Sale!

NI PXI-6123 500 kS/s/ch Differential Analog Input DAQ Module

Attribute Specification
Manufacturer National Instruments (NI)
Model PXI-6123
Product type Simultaneous-sampling multifunction DAQ module
Form factor 3U PXI module
Analog-input channels 8 differential
ADC architecture One 16-bit ADC per channel; simultaneous sampling
Resolution 16 bits
Maximum sampling rate 500 kS/s per channel
Minimum sampling rate No minimum
Categories: , , , , SKU: PXI-6123 Brand:

Description

Core Product Summary

The National Instruments PXI-6123 is a 3U PXI multifunction data-acquisition module with eight differential, simultaneously sampled analog-input channels. Each channel uses an independent 16-bit ADC and supports a maximum sampling rate of 500 kS/s per channel.

The module also provides eight TTL/CMOS digital I/O lines, two 24-bit counter/timers, analog and digital triggering, and a 68-pin SCSI-II I/O connector. It is available with 16 MS or 32 MS onboard analog-input memory, depending on the part-number configuration. NI-DAQmx provides the software interface for configuration, acquisition, digital I/O, and timing operations.

 

Key Technical Specifications

Attribute Specification
Manufacturer National Instruments (NI)
Model PXI-6123
Product type Simultaneous-sampling multifunction DAQ module
Form factor 3U PXI module
Analog-input channels 8 differential
ADC architecture One 16-bit ADC per channel; simultaneous sampling
Resolution 16 bits
Maximum sampling rate 500 kS/s per channel
Minimum sampling rate No minimum
Input ranges ±1.25 V, ±2.5 V, ±5 V, ±10 V
Input coupling DC
Input impedance 100 MΩ in parallel with 10 pF, AI+ to AI GND and AI− to AI GND
Input bias current ±2 pA typical, ±25 pA maximum
Maximum working voltage ±11 V on AI+ and AI− for all ranges, Measurement Category I
Overvoltage protection ±36 V on AI+ and AI−
Onboard input FIFO 16 MS or 32 MS, depending on part number
INL ±2 LSB maximum
DNL −1 LSB minimum, +1.5 LSB maximum, no missing codes
Digital I/O 8 bidirectional TTL/CMOS lines
Digital transfer rate 10 Mwords/s, where one word is 8 bits
Counter/timers 2 up/down counter/timers, 24-bit resolution
Frequency scaler 1 channel, 4-bit resolution
Counter base clocks 20 MHz and 100 kHz
Counter maximum source frequency 20 MHz
Analog trigger source All analog-input channels
Digital trigger compatibility TTL, rising or falling edge
PXI trigger lines PXI_Trig<0..6>
PXI star trigger 1
I/O connector 68-pin male SCSI-II
Dimensions 16.0 × 10.0 cm (6.3 × 3.9 in.), excluding connectors
Operating temperature 0 °C to 50 °C
Storage temperature −20 °C to 70 °C
Operating humidity 10% to 90% RH, noncondensing
Maximum altitude 2,000 m
Software NI-DAQmx

 

Engineering Selection Highlights

  • The PXI-6123 provides eight differential analog inputs with one ADC per channel, so all channels can be sampled simultaneously rather than through a multiplexed input architecture.
  • Its 500 kS/s per-channel rate defines the acquisition speed for each channel; the rate is not divided among channels.
  • The module supports four input ranges from ±1.25 V to ±10 V, allowing resolution and input protection to be matched to signal amplitude.
  • The 16 MS or 32 MS onboard FIFO enables buffered acquisition and is selected by the exact part-number configuration.
  • The 68-pin SCSI-II connector requires a compatible DAQ cable and terminal accessory; the connector carries analog inputs, digital I/O, timing, and power terminals.
  • The module includes two 24-bit counter/timers, digital triggering, PXI trigger lines, and a PXI star-trigger input, supporting event counting, pulse timing, and coordinated PXI acquisitions.
  • Its Measurement Category I rating and ±11 V maximum working voltage establish the signal-conditioning boundary; higher-voltage signals require external isolation or attenuation.
PXI-6123

