Sale!

Vibro-Meter MPC4 200-510-078-115 Machinery Protection Card

  • Model: MPC4 200-510-078-115
  • Brand: Meggitt Vibro-Meter (Meggitt Sensing Systems)
  • Series: VM600 Machinery Protection System (MPS) Series
  • Core Function: High-precision vibration and mechanical protection monitoring for rotating machinery
  • Product Type: Rack-Mount Machinery Protection Card
  • Key Specs: 4 Dynamic Channels | 2 Speed Inputs | VME Bus Interface
  • Condition: New Original / New Surplus (Never refurbished).
  • Inventory Status: Mature/Active protection lifecycle status; essential spare parts buffer item required to prevent unplanned outages on critical turbines and compressors.
Categories: , , , , SKU: MPC4 200-510-078-115 Brand:

Description

Key Technical Specifications

Parameter Value
System Platform VM600 Series Machinery Protection System (MPS)
Dynamic Signal Inputs 4 channels (supporting acceleration, velocity, and displacement)
Speed (Tachometer) Inputs 2 channels (supporting proximity probes, magnetic pickups)
Frequency Range 0.1 Hz to 10 kHz
Signal Processing Digital Signal Processing (DSP) with programmable filtering
Communication Interface VME backplane bus, front RS-232 serial interface
Operating Temperature 0 to +65^\circC
Storage Temperature -25 to +85^\circC
Physical Format 6U Euro-card rack module form factor
Safety Compliance Designed for SIL-rated machinery protection environments

 

Product Introduction & Supply Chain Strategy

The Meggitt Vibro-Meter MPC4 (Part Number: 200-510-078-115) is a flexible, high-performance machinery protection card engineered as the central element of the VM600 rack-based monitoring system. It continuously processes dynamic vibration and speed inputs from critical rotating assets—such as industrial steam turbines, gas compressors, and large generators—delivering real-time protection and early fault detection.

Procuring this safety-critical protection module as a Brand New Surplus asset shields your plant against unexpected catastrophic machinery failures and costly unplanned outages. Sourcing genuine, factory-fresh hardware eliminates the hidden capacitor aging, calibration drift, and component wear inherent in used or repaired circuit cards, guaranteeing predictable Total Cost of Ownership (TCO) and absolute reliability across safety instrumentation loops.

MPC4 200-510-078-115

MPC4 200-510-078-115

MPC4 200-510-078-115

MPC4 200-510-078-115

Installation & Configuration Guide

  • Stage 1: Pre-Installation (Prep & Safety): Enforce strict lock-out/tag-out (LOTO) and machinery protection system (MPS) trip-bypass protocols before servicing the rack. Equip an electrostatic discharge (ESD) grounding wrist strap. Inspect backplane pin connectors for cleanliness and oxidation. Export and archive existing channel configuration files and alarm setpoints via VibroSight or associated software tools.
  • Stage 2: Removal: Loosen front-panel retaining screws. Extract the legacy MPC4 module smoothly along its rack guide rails, avoiding mechanical strain or bending of backplane connector pins.
  • Stage 3: Installation (Clone & Seat): Verify that hardware jumper settings and configuration options on the replacement unit match plant requirements. Align the card carefully with the 6U rack slot guides and push straight inward until firmly seated into the backplane connector. Secure captive front screws.
  • Stage 4: Power-On & Testing: Energize the rack power supplies. Monitor module status LEDs on the front panel for normal health checks (OK, Alert, Danger). Verify sensor bias voltages, input scaling, and relay trip setpoints using configuration software before returning the protection loop to active service.

 

Firmware/Software Versions & Upgrade Notes

  • Recommended Baseline: Match the configuration software version and module firmware baseline established for the plant’s active VM600 rack infrastructure.
  • Compatibility Notes: Ensure input scaling parameters (such as sensitivity in mV/mil or mV/mm/s) match the installed proximity or seismic sensors precisely upon replacement.
  • Upgrade Warning: Avoid simultaneous rack hardware replacements and major system software upgrades during active plant operations. Complete physical module swaps first, verify sensor signal acquisition stability, and schedule configuration modifications during planned unit outages.

 

Frequently Asked Questions (FAQ)

  • Are these protection cards truly new or refurbished?

    This unit is a Brand New Surplus part, preserved in factory-original packaging, completely unused, and never installed or repaired.

  • Why choose New Surplus over a cheaper refurbished unit?

    Refurbished protection cards frequently feature degraded analog filtering components and thermally stressed capacitors. Saving nominal capital on a used monitoring card risks false alarms or, worse, failure to detect severe mechanical degradation during active machine operation.

  • What is the strategic inventory plan for this module?

    Because rotating equipment protection is essential for avoiding catastrophic failures, maintaining at least 1 spare unit of the MPC4 on-site as buffer stock ensures rapid mean-time-to-repair (MTTR) during unexpected hardware faults.

  • Can the MPC4 be hot-swapped in the VM600 rack?

    While VM600 racks support modular card replacement, strict plant safety procedures, interlock overrides, and loop bypasses must always be executed prior to extraction to prevent accidental machine trips.

  • What warranty terms are included?

    Every New Surplus MPC4 200-510-078-115 unit is backed by a comprehensive 1-to-2 year operational warranty, assuring complete dependability for plant safety and machinery health architecture.