Sale!

SEM MTS30M4-38C Permanent-Magnet Brushed Servo Motor

  • Model: MTS30M4-38C
  • Brand: SEM / Servo Dynamics
  • Series: MT30 / MTS30 DC Servo Motor
  • Core Function: Closed-loop DC servo positioning and speed control
  • Product Type: Permanent-magnet brushed DC servo motor
  • Key Specs: 140 V DC; 3,700 RPM maximum speed; 26 lb-in continuous stall torque
  • Condition: New Original / New Surplus
  • ⚠️ Obsolete Model – Limited Stock Available
Categories: , , , , SKU: MTS30M4-38C Brand:

Description

Key Technical Specifications

Parameter Value
Model MTS30M4-38C
Manufacturer SEM / Servo Dynamics
Product family MT30 / MTS30 DC Servo Motor
Motor type Permanent-magnet brushed DC servo motor
Rated voltage 140 V DC maximum terminal voltage
Maximum speed 3,700 RPM
Continuous stall torque, TENV 26 lb-in, approximately 2.94 Nm
Continuous stall torque, blower cooled 40 lb-in, approximately 4.52 Nm
Torque constant 0.35 Nm/A, approximately 3.1 lb-in/A
Voltage gradient 38 V per 1,000 RPM
Maximum armature current Approximately 8.6 A
Rotor inertia 0.0017 lb-in-s²
Feedback device Built-in tachogenerator; 1,000-line equivalent feedback, 7 V at 1,000 RPM
Feedback connection Flying leads
Brush construction Silver-graphite brushes
C-version construction Ceramic washers for extended service life
Mounting flange A1-B / SD55 square flange
Shaft Keyed shaft
Weight Approximately 14 lb, 6.35 kg
Operating environment Typically requires external protection in wet, dusty, or washdown environments
Typical drive compatibility Analog DC servo drives with armature-voltage and tachogenerator feedback

The C suffix identifies an updated construction revision within the MTS30M4-38 motor family. Confirm the motor nameplate, feedback wiring, and drive settings before substituting it for an A, B, or D revision.

 

Product Introduction

The SEM MTS30M4-38C is a permanent-magnet brushed DC servo motor for legacy machine tools, test rigs, material-handling equipment, and analog servo-control systems. It delivers 26 lb-in continuous stall torque in TENV service, reaches 3,700 RPM, and operates from a 140 V DC armature supply.

Its built-in tachogenerator supports an analog speed-feedback loop without adding an external encoder, making it a practical replacement for older SEM/Servo Dynamics drive systems. The C-version ceramic washer construction and silver-graphite brushes are intended to improve brush and bearing life in demanding industrial service.

 

Troubleshooting Quick Reference

Symptom Possible Cause Relevance to this Part Quick Check Method Recommendation
Motor will not rotate Open armature circuit, failed brushes, or drive fault ✅ High With power off, measure armature resistance and inspect brush holders; check drive output voltage Inspect brushes and armature before replacing the motor
Motor runs but has no torque Worn brushes, weak magnets, or excessive mechanical load ✅ High Measure armature current under load and inspect brush wear; compare against nameplate and drive limits Replace brushes if worn; verify mechanical load and coupling alignment
Speed unstable or hunting Tachogenerator fault, loose feedback wiring, or drive tuning issue ✅ High Measure tachogenerator output while rotating the shaft; inspect feedback shield and connections Repair tach feedback wiring or replace the motor if tach output is unstable
Motor overheats Continuous overload, blocked cooling, or excessive duty cycle ✅ High Measure armature current and motor temperature; verify load torque and duty cycle Reduce load, improve cooling, or resize the motor/drive
Brush sparking or arcing Worn brushes, contaminated commutator, or high ripple current ✅ High Inspect commutator surface and brush seating; check drive output ripple Clean or dress the commutator, replace brushes, and verify drive filtering
Position error or drift External encoder fault, coupling slip, or mechanical backlash ❌ Low Check external encoder counts and mechanical coupling; the MTS30M4-38C tach provides speed feedback, not absolute position Troubleshoot the external encoder and mechanical drivetrain first
Motor will not reach full speed Low supply voltage, drive current limit, or mechanical binding ✅ Medium Measure DC bus/armature voltage and current while commanding speed; check for binding Verify drive settings and mechanical load before replacing the motor

❗ Do not assume a failed MTS30M4-38C from poor speed stability alone. A loose tachogenerator lead, damaged shield, dirty commutator, or incorrectly tuned DC drive produces similar symptoms. Check the feedback loop and brushes first.

If the fault remains after checking brushes, commutator condition, armature resistance, tachogenerator output, and drive parameters, contact technical support with photos of the motor nameplate, brush assembly, feedback wiring, and drive fault logs.

MTS30M4-38C

MTS30M4-38C

MTS30M4-38C

MTS30M4-38C

Frequently Asked Questions

Can I replace an MTS30M4-38 with an MTS30M4-38C?
Usually yes, but verify the mechanical mounting, shaft dimensions, armature voltage, tachogenerator wiring, and drive tuning first. The C suffix identifies a construction revision, not necessarily an identical electrical or feedback interface across every production batch.

Does the MTS30M4-38C include an encoder?
The standard motor includes a tachogenerator for analog speed feedback, commonly specified as 1,000-line equivalent feedback or 7 V at 1,000 RPM. It does not inherently provide absolute position feedback; use an external encoder if the application requires position control.

What drive do I need for this motor?
Use a DC servo drive rated for 140 V DC armature output and the motor’s continuous and peak current requirements. The drive must accept tachogenerator feedback for speed-loop control or an external encoder for position-loop control.

Can I use it as a direct replacement for an AC servo motor?
No. This is a brushed DC servo motor with a tachogenerator, not an AC permanent-magnet synchronous servo motor. Do not connect it to an AC servo amplifier. Verify the existing drive type and feedback wiring before ordering.

Can I hot-swap the MTS30M4-38C?
No. Isolate and lock out the drive, wait for the DC bus to discharge, and verify zero voltage before disconnecting motor or feedback leads. Brushed DC servo systems can retain hazardous voltage in drive capacitors after shutdown.

How should I maintain it?
Inspect brushes and commutator at planned intervals, keep the commutator clean and dry, verify brush spring pressure, and check tachogenerator lead shielding. Avoid washdown exposure unless the motor is installed in a suitable protective enclosure.

Why is New Surplus less expensive than factory-new stock?
New Surplus means genuine SEM/Servo Dynamics inventory manufactured earlier but not installed or commissioned. We inspect, document, and functionally verify each unit before shipment. It is not used, repaired, or refurbished stock unless clearly stated on the product page.