Description
Key Technical Specifications
| Parameter | Specification |
| Manufacturer | Yaskawa Electric Corporation |
| Module Type | System Control Rack Power Supply Module |
| Input Voltage Range | 100–240 V AC (\pm 10\%, 50/60 Hz) or 24 V DC system feed |
| Output Rails | Regulated low-noise DC outputs for logic CPU and I/O bus |
| Power Rating | 60 W nominal system logic capacity |
| Circuit Protection | Integrated overcurrent (OCP) and overvoltage (OVP) shutdown |
| Efficiency Rating | Industrial high-efficiency switching topology |
| Operating Temperature | 0 to +55 °C |
| Cooling Method | Natural convection / Chassis heat dissipation |
| Status Indicators | Front-panel LED display for POWER OK, ALARM, and Output Status |
Product Introduction & Supply Chain Strategy
This product is a Brand New Surplus unit. It is not used, not pulled from a decommissioned plant, and not refurbished. All modules undergo rigorous quality verification to ensure OEM-level reliability.
The Yaskawa JRMSP-PS60AV is a power supply module designed to deliver regulated, low-noise DC logic power across backplane buses in Yaskawa multi-axis motion and automation racks. It powers the central processing unit, communication interface cards, and local I/O handling boards, maintaining stable voltage rails under fluctuating industrial power conditions.
From a Total Cost of Ownership (TCO) perspective, stocking a New Surplus JRMSP-PS60AV serves as essential insurance against unpredicted facility shutdowns. A degraded power supply can drop logic rails or introduce voltage ripple, leading to intermittent CPU resets, communication dropouts, and unexplained machine faults. Refurbished power units often contain aged electrolytic capacitors near the end of their operational life, which are prone to thermal runaway under continuous duty. Securing a genuine New Surplus unit ensures full expected service life, eliminates lead time variability, and enables immediate drop-in restoration without modifying control panel wiring.

JRMSP-PS60AV

JRMSP-PS60AV
Installation & Configuration Guide
Stage 1: Pre-Installation (Prep & Safety)
- Execute full Lock-Out/Tag-Out (LOTO) procedures on the incoming main AC power feed and auxiliary 24 V DC supply breakers.
- Wait a minimum of 10 minutes to allow high-voltage input capacitors inside the power supply module to fully discharge below 50 V DC. Verify zero potential with a multimeter.
- Wear an ESD-grounded wrist strap connected to the enclosure’s ground bus bar before handling system hardware.
- Photograph all terminal wiring connections, line filter leads, and front-panel DIP or jumper configuration switches on the existing unit.
Stage 2: Removal
- Unthread the incoming power terminal connections or unplug the primary AC/DC input power harness.
- Loosen the top and bottom retaining thumbscrews securing the JRMSP-PS60AV module inside the chassis rack slot.
- Gently pull the module straight out along its chassis card guide rails to avoid putting strain on the rear backplane bus connectors.
Stage 3: Installation (Clone & Seat)
- Remove the New Surplus JRMSP-PS60AV from its anti-static shielding bag inside an ESD-safe workspace.
- Verify that any voltage selection jumpers or input DIP switches match the settings recorded from the failed unit.
- Align the power supply module with the designated rack card slot guides and slide it firmly inward until the backplane connectors fully seat. Tighten the retaining screws.
Stage 4: Power-On & Testing
- Reattach the input power wiring harness or terminal leads, verifying correct line, neutral, and ground terminations.
- Re-energize the incoming power breaker. Observe the front-panel status LEDs on the JRMSP-PS60AV.
- Verify that the “POWER OK” LED illuminates solid green and that secondary DC voltage rails measure within specified operational tolerances before enabling main system motor drives.
Firmware/Software Versions & Upgrade Notes
- System Compatibility: Purely hardware-driven power module designed for seamless plug-and-play integration across matching JRMSP rack configurations.
- Power Buffer Sizing: When replacing a power supply module in a fully loaded motion control rack, verify total system backplane current consumption to ensure a minimum 20% power overhead margin under peak processing loads.
- Hardware Revisions: Ensure the input line rating on the module match your facility’s power supply architecture (100–120 V AC, 200–240 V AC, or 24 V DC) prior to energizing to prevent input stage bridge rectifier failure.
Frequently Asked Questions (FAQ)
Q: Why is this New Surplus JRMSP-PS60AV priced higher than refurbished options online, but lower than OEM list prices?
A: Our price reflects the direct market value of supplying authentic, unused OEM hardware. Refurbished power supplies are typically harvested from old control panels and carry worn electrolytic capacitors and thermally degraded power transistors. While a refurbished unit may cost less initially, a sudden power failure can halt an entire production line. Our New Surplus stock delivers full original service life at a lower cost than legacy factory special orders.
Q: Is this Yaskawa power module guaranteed to be completely new?
A: Yes. This module is 100% Brand New Surplus. It has never been installed in an active control cabinet, never energized in a production environment, and carries zero operational wear. It originates from verified surplus reserves, machine builder system overstocks, and canceled automation projects.
Q: Can I hot-swap the power supply module while the control rack is energized?
A: No. Removing or inserting the while incoming power is active is strictly prohibited. Live insertion can cause high-current arcing across backplane power pins, blowing internal protective fuses and damaging downstream CPU and communication modules connected to the logic bus.
Q: Does replacing the require software programming or parameter transfer?
A: No. The is a hardware power delivery unit. It contains no programmable firmware or parameter memory. Provided the input voltage jumpers and wiring connections are configured correctly, the module operates automatically upon power-up.
Q: What warranty coverage comes with this New Surplus power module?
A: We back this New Surplus with a full 1-Year functional warranty. Every module undergoes comprehensive quality verification—including physical connector pin checks, insulation resistance testing, and static electrical checks—to guarantee drop-in readiness out of the box.

WhatsApp: +86 16626708626
Email:
Phone: +86 16626708626