PXI-6123

PXI-6123

PXI-6123

System Compatibility & Integration Requirements

Item / Dependency Verified Compatibility or Requirement Practical Note
Chassis format 3U PXI chassis The module is a PXI multifunction I/O module and uses the PXI bus interface.
Analog inputs Eight differential channels, AI<0..7> Differential connections require AI+ and AI− pairs referenced to AI GND.
Digital I/O P0.<0..7>, TTL/CMOS Lines power up as high-impedance inputs.
Timing and triggering PFI 0–9, CTR 0/1, FREQ OUT, PXI trigger bus PFI terminals provide flexible routing for triggers, clocks, counter sources, gates, and outputs.
PXI synchronization PXI_Trig<0..6> and star trigger The module can use PXI trigger lines and a star trigger for multi-module coordination.
I/O connection 68-pin male SCSI-II connector Use a compatible 68-pin DAQ cable and terminal block or connector accessory.
Software NI-DAQmx NI-DAQmx configures and programs analog input, digital I/O, counters, and triggering.
Data transfer DMA, interrupts, or programmed I/O DMA supports scatter-gather transfers for acquisition and digital operations.
Cabling Shielded cabling Shielded cabling is required for the stated EMC compliance.

 

Dimensions, Mounting & Connection Notes

The PXI-6123 is a 3U PXI module measuring 16.0 cm high by 10.0 cm deep, excluding connectors. It installs in a 3U PXI chassis and connects to external signals through a 68-pin male SCSI-II connector.

The module requires 1.9 A at +5 VDC, 1.55 A at +3.3 VDC, and 81 mA at −12 VDC. The I/O connector can supply +4.65 to +5.25 VDC at up to 1 A for compatible external circuitry.

The analog-input terminals are rated for Measurement Category I use only and must not be used for Measurement Category II, III, or IV measurements. The AI+ and AI− terminals have a maximum working voltage of ±11 V for all ranges and ±36 V overvoltage protection. The module is specified for indoor use at Pollution Degree 2, up to 2,000 m altitude.

 

Applications & System Role

The PXI-6123 functions as a high-resolution, simultaneous-sampling acquisition and timing module within a PXI-based test or measurement system. Its eight independent ADCs make it suitable when relative timing among multiple voltage signals matters, such as multi-channel transient capture, frequency-domain measurements, and synchronized signal comparison.

NI identifies IF digitization, transient recording, telecom manufacturing test for ISDN, ADSL, and POTS, ultrasound and sonar testing, and high-energy physics as application contexts for the PXI-6123. Its differential inputs, 16-bit resolution, 500 kS/s per-channel rate, and large onboard memory support these signal-acquisition roles.

The digital I/O, counter/timers, and trigger routing extend the module beyond voltage acquisition. It can coordinate acquisitions with external events, generate timing signals, count pulses, and participate in PXI-based multi-instrument synchronization.

 

FAQ

What is the NI PXI-6123?
The NI PXI-6123 is a 3U PXI simultaneous-sampling multifunction data-acquisition module with eight differential 16-bit analog inputs, eight digital I/O lines, and two 24-bit counter/timers.

How many analog-input channels does the PXI-6123 have?
It has eight differential analog-input channels, AI<0..7>.

What is the maximum sampling rate?
The maximum sampling rate is 500 kS/s per channel.

Does the PXI-6123 sample channels simultaneously?
Yes. It uses one 16-bit ADC per channel, allowing all eight analog inputs to be sampled simultaneously.

What input voltage ranges are supported?
The module supports ±1.25 V, ±2.5 V, ±5 V, and ±10 V input ranges.

How much onboard memory does it have?
The PXI-6123 is available with either 16 MS or 32 MS of onboard analog-input FIFO memory, depending on the part-number configuration.

What type of connector does the PXI-6123 use?
It uses a 68-pin male SCSI-II I/O connector.

What software is used to program the PXI-6123?
NI-DAQmx is the software driver and configuration utility used to program and operate the module.