Sale!

Motorola MVME5500-0163 1 GHz PowerPC VME SBC

  • Model: MVME5500-0163
  • Brand: Motorola / Emerson
  • Series: MVME5500 VMEbus Single-Board Computers
  • Core Function: High-performance VME embedded computing
  • Product Type: 6U VMEbus Single-Board Computer (SBC)
  • Key Specs: 1 GHz MPC7455 PowerPC, 512 MB ECC SDRAM, dual 64-bit PCI/PMC buses
  • ⚠️ Obsolete Model – Limited Stock Available
  • Condition: New Original / New Surplus
Categories: , , , , SKU: MVME5500-0163 Brand:

Description

Key Technical Specifications

Parameter Value
Processor Motorola/Freescale MPC7455 PowerPC
Processor speed 1 GHz
Cache 256 KB on-chip L2; 2 MB L3 cache
Vector processing AltiVec coprocessor
Main memory 512 MB 133 MHz ECC SDRAM
Flash memory 32 MB + 8 MB soldered Flash banks
VME interface Universe II VMEbus controller
PCI architecture Dual independent 64-bit PCI buses, 33/66 MHz
Expansion Two PMC sites; 64-bit PCI expansion mezzanine connector
Ethernet 1 x Gigabit Ethernet, 1 x 10/100BaseTX Ethernet
Serial ports Two multi-protocol serial ports, configurable RS-232/RS-422/RS-485
System controller Marvell GT-64260B host bridge
Power consumption Typical 6.62 A at +5 V; maximum 7.94 A at +5 V
Form factor 6U VME single-slot board

The MVME5500-0163 uses a 1 GHz MPC7455 processor with 512 MB ECC SDRAM and IEEE handles, according to the original Motorola/Emerson product documentation. Its dual independent 64-bit PCI buses, two PMC sites, Gigabit Ethernet, and Universe II VME interface make it a direct fit for legacy VME control, data-acquisition, and embedded-computing systems.

 

Product Introduction

The Motorola MVME5500-0163 is a 6U VMEbus single-board computer built around a 1 GHz MPC7455 PowerPC processor, 512 MB ECC SDRAM, and a Marvell GT-64260B host bridge. It serves data-intensive embedded applications in process control, test systems, communications, and legacy industrial automation platforms.

Compared with earlier MVME5100-class boards, the MVME5500-0163 adds Gigabit Ethernet, dual 64-bit 33/66 MHz PCI buses, two PMC sites, and an AltiVec-enabled MPC7455 processor. It occupies one VME slot even when configured with PMC or memory mezzanine hardware, which helps preserve limited chassis space in existing systems.

MVME5500-0163

MVME5500-0163

MVME5500-0163

MVME5500-0163

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
No LEDs on power-up Chassis power, fuse, or backplane fault ❌ Low Measure +5 V and +3.3 V at the VME backplane with a Fluke 115 or equivalent meter Verify PSU, fuses, and backplane seating before replacing the SBC
Board powers up but does not boot Corrupt Flash, boot-device issue, or firmware/configuration fault ✅ High Connect to the debug serial port and capture the boot messages Recover or reload firmware; replace the board if Flash or boot ROM is damaged
No network link Ethernet cable, switch port, PHY configuration, or driver issue ❌ Low Swap the Ethernet cable and switch port; check link LEDs Test both Ethernet ports before condemning the SBC
VME communication timeout VME address map, terminator, bus grant, or master/slave configuration mismatch ✅ High Inspect VME jumpers and confirm the address map against the system documentation Correct configuration first; do not assume the board is failed
Random resets or memory errors Poor backplane contact, overheating, or failing SDRAM ✅ Medium Reseat the board, clean contacts, check airflow, and run an extended memory test If ECC errors persist, replace the SBC
PMC module not recognized PMC seating, PCI bus configuration, or incompatible PMC card ❌ Low Reseat the PMC and test it in another known-good MVME5500 system Verify PMC compatibility and PCI bus settings
Intermittent operation after installation ESD damage, bent pins, or incomplete connector engagement ✅ High Power down, inspect P1/P2 and PMC connectors, and reseat with ESD protection Replace only after connector, power, and configuration checks pass

If the fault remains unresolved, send photos of the board, VME chassis, jumper settings, boot output, and diagnostic logs to technical support before ordering a replacement.

 

Frequently Asked Questions

Can I hot-swap the MVME5500-0163?
No. Treat it as a power-down replacement. Remove chassis power, wait for capacitors to discharge, use an ESD wrist strap, and reseat the board carefully. Hot insertion can damage the VME backplane, PMC cards, or the SBC itself.

Is this board obsolete?
Yes. Motorola originally produced the MVME5500 family, and the product line later moved through Emerson ownership. Original production has ended, so reliable supply generally comes from controlled surplus or tested refurbished inventory.

Will the MVME5500-0163 replace my existing MVME board?
It is intended as a migration path from MVME2300, MVME2400, MVME2600, MVME2700, and MVME5100 systems, but it is not a blind drop-in replacement in every application. Confirm your VME address map, PMC hardware, operating system, BSP, and firmware requirements before installation.

Will my program and configuration survive a board swap?
Not automatically. Application code may reside on Flash, a PMC storage device, a hard drive, or elsewhere in the VME chassis. Back up the boot image, configuration files, and any PMC/NVRAM settings before removing the original board.

Why is this surplus board less expensive than a factory-new unit?
The original manufacturer no longer produces it, so pricing reflects available surplus inventory rather than current OEM production. New Surplus stock is unused original product; it may have older date codes or shelf wear but should not have field-operating hours.

What should I check before ordering?
Photograph the old board’s jumpers, record its firmware/boot configuration, confirm the required memory configuration, and verify the PMC cards and VME backplane type. The MVME5500-0163 draws up to 7.94 A at +5 V, so confirm your chassis power budget before installation.

What warranty and testing are included?
Stock condition and warranty depend on the specific listing. For tested units, request the functional test report, boot-test evidence, Ethernet/VME verification results, and photos before shipment.