Description
Key Technical Specifications
| Parameter | Specification |
|---|---|
| Manufacturer | NOVOTRON Industrie-Automation GmbH |
| Full Model | ND32-5610V16 |
| Base Drive Model | ND32-5610 |
| Product Family | NOVODRIVE ND32 |
| Product Type | AC servo converter |
| Rated Supply Voltage | 400 V AC |
| Input Voltage Range | 400 V AC ±10% |
| Input Frequency | 50/60 Hz |
| Input Phases | 3 |
| Connected Load at Rated Current | 7 kVA |
| Rated Output Power | 5 kW |
| Rated Motor Current | 10 A RMS |
| Peak Motor Current | 20 A RMS |
| Rated Output Voltage | 500 V RMS |
| Output Phases | 3 |
| DC Link Voltage | 560 V DC |
| Overvoltage Shutdown Threshold | 720 V DC |
| Undervoltage Shutdown Threshold | 200 V DC |
| Switching Frequency | 4.9 kHz |
| External Signal Supply | 24 V DC ±15%, 1 A, stabilized and grounded |
| Signal Supply Power Consumption | 24 W with no outputs actuated; an additional 2.5 W per actuated output |
| Three-Phase Fuse Recommendation | 3 × 20 A, subject to OEM instructions and system design |
| Compact-Housing Dimensions | 331 × 180 × 87 mm |
| Compact-Housing Weight | Approximately 3.8 kg |
| Control Functions | Position, speed, and torque control |
| Feedback Options | Resolver, digital encoder, sine encoder, or Hall sensor, depending on configuration |
| Communication | NOVOBUS over serial or CAN; CANopen available on request for the family |
| Product Lifecycle | ND32 is an earlier generation; NOVOTRON identifies ND40 as its successor family |
Sources: Official NOVOTRON ND32 datasheet, ND31/ND32 technical documentation, and ND30 series product page.
Important specification distinction: The 10 A rating is the nominal motor current for the ND32-5610. The 20 A peak rating is not a continuous-current rating. Actual permissible current depends on the manufacturer’s thermal limits, operating conditions, and configuration.
Product Introduction
The NOVOTRON ND32-5610V16 is identified as a variant of the ND32 servo converter family, designed to control compatible brushless servo motors and linear motors. The documented ND32-5610 base model uses a 400 V three-phase supply and provides 5 kW rated output power, 10 A rated motor current, and 20 A peak motor current.
The ND32 platform provides position, speed, and torque control, with configurable feedback and command interfaces. Its legacy status makes exact model identification important when replacing an existing drive. Confirm the V16 suffix, motor feedback type, communication configuration, and parameter compatibility before commissioning.

ND32-5610V16

ND32-5610V16
Installation & Configuration Guide
The ND32-5610 is a high-voltage servo converter. Installation requires qualified electrical personnel familiar with servo drives and the machine’s safety procedures. The following steps are a general replacement workflow; the NOVOTRON manual takes precedence.
Stage 1: Pre-Installation Preparation
Estimated hands-on time: 20–30 minutes, excluding shutdown and backup time.
- Notify operations and secure the machine against unexpected movement.
- Apply lockout/tagout (LOTO) to the main supply and all auxiliary power sources.
- Verify that the DC link has discharged to a safe level using the OEM procedure and a suitably rated meter. Do not rely solely on the elapsed time after shutdown.
- Record the complete drive designation, including
V16, and photograph the nameplate and terminal arrangement. - Back up the existing drive parameters and document motor data, feedback configuration, control mode, and communication settings.
- Record the motor power, rated current, encoder or resolver type, and any brake or temperature-sensor connections.
- Obtain the correct ND31/ND32 basic-device manual and confirm that the replacement matches the existing mechanical format and interface configuration.
Required equipment: Appropriate insulated tools, a suitably rated multimeter, ESD protection for exposed electronics, wire labels, and the applicable OEM documentation.
⚠️ Do not open or handle the power stage until the DC-link discharge procedure has been completed and the safe voltage has been verified.
Stage 2: Removing the Existing Drive
Estimated hands-on time: 15–30 minutes.
- Verify electrical isolation and confirm the DC link is discharged.
- Label the incoming three-phase supply, motor output, feedback connector, signal supply, and communication connections.
