordering number to the installed controller architecture. |
| Automation system | MOOG M3000 automation system | Confirm the installed system platform before selecting or replacing the controller. |
| PROFIBUS-DP | Slave interface, up to 12 Mbit/s | Confirm master configuration, device addressing, and network settings. |
| Ethernet | 10BASE-T, RJ-45 | Verify network cabling, addressing, and communication configuration. |
| CAN | Two independent CAN interfaces | Confirm bus topology and transmission-rate settings. |
| Serial communication | Two EIA-232 ports | One port supports MACS communication; the other is available for application use. |
| Position feedback | Two interfaces for incremental encoder or SSI | Match sensor type, signal format, and wiring to the configured application. |
| Analog I/O | Eight 16-bit inputs and two 16-bit outputs | Match signal ranges and modes to the connected field devices. |
| Digital I/O | Eight configurable input/output points | Confirm channel allocation and field-circuit loading. |
| Expansion | E-Bus supports up to seven additional modules | Confirm the selected extension modules and system configuration. |
| Engineering software | MOOG Axis Control Software (MACS) | Use the applicable application project and hardware configuration for commissioning. |
Dimensions, Mounting & Connection Notes
| Item | Verified information |
|---|---|
| Dimensions (W × D × H) | 160 × 170 × 85.5 mm |
| Mounting | NS 35/7.5 DIN rail |
| Enclosure protection | IP20 |
| Connection method | Plug-in terminal strips with screw or clamp connections |
| Supply voltage | 24 V DC nominal; 18–36 V DC range |
| Electronics current consumption | 0.5 A at idle; 2 A at full load |
| Operating temperature | +5 to +55 °C |
| Storage temperature | -25 to +70 °C |
| Relative humidity | 10–95%, non-condensing |
Detailed Product Overview
The MOOG D136-001-007 is an MSC I motion controller designed to combine programmable logic control with motion-control functions in the MOOG M3000 automation-system family. It provides the processing, I/O, feedback, and communication functions required for closed-loop control applications involving compatible electric or hydraulic motion axes.
The controller includes eight 16-bit analog inputs and two 16-bit analog outputs. Input channels can be configured for supported voltage or current signals, including ±10 V, ±10 mA, and 4–20 mA. Output channels support ±10 V operation and configurable current-output modes. These interfaces allow the controller to receive process measurements and issue command signals to compatible field equipment, provided the selected signal mode matches the connected device.
Eight digital I/O points can be individually configured as inputs or outputs through the engineering software. The documented maximum current per digital output is 0.5 A. This configurable arrangement allows the controller’s digital channels to be allocated according to the machine’s interlocking, status, and command requirements.
For motion feedback, the D136-001-007 provides two position-transducer interfaces. These interfaces support incremental encoder or SSI configurations. The encoder interface supports frequencies up to 8 MHz, while SSI operation supports 8–32 bit data in Gray or binary format. The selected feedback configuration must correspond to the installed sensor type, signal format, and wiring arrangement.
Communication capability includes 10BASE-T Ethernet through an RJ-45 connector, two independent CAN interfaces, two EIA-232 serial ports, and a PROFIBUS-DP slave interface rated up to 12 Mbit/s. The PROFIBUS-DP interface is a defining feature of the D136-001-007 configuration and is relevant when the controller must operate as a slave device on an existing PROFIBUS-DP network. Integration still depends on the network configuration, device addressing, master configuration, and applicable communication settings.
The controller also provides E-Bus connections for expansion with compatible MOOG modules. The documented expansion capability supports up to seven additional modules, so the installed expansion arrangement should be confirmed when planning replacement or system modification.
Configuration and programming use MOOG Axis Control Software (MACS), which is based on CODESYS and supports IEC 61131 programming. For maintenance or replacement, the application program, hardware configuration, communication parameters, axis assignments, and feedback settings should be preserved or reconfigured as required. The ordering number identifies the controller configuration but does not by itself establish that an existing machine project or parameter set can be transferred without adjustment.
Applications & System Role
The D136-001-007 functions as a programmable motion controller within a MOOG M3000 automation-system installation. It coordinates motion-control functions with PLC logic, field signals, position feedback, and industrial communication interfaces.
Its analog I/O, configurable digital I/O, and encoder/SSI feedback interfaces support closed-loop control applications involving electric or hydraulic motion axes. The PROFIBUS-DP slave interface is particularly relevant where the controller must exchange process data with a PROFIBUS-DP master in the machine-control architecture. The controller’s role is therefore determined by the installed MOOG application, connected feedback devices, expansion modules, and communication configuration.
FAQ
What is the MOOG D136-001-007?
The MOOG D136-001-007 is an MSC I programmable motion controller with integrated PLC functionality, analog and digital I/O, position-feedback interfaces, and a PROFIBUS-DP slave interface.
Which MOOG system family does the D136-001-007 belong to?
It belongs to the MOOG MSC I motion-controller family within the M3000 automation-system architecture.
What I/O does the D136-001-007 provide?
It provides eight 16-bit analog inputs, two 16-bit analog outputs, and eight digital I/O points that can be individually configured as inputs or outputs.
Which position-feedback interfaces does the controller support?
The controller provides two position-transducer interfaces that support incremental encoder or SSI feedback.
What communication interfaces are available on the D136-001-007?
The controller provides 10BASE-T Ethernet, two independent CAN interfaces, two EIA-232 serial ports, and a PROFIBUS-DP slave interface.
What is the PROFIBUS-DP capability of the D136-001-007?
The controller includes a PROFIBUS-DP slave interface rated for communication speeds up to 12 Mbit/s.
Which engineering software is used with the D136-001-007?
MOOG Axis Control Software (MACS), based on CODESYS and supporting IEC 61131 programming, is used for controller programming and hardware configuration.
What power supply does the D136-001-007 require?
The controller electronics operate from a nominal 24 V DC supply within a documented range of 18–36 V DC.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626