WhatsApp: +86 16626708626
Email: 
Phone: +86 16626708626Description
Key Technical Specifications
| Parameter | Specification |
| Full Part Number | A413212 |
| Alternative Sub-ID | A413212-00, A413212-01 |
| System Compatibility | Valmet Damatic D3 / Damatic XD Distributed Control System |
| Module Type | Rack Power Supply Unit (PSU) |
| Input Voltage | 24 VDC nominal (or 115/230 VAC system rack feed) |
| Output Voltage Rails | Regulated +5 VDC (Logic), ±15 VDC (Analog I/O) backplane power |
| Form Factor | Metal-shielded modular rack insertion card |
| Cooling Method | Passive convection cooling |
| Connector Interface | High-current backplane edge connector |
| Protection Circuitry | Over-voltage, over-current, and thermal shutdown protection |
| Operating Temperature | 0°C to 60°C (32°F to 140°F) |
Product Introduction & Supply Chain Strategy
The Valmet A413212 is a central system power supply module engineered for legacy Valmet Damatic D3 and Damatic XD distributed control systems (DCS). Operating inside continuous pulp, paper, and power plants, it converts incoming station power into isolated, low-noise DC voltage rails required to energize rack processors, communication cards, and I/O channels.
This product is a Brand New Surplus unit. It is not used, not pulled from a decommissioned plant, and not refurbished. All modules undergo rigorous quality verification to ensure OEM-level reliability.
Securing an A413212 module as New Surplus provides a vital Total Cost of Ownership (TCO) buffer for plant operations. Power supply modules are high-wear components; buying refurbished units carries severe risks of degraded electrolytic capacitors, dried thermal grease, and voltage ripple that cause phantom controller resets. Saving 400 on a refurbished power supply can cost 50,000 in unplanned downtime when a power rail collapses during a production run. We recently saw a paper mill attempt to save procurement budget by buying a refurbished DCS power card. Two months later, capacitor breakdown caused a voltage spike that wiped out the adjacent processor card, stopping the main paper machine for 18 hours. Our pricing reflects the true cost of acquiring pristine New Surplus inventory globally, guaranteeing 100% power stability and complete peace of mind.
A413212
Installation & Configuration Guide
- Stage 1: Pre-Installation (Prep & Safety)
Isolate incoming rack power supply feeds and execute complete lock-out/tag-out procedures on the enclosure. Put on a grounded ESD wristband. Verify with a digital multimeter that no residual voltage remains on the rack power terminals before handling the module.
- Stage 2: Removal
Unscrew the front-panel retaining fasteners on the top and bottom of the module chassis. Slide the old A413212 unit straight forward out of the card rack along its guide rails, using steady pressure to disconnect the rear high-current backplane connector without twisting the card cage.
- Stage 3: Installation (Clone & Seat)
Inspect the backplane connector pins on the card slot for debris or damage. Align the metal housing of the New Surplus with the card guides, slide the unit into the rack until the rear connector meets the backplane, and press firmly until the front face sits flush. Tighten all retention screws securely.
- Stage 4: Power-On & Testing
Energize the main power feed to the rack cabinet. Observe the LED indicators on the front panel to confirm stable DC output status (solid green POWER OK / RUN). Measure output test points across the backplane if accessible to confirm +5 VDC and ±15 VDC rails sit within ±2% tolerances before clearing the station for process execution.
Firmware/Software Versions & Upgrade Notes
- Hardware Mapping: The is a hardware-level power converter and contains no programmable firmware or flash memory. It operates independently of control software revisions.
- Load Balancing Directives: When installed in redundant power rack configurations, ensure both primary and secondary power supply modules match input voltage ratings and load-sharing revisions to maintain seamless failover switching.
- Modification Warning: Never insert or pull the power supply module while the main rack backplane power feed is energized. Hot-swapping a main power supply without a validated redundant secondary module will instantly drop bus voltage, crashing all active DCS processing cards in the rack.
Frequently Asked Questions (FAQ)
- Q: Is this Valmet power supply module brand new surplus or a repaired unit?
A: This unit is 100% Brand New Surplus. It is not used, not repaired, and not pulled from a decommissioned process facility. It features untouched internal components, pristine gold-plated connector contacts, and original factory structural integrity.
- Q: Why avoid buying a cheaper refurbished power supply for a legacy DCS system?
A: Power supplies rely heavily on electrolytic capacitors, which dry out and fail over time even when idling on a shelf. Refurbished units retain aged internal capacitors that introduce micro-voltage drops and noise spikes into sensitive CPU logic, risking total system crashes that far outweigh short-term purchasing savings.
- Q: Is the Valmet power supply still manufactured by the OEM?
A: No, the Damatic D3 and Damatic XD control series are discontinued End-of-Life (EOL) platforms. Because factory manufacturing has ceased, maintaining 1 to 2 New Surplus power modules in on-site buffer stock is essential to prevent extended plant outages during hardware failures.
- Q: Does this module require internal jumper adjustments or setting configuration?
A: No, the is a factory-calibrated power module. It requires zero DIP switch or jumper configuration—simply align, seat into the rack backplane, and apply line power.
- Q: What warranty coverage applies to this New Surplus Valmet unit?
A: We cover this New Surplus unit with a comprehensive 1-year replacement warranty, providing complete operational reliability for your maintenance operations.
