Description
3. Key Technical Specifications
- Input voltage: 90–264 VAC / 130–350 VDC
- Input frequency: 50/60 Hz
- Power factor correction: Active PFC
- Output power: Approx. 224 W (typical)
- Typical outputs: +5 V (high current), +12 V, –12 V (exact currents depend on variant)
- Ripple: Very low (<10 mVpp on many versions)
- Form factor: 19-inch rack, 6U height, 8 or 12 HP width, depth approx. 172 mm
- Protection: Overload, short-circuit, over-voltage
- Signaling: VMEbus-compatible status signals (e.g., Output Voltage OK)
- Redundancy: Supports parallel / redundant operation with decoupling diodes on many versions
- Cooling: Internal fan or convection depending on exact variant
- Operating temperature: Typically 0 °C to +40 °C or wider industrial range (confirm on unit)
- Note: Exact output currents, order number (e.g., 13190020, 13100-203), and any special options must be verified against the unit label.
4. Product Introduction
The Schroff MPS022 is a 19-inch rack-mount AC/DC power supply designed for VMEbus systems. It accepts a wide AC or DC input range and delivers clean, regulated multi-voltage DC outputs suitable for powering CPU, I/O, and communication modules in industrial control racks.
Engineers use the MPS022 in automation, energy, and transportation systems where reliable, low-ripple power and the ability to operate in redundant configurations are required. Its modular design allows straightforward integration into standard 6U VMEbus chassis.

MPS022

MPS022
5. Troubleshooting Quick Reference
| Symptom | Possible Cause | Relevance to this Part | Quick Check Method | Recommendation |
|---|---|---|---|---|
| No output voltage | Input power missing or internal failure | ✅ High | Measure input voltage and check front-panel status | Verify input supply; replace module if input is present and outputs remain zero |
| One or more outputs low or missing | Overload or failed output stage | ✅ High | Measure each output voltage under load | Reduce load or replace the power supply |
| High ripple or noisy outputs | Failing capacitors or fan issue | ✅ Medium | Scope the outputs and check cooling | Replace the module |
| System reports power fault | Status signal (Voltage OK) not asserted | ✅ High | Check VMEbus status lines and connector seating | Reseat module; verify signaling connections |
| Module overheats | Blocked airflow or high ambient temperature | ✅ Medium | Inspect fan (if present) and cabinet ventilation | Improve cooling; replace if fan has failed |
| Cannot achieve redundancy | Decoupling diodes or current-sharing not enabled | ✅ Medium | Verify wiring and configuration for parallel operation | Follow manufacturer redundancy guidelines |
If the issue cannot be isolated, photograph the module (including labels and any status indicators) and contact technical support with the full order number.
6. Frequently Asked Questions (FAQ)
Q: What systems is the MPS022 designed for?
A: It is a 19-inch rack-mount power supply primarily intended for VMEbus systems, commonly used in industrial automation, energy, and control racks.
Q: What input voltages does it accept?
A: Wide-range input: 90–264 VAC or 130–350 VDC, with active power factor correction.
Q: What are the typical output voltages?
A: Most versions provide multi-output rails such as +5 V (main high-current rail), +12 V, and –12 V. Exact currents depend on the specific order number.
Q: Can multiple MPS022 units be used for redundancy?
A: Yes. Many versions support parallel/redundant operation with integrated decoupling diodes and current sharing.
Q: Is the module hot-swappable?
A: In properly designed redundant systems it can support hot-swap, but always follow the system manufacturer’s procedures and safety rules.
Q: Are there different variants of the MPS022?
A: Yes. Different order numbers (e.g., 13190020, 13100-203) may vary slightly in output currents, cooling, or options. Always match the exact part number of the installed unit.
Q: What condition and warranty do you offer?
A: We supply New Original / New Surplus stock. Units are inspected for basic functionality. Standard coverage is a 1-year warranty against defects. Provide the complete model MPS022 and any order/style number when ordering or requesting support.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626