- Photograph all connector positions and record the existing wiring configuration.
- Disconnect the wiring according to the manual. Do not pull on cable conductors or force connector locks.
- Release the specified mounting hardware and remove the unit carefully.
- Inspect the cabinet, cooling arrangement, connectors, and grounding points for overheating, contamination, or damage.
- Retain the original drive and its configuration records until the replacement passes acceptance testing.
Stage 3: Installing the Replacement
Estimated hands-on time: 20–40 minutes.
- Confirm that the replacement is the correct ND32-5610 variant and that the meaning of the
V16suffix has been established. - Verify the three-phase input rating, motor current, motor compatibility, and mounting arrangement.
- Mount the drive according to the OEM mechanical drawing and specified clearance requirements.
- Connect protective earth and the supply conductors according to the wiring diagram.
- Connect the motor and feedback devices using the verified terminal assignments.
- Reconnect the 24 V DC signal supply and communication interfaces as specified in the manual.
- Check motor phase connections, feedback polarity, cable shielding, grounding, and any brake or temperature-sensor wiring.
- Restore the documented drive parameters only after confirming compatibility with the replacement hardware and firmware.
Pre-commissioning checklist
Stage 4: Power-On and Functional Testing
Estimated hands-on time: 30–60 minutes, depending on the machine and commissioning requirements.
- Complete the required electrical inspections before energizing the drive.
- Confirm that the motor is mechanically safe and that the machine’s travel limits and safety interlocks are active.
- Energize the drive following the OEM startup sequence.
- Check status indicators and diagnostic messages against the manual.
- Establish communication with the drive using the supported NOVOTRON configuration interface.
- Verify the motor and feedback parameters before enabling the power stage.
- Test the selected control mode and command interface using the approved commissioning procedure.
- Perform a controlled low-speed movement test and verify direction, feedback response, and stopping behavior.
- Test the application under progressively representative operating conditions without exceeding the motor or drive ratings.
- Record parameter settings, diagnostic results, and acceptance-test findings.
⚠️ Do not enable motion if the feedback configuration, motor phase sequence, or direction of rotation is uncertain. Incorrect feedback settings can cause unexpected movement or loss of position control.
Frequently Asked Questions (FAQ)
Q1: What is the NOVOTRON ND32-5610V16 used for?
It is listed as an ND32-family servo converter variant. The underlying ND32-5610 model controls compatible servo motors and supports position, speed, and torque control. The exact V16 configuration should be verified against the physical nameplate or manufacturer records.
Q2: What are the rated power and current?
The official ND32 datasheet lists 5 kW rated output power, 10 A RMS rated motor current, and 20 A RMS peak motor current for the ND32-5610. The peak rating must not be used as a continuous operating rating.
Q3: What supply voltage does this servo converter require?
The base ND32-5610 requires a 400 V AC three-phase supply with a specified range of 400 V ±10%, at 50/60 Hz. The drive also requires a separate external 24 V DC signal supply. Verify the exact wiring and protection requirements in the OEM manual before energizing the unit.
Q4: Can the -5610V16 replace?
Not automatically. The base model designation suggests a relationship, but the V16 suffix is not explained in the official datasheet reviewed. Confirm hardware revision, firmware, connector configuration, feedback options, and parameter compatibility before treating the units as interchangeable.
Q5: Which communication protocols does the ND32 support?
The ND31/ND32 documentation describes the NOVOBUS protocol over serial and CAN interfaces. CANopen is available on request for the product family. Do not assume that every ND32-5610V16 unit includes the same communication options; verify the installed interface and configuration.
Q6: Is the NOVOTRON ND32-5610V16 obsolete?
The ND32 is an earlier-generation product family. NOVOTRON identifies the NOVODRIVE ND40 family as its successor, while also stating that earlier ND31 and ND32 products remain available through its product offering. Current availability of the exact V16 variant should be confirmed directly with the manufacturer or supplier.
Q7: What should I verify before purchasing a replacement?
Request the following before placing an order:
- A photograph of the complete model and revision label.
- Confirmation of the rated power and current.
- Verification of the installed feedback and communication interfaces.
- Confirmation of condition: new original, new surplus, or refurbished.
- Available functional-test records and warranty terms.
- Current stock status and dispatch lead time.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626