Sale!

NATIONAL INSTRUMENTS NI 9505 30 V 5 A H-Bridge Module

  • Model: NI 9505
  • Brand: National Instruments (NI)
  • Series: C Series Motion Control Modules
  • Core Function: Integrated H-bridge driver for controlling DC, stepper, and relay-driven loads in CompactRIO systems.
  • Product Type: 1-Channel Full H-Bridge Servo/Motor Drive
  • Key Specs: 30 V continuous voltage rating | 5 A maximum current | Built-in encoder feedback support
  • Condition: New Original / New Surplus (Never refurbished).
  • Inventory Status: Critical high-wear automation spare; recommended safety stock item for motion test benches and industrial actuation rigs.
Categories: , , , , SKU: 9505 Brand:

Description

Key Technical Specifications

Parameter Value
Manufacturer National Instruments
Series C Series I/O
Model Code NI 9505
Number of Channels 1 H-bridge channel
Max External Voltage 30 V DC
Continuous Output Current 5 A DC
Switching Frequency Up to 20 kHz
Encoder Inputs Single-ended or differential (A, B, Z)
Isolation Voltage 60 VDC continuous channel-to-earth ground
Operating Temperature −40 to 70°C

 

Product Introduction & Supply Chain Strategy

The National Instruments NI 9505 is a 1-channel, full H-bridge module designed for CompactRIO platforms, providing direct PWM control and current sensing for small DC motors, solenoids, and stepper actuators. It integrates drive electronics with onboard encoder feedback inputs to execute closed-loop motion control loops locally within the chassis.

Procuring this motion module as New Surplus secures operational reliability while controlling Total Cost of Ownership (TCO). Relying on second-hand power electronics introduces latent risks from degraded MOSFET switching stages and heat-stressed gate drivers. Stocking verified surplus hardware eliminates unexpected test bench downtime, avoiding prolonged project delays while bypassing extended OEM manufacturing lead times.

 

Installation & Configuration Guide

1.Pre-Installation (Prerequisite):Estimated time: 5 mins.

Power down the CompactRIO chassis and completely isolate external DC power rails connected to the motor drive terminals. Attach a grounded ESD wrist strap, verify zero voltage on the power lines using a multimeter, and inspect module pins.

2.Removal:Estimated time: 5 mins.

Depress the module release latches on the top and bottom of the housing. Pull the legacy NI 9505 module straight out from the chassis slot carefully to avoid bending backplane pins.

3.Installation (Clone & Seat):Estimated time: 5 mins.

Align the replacement NI 9505 module with the target chassis slot and press inward firmly until the locking latches click into place. Reconnect the front spring-terminal connector block securely, verifying tight wire retention.

4.Power-On & Testing:Estimated time: 10 mins.

Energize the system chassis and external motor power supply. Open NI Measurement & Automation Explorer (MAX) or your LabVIEW project environment to verify module recognition, check status LEDs, and run a low-current open-loop test to confirm motor response.

9505

9505

9505

9505

Firmware/Software Versions & Upgrade Notes

  • Recommended Version: Ensure your installed version of NI-Motion or NI-RIO drivers matches the software requirements for the NI 9505 module within your LabVIEW environment.
  • Compatibility Notes: The NI 9505 is fully supported across standard CompactRIO targets running LabVIEW Real-Time, but verify FPGA bitfile dependencies if your application uses custom personalities.
  • Risk Management: Avoid performing software or driver overhauls during active motion testing phases. Swapping matched hardware within a stable software ecosystem prevents configuration mismatches and unexpected drive faults.

 

Frequently Asked Questions (FAQ)

Is this motor drive module genuinely new or refurbished?

This product is a Brand New Surplus unit. It features original OEM packaging, zero wear on connector pins, and has never been installed in an active test bench or industrial facility. We strictly reject second-hand, salvaged, or refurbished components.

Why is buying New Surplus essential for power electronics modules?

Power driver modules handle high switching currents and thermal loads. Refurbished or used drives often have degraded gate-drive circuits or micro-fissured solder joints that fail prematurely under load. Buying New Surplus guarantees factory-grade lifespan and reliability.

Does replacing this module require recompiling my LabVIEW FPGA code?

If you are replacing an identical NI 9505 module within the same slot and chassis configuration, a full FPGA recompile is typically unnecessary. However, always verify project mappings in LabVIEW before deployment.

What warranty is included with this unit?

Every unit is backed by a comprehensive 1-year replacement warranty, validating our strict inbound quality control and electrical verification standards.

Can I hot-swap the NI 9505 module?

No. Hot-swapping power drive modules connected to live external DC voltage and inductive motor loads risks severe electrical arcing, backplane damage, and component failure. Always kill main power before handling the module.