Sale!

MTL4850 32-Channel SIL3 HART Multiplexer

  • Model: MTL4850
  • Brand: Eaton / MTL
  • Series: MTL4850 HART Multiplexer System
  • Core Function: Multiplexes HART data from smart field devices
  • Product Type: 32-channel HART multiplexer / HART maintenance interface
  • Key Specs: 32 channels; HART Rev. 5–7; RS485 multidrop; SIL3 certified
  • Condition: New Original / New Surplus
  • ⚠️ Obsolete Model – Limited Stock Available
Categories: , , , , SKU: MTL4850 Brand:

Description

Key Technical Specifications

Parameter Value
Model MTL4850
Manufacturer Eaton / MTL
Product family MTL4850 HART Multiplexer System
Function Interfaces HART field devices with control, safety, and asset-management systems
HART channels 32 per module
Field-loop connections 64 total; two connections per channel
Supported HART devices HART Rev. 5, 6, and 7
Host interface RS485, 2-wire multidrop
Network capacity Up to 63 MTL4850 modules; up to 2,016 HART devices per RS485 network
RS485 baud rate 1,200; 9,600; 19,200; or 38,400 baud, auto-detected
Module addressing 8-bit interface, up to 64 addresses
HART modem configuration Single HART modem serving all 32 channels
Supply voltage 19 to 35 V DC
Current consumption 60 mA at 24 V DC ±10%
Power dissipation Less than 1.6 W at 24 V DC ±10%
Power protection Reverse-polarity protected; fused at 375 mA
Channel-to-channel isolation 50 V DC
Field-loop isolation 50 V DC
RS485 interface isolation 25 V DC
Operating temperature −40 to +70°C
Storage temperature −40 to +85°C
Relative humidity 5% to 95%, non-condensing
Dimensions 18 mm × 124 mm × 106.2 mm
Weight 0.125 kg
Functional safety SIL3 capable for connection to safety instrumented functions per IEC 61508
Certifications ATEX, IECEx, CSA, FM, FMC
Mounting environment Safe area or Zone 2 / Division 2 mounting location

The MTL4850 uses a single HART modem to service all 32 channels. If your maintenance workflow needs simultaneous HART access to several devices, consider the MTL4854, which provides four HART modems.

 

Product Introduction

The MTL4850 is an Eaton/MTL 32-channel SIL3 HART multiplexer that connects smart field devices to DCS, PLC, SIS, and HART asset-management software. It provides a two-way HART communications path without disturbing the underlying 4–20 mA analog signal, allowing configuration, calibration, diagnostics, and device monitoring from a single workstation.

It mounts on MTL connection units or backplanes, including systems used alongside MTL4500 intrinsic-safety isolators. Its RS485 multidrop architecture supports up to 63 modules and 2,016 HART devices on one network, making it a practical choice for large process plants and safety-related instrument loops.

MTL4850

MTL4850

MTL4850

MTL4850

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Module does not appear on RS485 network Incorrect RS485 wiring, duplicate address, or termination issue ✅ High Verify A/B polarity, module address, termination resistors, and cable shield; check for duplicate addresses Correct RS485 wiring and set a unique address before replacing the module
No LEDs on power-up 24 V DC supply failure, blown fuse, or reverse polarity ✅ High Measure 19–35 V DC at the module supply terminals; inspect the 375 mA fuse and supply polarity Restore supply or correct polarity before replacing the MTL4850
One HART device cannot communicate Field loop wiring, HART device fault, or loop loading issue ❌ Low Test the device directly with a handheld HART communicator at the field terminals Troubleshoot the field loop and HART device first
Multiple HART devices fail together MTL4850 module, backplane connection, or RS485 host fault ✅ High Check module seating, backplane connectors, and whether the fault follows the module when swapped Reseat or replace the MTL4850 if the fault follows it
HART communication is intermittent Cable shield, ground loop, excessive RS485 length, or baud-rate mismatch ✅ Medium Inspect shield termination and grounding; confirm total RS485 length and baud rate Correct cable shielding and verify host communication settings
Analog 4–20 mA signal is wrong Transmitter, loop power, IS barrier, or DCS input fault ❌ Low Measure loop current directly; the MTL4850 couples to the loop without changing the analog signal Do not replace the MTL4850 until the analog loop is verified
Safety loop diagnostic alarm Configuration mismatch, loss of communications, or field-device diagnostic event ✅ High Review the onboard event log and host-system diagnostics; compare configured and actual device data Resolve configuration or communications issue; retain event-log evidence

❗ Do not assume a failed MTL4850 when only one HART device is unreachable. The multiplexer shares one HART modem across 32 channels, but a single bad transmitter, loose loop terminal, or failed IS barrier is more common than a module fault.

If the problem persists after checking power, RS485 wiring, module seating, and field-loop health, contact technical support with photos of the module, backplane, RS485 network, and diagnostic or event logs.

 

Frequently Asked Questions

Can the MTL4850 be used in a SIL3 safety loop?
Yes. It is certified for use with safety-related subsystems under IEC 61508 and can be connected to instrument loops performing safety functions up to SIL3. Your final SIL calculation must still account for the complete loop, proof-test interval, and application-specific failure data.

How many HART devices can one MTL4850 handle?
One MTL4850 handles 32 HART field devices, using two field-loop connections per channel for 64 total connections. Up to 63 modules can share one RS485 network, supporting up to 2,016 devices.

Does the MTL4850 affect the 4–20 mA analog signal?
No. It couples to each loop through capacitors and provides HART communication without interrupting the analog signal. Verify the loop and IS barrier design during commissioning, but the MTL4850 itself is not intended to regulate or replace the analog measurement path.

Can I connect it directly to a PC?
Not usually by itself. The MTL4850 uses an RS485 2-wire multidrop interface, so you normally use an RS485-to-USB or RS485-to-Ethernet converter to connect it to a PC running HART instrument-management software.

What is the difference between the MTL4850 and MTL4854?
Both provide 32 HART channels, but the MTL4850 has one HART modem while the MTL4854 has four. The MTL4854 is better when you need simultaneous communication with multiple field devices; the MTL4850 is adequate for routine polling and maintenance access.

Can I mount it in a hazardous area?
No. The MTL4850 is designed for safe-area or Zone 2 / Division 2 mounting locations. For intrinsically safe field loops, mount it with compatible MTL4500-series isolators and use the appropriate backplane or connection system.

Why is New Surplus less expensive than factory-new stock?
New Surplus means genuine Eaton/MTL inventory manufactured earlier but not installed or commissioned. We inspect, document, and functionally verify each unit before shipment. It is not used, repaired, or refurbished stock unless clearly stated on the product page.