Sale!

RELIANCE 0-57C407-4H DCS 5000 Processor Module

Parameter Documented information
Manufacturer Reliance Electric
Part number 0-57C407-4H
Base model 57C407
Product designation DCS 5000 Processor Module
Control platform DCS 5000
Rack architecture Multibus backplane
Compatible power supply 57C493
Categories: , , , , SKU: 0-57C407-4H Brand:

Description

Core Product Summary

The RELIANCE 0-57C407-4H is identified with the 57C407 DCS 5000 Processor Module. It serves as a processor component in the Reliance DCS 5000 control platform, operating within a rack-based architecture that uses a Multibus backplane for communication among installed modules.

The processor is associated with dedicated DCS 5000 programming software and specific power-supply requirements. Its use should be evaluated against the existing rack configuration rather than treated as a general-purpose AutoMax processor replacement.

 

Key Technical Specifications

Parameter Documented information
Manufacturer Reliance Electric
Part number 0-57C407-4H
Base model 57C407
Product designation DCS 5000 Processor Module
Control platform DCS 5000
Rack architecture Multibus backplane
Compatible power supply 57C493
Programming environment ReSource DCS 5000 Programming Executive
Related battery backup 57C492
Communication interface Processor communication ports; RS-232 isolation support documented
Instruction manual references J-3650, J-3668, J-3692

The specifications above describe the documented 57C407 platform. Electrical ratings, memory capacity, processor speed, firmware version, and revision-specific details for the -4H suffix have not been independently verified.

 

Detailed Product Overview

The RELIANCE 0-57C407-4H belongs to the DCS 5000 processor family used in Reliance Electric industrial control systems. The 57C407 is identified in Reliance documentation as a DCS 5000 Processor Module, placing it within the central processing layer of the rack-based controller architecture.

The DCS 5000 rack uses a Multibus backplane to provide local communication between installed processor and control modules. This architecture allows the processor to operate as part of a coordinated control system rather than as an independent field I/O device.

Power configuration is an important consideration. Reliance documentation specifies the 57C493 power supply for the 57C407 processor. It also distinguishes DCS 5000 processors from AutoMax processors: the two processor types must not be mixed in the same rack.

For maintenance teams, these distinctions are essential when evaluating a replacement. A matching base model alone does not establish compatibility with every rack, power supply, or software configuration. The complete part number and installed system arrangement should be checked before procurement and commissioning.

0-57C407-4H

0-57C407-4H

0-57C407-4H

0-57C407-4H

System Compatibility and Integration Requirements

System component Documented relationship
57C493 Power Supply Specified for use with the 57C407 DCS 5000 Processor
DCS 5000 rack Provides the mounting structure and Multibus backplane
57C492 Battery Back-Up Used when a 57C407 processor is installed in the rack
57C384 cable Associated with the 57C492 Battery Back-Up
ReSource DCS 5000 software Programming environment for the 57C407
57C382 Isolation Short Haul Modem Provides isolation for DCS 5000 processor communication ports under specified installation conditions

Important rack restriction: Reliance documentation states that DCS 5000 and AutoMax processors cannot be mixed in one rack. The 57C407 should therefore be evaluated against the existing DCS 5000 rack and power-supply configuration.

 

Installation and Maintenance Considerations

Before replacing a 57C407 processor, maintenance personnel should verify the following:

  1. Part-number verification: Compare the complete 0-57C407-4H designation and revision with the installed unit.
  2. Power-supply compatibility: Confirm that the rack uses the specified 57C493 power supply.
  3. Rack configuration: Verify that the rack contains the correct processor family and that AutoMax processors are not mixed with DCS 5000 processors.
  4. Battery backup: Check the 57C492 battery backup arrangement and associated 57C384 cable where applicable.
  5. Programming environment: Confirm that the available ReSource software and system documentation match the DCS 5000 installation.
  6. Communication isolation: Review the serial communication wiring conditions. Reliance documentation describes the 57C382 isolation modem for situations involving cable lengths greater than 10 feet or communication grounds tied to earth ground.

Follow the applicable equipment manuals and electrical isolation procedures before removing or installing the processor. Static-sensitive components should be handled using appropriate ESD precautions.

 

Frequently Asked Questions

1. What is the RELIANCE 0-57C407-4H?

It is a Reliance Electric processor module associated with the 57C407 DCS 5000 Processor designation.

2. Is the 57C407 an AutoMax processor?

The 57C407 is identified as a DCS 5000 Processor. Reliance documentation distinguishes it from the 57C430 AutoMax Processor and prohibits mixing the two processor types in one rack.

3. Which power supply is specified for the 57C407?

The Reliance AutoMax Power Supply Modules and Racks documentation specifies the 57C493 power supply for the 57C407 DCS 5000 Processor.

4. Does the 57C407 require a battery backup?

Reliance documentation identifies the 57C492 Battery Back-Up as applicable when a 57C407 processor is installed in the rack. The 57C384 cable is used to connect the backup unit.

5. Which programming software is associated with the 57C407?

The processor is associated with ReSource DCS 5000 Programming Executive software. The specific software version should be checked against the installed controller configuration.

6. Is the 0-57C407-4H interchangeable with other 57C407 revisions?

Interchangeability of the -4H revision with other revisions has not been established by the available OEM documentation. Verify the complete part number and system requirements before replacement.