Sale!

SEM MT30R4-37 Permanent Magnet DC Servo Motor

  • Model: MT30R4-37
  • Brand: SEM (SEM Servo Motors)
  • Series: MT30R4 Permanent Magnet DC Servomotor Series
  • Core Function: Brushed DC servo axis drive motor for positioning
  • Product Type: Servo Motor
  • Key Specs: 140 VDC, 3.2 Nm continuous torque, 3800 RPM
  • Mounting: Flange mount, keyed shaft
  • ⚠️ Obsolete Model — Limited Stock Available
  • Condition: New Original / New Surplus (Refurbished units also available, tested)
Categories: , , , , SKU: MT30R4-37 Brand:

Description

Key Technical Specifications

Parameter Value
Motor Type Permanent Magnet (PM) Brushed DC Servomotor
Rated Voltage 140 VDC
Rated Speed 3800 RPM
Continuous Torque 3.2 Nm
Shaft Type Keyed shaft, Ø16 mm
Mounting Flange mount, Ø100 mm flange
Encoder/Feedback Tachometer/encoder per build — verify against nameplate
Protection Rating IP44 / IP65 (per variant)
Insulation Class Class F typical — confirm on nameplate
Weight Approx. 2.2 kg (4.9 lb)
Condition New Surplus / Refurbished (tested)
Availability In stock, ships in 1–2 business days

Verify exact feedback type and pinout against your original nameplate before ordering — SEM built several MT30R4 variants with different tach and encoder configurations.

 

Product Introduction

The SEM MT30R4-37 is a permanent magnet brushed DC servomotor, built for closed-loop position and speed control on machine tools, packaging lines, and motion axes in industrial automation. It delivers 3.2 Nm continuous torque at 140 VDC with a rated speed of 3800 RPM, flange-mounted with a keyed shaft for direct mechanical interchange.

SEM discontinued this series, so the MT30R4-37 is now a replacement-part hunt for most plants. Our New Surplus stock carries the original OEM build spec — same winding, same feedback configuration as the unit on your machine. That matters: brushed DC servo systems are tolerant of drive swaps but unforgiving of feedback mismatches, and a drop-in identical unit beats retrofitting a modern AC servo plus drive and cable changes. Tested, documented, and shipped with a 1-year warranty.

MT30R4-37

MT30R4-37

MT30R4-37

MT30R4-37

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Motor won’t rotate, no fault on drive Power stage off, wiring break, blown fuse ❌ Low Measure 140 VDC at drive output terminals; check fuses and contactor Check drive output and cabling before condemning the motor
Motor runs rough, sparks heavily at brushes Worn brushes, dirty commutator ✅ High Remove brush caps; inspect brush length (replace below ~1/3 original) and commutator surface Replace brushes or send for commutator service — often fixes the unit
Motor overheats under normal load Shorted/worn armature, wrong drive current limit ✅ Medium Measure winding resistance phase-to-phase, compare against nameplate; check drive current limit settings If resistance is out of spec, replace or rewind
Erratic speed, drive faults intermittently Feedback (tach/encoder) failure, broken coupling ✅ High Scope tach/encoder output while rotating shaft by hand — look for clean, continuous signal Replace feedback unit or motor if feedback is integral
Grinding noise, excessive vibration Worn bearings ✅ High Spin shaft by hand with power off; feel for notchy or gritty rotation, check axial play Bearing replacement — straightforward workshop job or send to repair
No holding torque, drifts at standstill Drive tuning or runaway, not the motor ❌ Low Check drive enable signal and tuning loop gains Motor rarely the cause — review drive parameters first

Stuck at 3:00 AM? Send us photos of the nameplate, the drive model, and any fault logs. We’ll tell you straight whether it’s the motor or something upstream.

 

Frequently Asked Questions (FAQ)

Is the SEM MT30R4-37 still in production?
No. SEM discontinued this series years ago, so everything on the market is New Surplus, refurbished, or used. Our New Surplus units are unused OEM stock in original or equivalent packaging — not copies, not rewound clones. Refurbished units are ones we ran on a test bench under load before listing.

Is it a direct replacement for my existing MT30R4-37?
Mechanically, yes — same flange, same keyed Ø16 mm shaft, same mounting footprint. The one thing to verify is the feedback configuration. SEM shipped variants with different tachometer and encoder setups, and your drive is tuned to that feedback. Match your nameplate before ordering. If your unit has a tach only and you install an encoder variant, the drive won’t read it correctly. Send us a photo of your nameplate and we’ll confirm.

Will my drive settings survive the motor swap?
If you’re replacing like-for-like with the same feedback type, yes — the drive doesn’t care which physical motor is bolted on. If you switch feedback types, expect to retune the velocity loop. Honestly, that’s a hassle on older DC drives since some have trim pots instead of software parameters. Document pot positions before you touch anything.

Can I hot-swap the motor?
No. Kill the drive power and disconnect the armature leads first. You’re dealing with 140 VDC on the armature circuit, and disconnecting it under load will arc and can damage both the drive’s output stage and the new motor’s commutator. Lock out, tag out, verify zero volts at the terminals. This is a brushed DC machine — treat the armature circuit with the same respect as any DC bus.

Why is this cheaper than a new motor from the factory?
Because there isn’t a new one from the factory — the series is obsolete. You’re paying for genuine OEM surplus or a properly refurbished unit instead of a full AC servo retrofit. A retrofit means a new motor, a new drive, new encoder cabling, and re-tuning the axis. That can run five to ten times the cost of a drop-in MT30R4-37. For keeping a legacy machine running, the surplus route is the economical call — just buy from someone who actually tests before shipping.

How do you test these before shipping?
Each motor goes through Megger insulation testing at 500 V (must read above 10 MΩ), winding resistance verification against nameplate values, brush and commutator inspection, and a supervised spin test on a DC drive bench at rated voltage with thermal monitoring over a multi-hour run. Feedback signals are scoped for clean output. Test reports and videos are available on request.

What’s the warranty?
1-year warranty on New Surplus and Refurbished units, covering functional failure under normal use. It doesn’t cover physical damage from crash events, water ingress, or brushes — brushes are consumables and are checked at shipment, but they wear by design.