Sale!

Motorola MVME167-33B 33 MHz VMEbus Single-Board Computer

  • Model: MVME167-33B
  • Brand: Motorola / Emerson
  • Series: MVME167 VMEbus Single-Board Computer (SBC)
  • Core Function: High-performance 32-bit embedded processing with integrated Ethernet, SCSI, serial communications, and VMEbus system controller capabilities.
  • Product Type: VMEbus Single-Board Computer
  • Key Specs: CPU: 33 MHz Motorola MC68040 | RAM: 16 MB Parity DRAM | Interfaces: Ethernet, SCSI, 4x Serial Ports, VMEbus A32/D32 Master/Slave
  • Condition: New Original / New Surplus (Refurbished parts avoided entirely).
  • Inventory Status: Mature/EOL legacy product line; strategic reserve stock vital for maintaining continuous operation in legacy industrial, defense, and automation systems.

Description

Key Technical Specifications

Parameter Value
Microprocessor Motorola MC68040 32-bit microprocessor (with integrated FPU and MMU) at 33 MHz
Main Memory (DRAM) 16 MB shared DRAM with hardware parity support
On-board NVRAM / Clock 8 KB battery-backed NVRAM and time-of-day clock
Flash / ROM Sockets On-board Flash memory and socketed EPROM/ROM configurations for monitor firmware
VMEbus Interface Full A32/D32 master/slave interface with system controller functions and requester/interrupter logic
Network & Storage I/O On-board Ethernet transceiver interface, SCSI bus interface with DMA controller
Serial / Parallel I/O Four EIA-232-D serial communication ports, Centronics compatible printer port
Power Requirements +5 V DC, +12 V DC, -12 V DC VME backplane rails
Form Factor Single-height 6U VME module architecture (233.4 mm x 160.0 mm)

 

Product Introduction & Supply Chain Strategy

The Motorola MVME167-33B is a robust single-board computer built on the VMEbus architecture, driven by a 33 MHz MC68040 processor and 16 MB of parity-protected DRAM. It integrates comprehensive networking, SCSI storage control, and serial communications onto a single 6U form factor. Systems in heavy industry, energy generation, and defense rely on this controller for mission-critical real-time processing.

Procuring this board as genuine New Surplus protects your legacy infrastructure from the high Total Cost of Ownership (TCO) caused by unexpected hardware failures. Refurbished VME cards frequently suffer from thermally degraded solder joints, oxidized bus contacts, and exhausted battery backups that lead to intermittent bus faults. Maintaining an authentic, factory-fresh spare module in reserve ensures rapid recovery and prevents prolonged downtime.

 

Installation & Configuration Guide

1.Pre-Installation (Prep & Safety):Tools needed: ESD wrist strap, flathead screwdriver.

Power down the VME rack completely and disconnect all external AC/DC power feeds. Put on a grounded ESD wrist strap before handling the board. Verify that onboard jumper configurations and firmware match your existing system layout.

Verification: Confirm chassis power indicators are completely dark and use a multimeter to verify 0 V across backplane power rails.

2.Removal:Hardware extraction.

Disconnect front-panel cables (Ethernet drop, SCSI leads, or serial connections). Loosen the top and bottom panel mounting screws and carefully slide the MVME167-33B straight out of the VME chassis slot.

Verification: Visually inspect the backplane P1 and P2 connector pins inside the target slot for proper alignment and absence of bent pins or debris.

3.Installation (Clone & Seat):Hardware mounting.

Align the edges of the new surplus board with the card guides of the designated VME slot. Push the board straight back until the connectors seat firmly into the backplane, then tighten the front panel retaining screws. Reconnect all communication lines.

Verification: Confirm that the module is completely flush with adjacent cards and securely locked into the rack architecture.

4.Power-On & Testing:System startup.

Restore main power to the VME chassis. Monitor the on-board diagnostic LEDs and console terminal output during the boot sequence to verify kernel initialization and memory check completion.

Verification: Check that the firmware monitor or operating system loads successfully without parity faults or bus timeout errors.

MVME167-33B

MVME167-33B

MVME167-33B

MVME167-33B

Firmware/Software Versions & Upgrade Notes

  • Firmware Configuration: Ensure system Flash memory and on-board monitor revisions match the requirements of your real-time operating system (RTOS) environment, such as VxWorks or OS-9.
  • Compatibility Notes: The board requires a compatible VME backplane configuration supporting A32/D32 master/slave transactions and proper bus termination.
  • Upgrade Risk Warning: Avoid altering jumper blocks or flashing firmware while the rack is powered. Always perform configuration changes on a static-safe workbench with power fully disconnected to prevent bus driver damage.

 

Frequently Asked Questions (FAQ)

Is this Motorola MVME167-33B board genuinely new and unused?

Yes. This unit is a Brand New Surplus item, preserved in original packaging with pristine backplane contacts, uncorroded pins, and zero operational service hours.

Why choose New Surplus over refurbished vintage boards?

Vintage computing hardware is highly vulnerable to component aging. Refurbished boards often feature heat-stressed capacitors, brittle traces, and exhausted backup batteries. New Surplus delivers maximum factory longevity and removes the threat of sudden component failure.

What warranty is included with this board?

Every unit includes a comprehensive 1-year replacement warranty, safeguarding your legacy hardware investment.

Can I hot-swap the MVME167-33B in an active VME chassis?

No. VMEbus architecture does not support hot-swapping. You must completely power down the chassis before inserting or extracting single-board computers to prevent severe electrical damage.

How do I manage battery backup replacement for the on-board clock/NVRAM?

The board incorporates an integrated time-of-day clock and NVRAM chip with a self-contained battery. For long-term shelf storage or post-installation service, verify that the battery voltage remains within nominal manufacturer parameters before live deployment.